Leaderboard

Popular Content

Showing content with the highest reputation on 04/29/20 in all areas

  1. Privoxy is starting fine at port 8118. Make sure to expose that port (e.g., -p 8118:8118 if you are using docker CLI) and then configure your end machine to use the host's IP address and port 8118. No need for FoxyProxy, Chrome / OS settings work fine. You can check that it's working on http://config.privoxy.org/
    2 points
  2. ***Update*** : Apologies, it seems like there was an update to the Unraid forums which removed the carriage returns in my code blocks. This was causing people to get errors when typing commands verbatim. I've fixed the code blocks below and all should be Plexing perfectly now Y =========== Granted this has been covered in a few other posts but I just wanted to have it with a little bit of layout and structure. Special thanks to [mention=9167]Hoopster[/mention] whose post(s) I took this from. What is Plex Hardware Acceleration? When streaming media f
    1 point
  3. I'm trying to set up an Ubuntu Desktop 20.04 VM. Eventually, the VM locks up and I notice its assigned CPU in UNRAID is pegged at 100%. I've tried several times and sometimes I can get the OS installed, and sometimes it locks up during installation. Wondering if it's the same issue as this? I've attached my XML and diagnostic info. Any ideas? Quite a lot of information for Windows guests here, but I'm having trouble finding equivalent information for Ubuntu guests. I have 3 Windows VM's running perfectly. BTW, I saw @jonp's advice to set UEFI boot mode, i440fx, an
    1 point
  4. Hi guys, I've been running two shucked 8TB WD drives fine for a little while and I added two 4TB Lenovo (relabeled Seagates) SAS drives and they both fail either sort of SMART test immediately with the message "Errors occurred - Check SMART report" No idea why this is happening, I've attached one of the reports but I can't see anything wrong with it? Both drives passed a full preclear but I am wary of using them in the array now. Any ideas? ST4000NM0034_X_Z4F0CYYJ0000R604R0FD_35000c5008463026b-20190510-1636.txt
    1 point
  5. I think it is working now. The machine has been stable for a few hours. I went through the BIOS settings one more time and deeep in there I think I found the correct c-state settings.
    1 point
  6. Yup audio worked for me. Only thing I can think of is, to double check your audio capture settings, which I'm sure you have done.
    1 point
  7. If the filesystem is mounted just do a regular copy with your favorite tool.
    1 point
  8. Thank you for your reply. Great to hear from a fellow home user like myself. Thank you for giving your view on dockers and giving an alternative to TeamViewer. I will watch the videos this evening and educate myself what to do. As you said it is not a technical response but the words “it just works” made me smile.
    1 point
  9. Can you? Yes. Should you? No. The (multi-drive) cache pool is RAID-based (BTRFS RAID). So either you will have 250GB available space (RAID-1) or 500GB available space (RAID-0). I.e. no improvement. A better option is to mount the 250GB as unassigned and use it for write-heavy activities (e.g. temp download files). That will enhance the life span of both drives and still give you more storage space.
    1 point
  10. I've reached out to shoginn on discord but have not gotten a response. He has archived most of his repos on github When I have some time I will see about forking them and re-publishing on dockerhub under my own account.
    1 point
  11. A disk gets disabled when a write to it fails. You have to take manual corrective action to remove the disabled state which is normally to rebuild the disk either to another drive or back to itself (if you think the drive is OK). The process is documented here in the online documentation.
    1 point
  12. Hi Phillips2010 First up I'm no expert. Just a regular home based nerd type So I read your whole post and thought there is a simple answer - Basically Unraid just works ! I was a long time freenas user, it also works as a NAS storage solution but you can't just add more random drives into a freenas pool. Once I filled up my drives I started looking at options and I stumbled upon Unraid. Unraid really has been the best decision I made, a re-purposed dual E5-2690 dell server, running 32GB ram and a 1TB ssd for a cache barely gets
    1 point
  13. It works for any profile, as long as the old device remains connected during the replacement.
    1 point
  14. Only the first one will be accessible when using the user share, both can be accessed when using the disk share.
    1 point
  15. Correct to both No need to resize, Unraid will do it on next array start.
    1 point
  16. Nice to see you solved the issue. A thank you is enough and so you did Now that the vm is working again you should check if the bootloader is logging to file (otherwise files will be written in the efi folder at every boot): If you are using clover: Download clover configurator, menu bar --> tools --> mount efi Mount the clover EFI (name should be "EFI") Open the mounted EFI: Inside there's a folder "EFI" --> "BOOT" and "CLOVER" Enter EFI/CLOVER/ folder and open config.plist with text edit Inside the "Boot" section, search for "Debug" and change it to fa
    1 point
  17. hahahah I tried to explain it much simpler so others reading this could understand as well, that is exactly the same thing was talking about. I did not know about this thread though. I'm still working out some other kinks from my side with some other features I'm working on and will try to test the Sparsness if i understand it correctly when I get some more time.
    1 point
  18. Hi, while i was trying to test the new WSL2 feature it seems nester VM feature is not working anymore. Unraid 6 8 3 VM Windows 10 pro what have i done disabled all VMs, disabled VM Manager, unraid shell modprobe -r kvm_intel modprobe kvm_intel nested=1 edited VM xml template with the following entry under <cpu> section <feature policy='require' name='vmx'/> tried starting VM Manager, no way, always ended in <LIBVrt service failed to start> after some digging and results only showed check pathes
    1 point
  19. I have a GeForce GTX 1050 Ti in an ASRock x370 Taichi motherboard. Unraid seems to find the GPU when I check PCI Devices and IOMMU Groups resulting in these two lines. IOMMU group 16:[10de:1c82] 0c:00.0 VGA compatible controller: NVIDIA Corporation GP107 [GeForce GTX 1050 Ti] (rev a1) [10de:0fb9] 0c:00.1 Audio device: NVIDIA Corporation GP107GL High Definition Audio Controller (rev a1) However, when I make VMs no GPU is available. The same issue happens with the Nvidia Unraid plugin and the GPU Stats Plugin, nothing is ever detected. I'm fairly new to Unraid and c
    1 point
  20. @Mattyfaz i read the issue. I Wil add that path when I am at a computer, or you can create a pull request adding it Doing it now
    1 point
  21. https://wiki.unraid.net/Troubleshooting#Re-enable_the_drive Recommend connecting it to one of the onboard SATA ports first to see if it doesn't happen again.
    1 point
  22. Can you try to switch to opencore to see if the issue is with the bootloader? Simply download the attached file, decompress and overwrite Clover.qcow2 (first make a backup). The file name is Clover, but it's opencore (so you don't have to change xml, but simply replacing the qcow2). I changed smbios data too (still iMac14,1). Clover.qcow2.zip
    1 point
  23. ok lets have a look at a full log, can you do the following procedure:- https://github.com/binhex/documentation/blob/master/docker/faq/help.md
    1 point
  24. That's strange..can you post your vm xml? Please when you post it delete the osk. And also please confirm the following: 1- Catalina 10.15.1 and unraid 6.8.2 works well 2- Catalina 10.15.4 and unraid 6.8.2 has issues 3- Catalina 10.15.1 and unraid 6.8.3 has issues
    1 point
  25. I would love to hear an update on this. Mine is horrifically slow also.
    1 point
  26. Try the attached clover qcow2, backup yours first if this doesn't work. I modified the original Clover.qcow2 from the macinabox github repository, so if you changed SMBIOS data you need to change them again. Config.plist is also the same as the original macinabox, sligtly modified, it should be compatible with the latest revision. It's the latest release, revision 5114 but I cannot test, so not sure if it will boot or not. Just try.. Clover.qcow2.zip
    1 point
  27. I'm not sure but I don't think that he explains how to update the bootloader, there's a pre-made qcow2 clover image, the one you have (r5097), that during the setup the macinabox downloads.
    1 point
  28. I would update clover first (latest release now is v5 r5114) and check if there is any difference (from r5098 there are improvements in Catalina compatibility). Mount your efi, download from github the iso image, mount the iso, overwrite files from iso to EFI, check config.plist and eventually adpt to the new clover revision (compare config.plist files to see if there are new options added/removed). Try to inject also lilu+whatevergreen kexts.
    1 point
  29. I can't install plugins -- I searched for an answer but have not found one. When I try to select the egg file I get [Object FileList] When I try to install the plugin by just copying the egg file to the plugin directory that also doesn't install it In NerdPack I've turned on all the Python options The plugin I am trying to install is AutoRemovePlus which is 2.0 compatiable. Any idea what the issue is?
    1 point
  30. A few posts back discuss the decision to remove it. Any python package that doesn't need compiling can be installed with pip and setuptools. https://forums.unraid.net/index.php?/topic/35866-unRAID-6-NerdPack---CLI-tools-(iftop,-iotop,-screen,-kbd,-etc.)#entry838361
    1 point
  31. Thanks for this tool. I can't find docker-compose on my nerd tools. Am I crazy? What am I missing? https://imgur.com/a/I2o8T4N Thanks EDIT : It looks like maybe it was removed? Tracing back this thread, I installed python3, python-pip, python-setuptools and libffi and then went to console and pip3 install docker-compose and that seems to have installed it? Does this sound accurate?
    1 point
  32. I like having my linux terminal sessions customized with the ZSH shell and oh-my-zsh with git and other plugins. I can set this stuff up on unRAID, but lose all terminal customizations on system reboots. ZSH can stay installed with the Nerd Pack plugin, but I have to reinstall oh-my-zsh via curl/wget and copy my backed up .zshrc back and change my default shell again. I can probably setup a script to do all that via the go file, but is there a better way to just maintain terminal customizations and configs across system restarts? It seems pretty inefficient, especially if I
    1 point
  33. 1 point
  34. I figured out a simpler way, just define $HOME for scripts: HOME="/root" sh -c "$(wget https://raw.githubusercontent.com/robbyrussell/oh-my-zsh/master/tools/install.sh -O -)"
    1 point
  35. For anyone else chasing this broken-Ethernet-at-boot issue, I seem to have fixed it on my system by changing the bridge PCI bus to '0x00' and slot to '0x05' thusly: ... <interface type='bridge'> ... <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> ... Since making the change, over a couple dozen boots, I haven't again seen macOS report the (virtual) Ethernet cable as being unplugged.
    1 point
  36. In this 2017 post: @llonca13 says: That sounds promising! Though I haven't been able to find the original @SpaceInvaderOne (formerly @gridrunner) post referenced, I have attempted to change the slot number in the XML as follows: ... <address type='pci' domain='0x0000' bus='0x01' slot='0x05' function='0x0'/> ... However, when I make just the single-digit change and then click Update in the XML View, I immediately get this error pop-up from Unraid: VM creation error XML error: Invalid PCI address 0000:01:05.0. slot must be <= 0 Any th
    1 point
  37. You don't need to do anything. Docker compose isn't some complicated program it's a single binary file that you add somewhere in your $PATH and you're good to go. The whole install is below. sudo curl -L https://github.com/docker/compose/releases/download/1.18.0/docker-compose-`uname -s`-`uname -m` -o /usr/local/bin/docker-compose sudo chmod +x /usr/local/bin/docker-compose
    1 point
  38. Thank you very much for this guide the performance of this "VM" is amazing (and with 0 aditional kexts WTF ). I know how much time it took and how much time you saved for alot of people.Thank you for that. I have one question..did anyone passthrough entire integrated usb pci controller with success? ..whatever i try it doesnt work..integrated motherboard sound passthrough works great (alc662,with patched applehda) And why is my About this mac showing core2duo(i have sandy bridge i5 2400)? I dont have anything extra in my xml that define cpu(only at the end,qemu: penryn
    1 point
  39. Figured I would post the solution back here.. https://lime-technology.com/forum/index.php?topic=51498.msg533288#msg533288
    1 point
  40. Have you tried nuking your docker image? Turn off docker in settings and go to your appdata folder and delete the docker image? That's about all the help I can think to offer at this point. Well I'm getting closer. Issue was the .conf file location. The required location was noted as /mnt/user/appdata/telegraf/telegraf.conf. It was creating this path automatically, but telegraf.conf was an actual directory. So I removed the directory and placed the file at /mnt/user/appdata/telegraf/. Hope this makes sense, but that is at least got things moving. The issue I have now is the dock
    1 point