Nnyan

I noticed this first b/c the CA plugin gave an error but then i noticed the plugins would not update, upgrade to 7.3.1 failed (tested to see if it can reach the internet). I can obviously reach the server locally. I have rebooted, changes the IP from static to auto (with a DHCP reservation), check/unchecked bridging, tried different NICs (being active), changed DNS, gateways, changed the reserved IP, etc. There is no bonding. Not sure what to do other then try to revert back the 7.3.0 upgrade. tower-diagnostics-20260607-1015.zip

@MiguelBazil I am no expert but I had thought that "Interface Rules" would determine that. Whatever NIC you assign to eth0: would be the default route. But despite putting in my 10Gbe card as eth0 Unraid insists on sending the default route through br1 (bridge interface). >brctl show command tells me that eth1 is attached to br1. I've tried adding routes, messing with the metric to no avail. @rmp5s I don't know if this will be any help but I have noticed that if you have more then one NIC (typically your eth0) with bridging enabled that I would get issues with various things not connecting (Unraid Connect and Community Apps being some of them). Which makes sense since (I THINK) bridging is what allows apps/docker to communicate to that interface so having more than one can be an issue?).

This is annoying, just added a 10Gbe card to one of my unraid servers (the only one that didn't start with a 10g card) and I see all sorts of connection issues. It's like Unraid just WANTS to use the original 1G nic no matter what I do. Server is up but I get things like community apps and Unraid Connect connection errors.

ok , that's a great point. I purchased a Kingston Digital FCR-ML3C MobileLite Duo 3C with a SanDisk MAX Endurance 32GB TF Card (based on some feedback that this would get the GUID from the reader and make it easy to replace the SD card if it goes bad). Based on your post I did find this: So I'm going to go with the fact that this reader just doesn't have an unique GUID (thank you for pointing me in the right direction). The SDCARD did come with a really cheap (EBS) white reader that I didn't want to use b/c it seemed so flimsy. Not sure if installing this the manual way will help with the Kingston reader but I'm willing to give it a go.

Just bought the usb key specifically for this purpose so it’s brand new. I’ll just wait for support.

I have my new unraid server up and running after my other one died and my usb key went missing. Unfortunately when I get to the replace key (where it will blacklist my old usb) I get the following error: Error: {"message":"Request failed with status code 403","data":{"error":"GUID 'XXXXXXXXXX' is already registered to another user"}} I've opened a support ticket but I thought I would post here in case this is something that is known and fixable outside of waiting for support to answer. Thank you

I did contact support several days ago and no reply. I went to do it again and it prompted me to open a new topic in the general support forum for "quicker response" and so here I am.

I need to recover my keys but when I log into my account I do not see anything in there. Unfortunately moving off of gmail I lost all my history prior to 2022 but I did see a few emails to Unraid support about my Pro license back in 2022. Any help will be greatly appreciated, thank you.

Hello all, sorry for the noob question but I have my NAS mapped in Unraid as an SMB share and that works but I just can't figure out how to make this "visible" to the Plex container (installed using defaults). Thank you for your help.

noob to unraid and I wanted to setup OpenVPN so that it could connect to my VPN service (Mullvad) and I can route certain containers traffic to OpenVPN. I'm assuming that I need to install the client and not the server but when I did it asked to to add the Mullvad config file but while I can do the select file drop down it doesn't actually do anything. How do I upload the config file if this doesn't work?

Ok thank you for that information you cleared up a few things for me. Got my setup inline with what you described and I got it working! Thank you SO much for your help.

Hello all, complete UNRAID noob (just purchased license) and even more so with Docker. I am hoping to migrate my current plex server to this container and I've run into a few issues. I'm sure these are just due to a lack of knowledge on my part. container was not reachable to the rest of my home network. Changed network type to custom and assigned an IP. Port forward to this IP and it's now reachable to local servers and outside. Initially I wanted to use an SMB mapping to my current media NAS. After some research I mapped an SMB share (\\10.0.1.53\media) which works fine from my windows boxes in UNRaid. But when in the Plex app it can't find this media folder and I can't seem to manually point to it. I then found a post that I should add this share to the container as a "host path" and this is what I have: Config Type: Path Name: Media Share Container Path: /mnt/user/appdata/binhex-plexpass Host Path: //10.0.1.52/Media Access Mode: Read/Write But I still can't seem to be able to get this "visible" onto my plex container. Thank you for your time and assistance!

Just as an FYI my PSU died (no warnings) and I found an inexpensive version that works (installs just fine needed two molex splitters). If you ask me it seems a touch louder than the stock but not a big deal. http://www.atxpowersupplies.com/250-watt-flex-atx-power-supply-FLEX-200W.php

Thank you! I figured out it's just a version. OK not sure how to use the P19 version vs the P11 version posted here. It seems like the firmware is the same (at least the file name is the same) 2118it.bin. OK just replaced the files in the firmware to the newer version but alas I get the "Failed to initialize PAL" message. I found one other person that had success downloading the SAS2FLASH.EFI file from LSI and I gave that a try but I just keep getting wrong file name. I'll try another system next.

I'm sorry if I missed this but I just want to be clear, I have a RS2WC080 that I want to flash into IT mode, I'm not sure what the differences are between the P10 and P11 files. Thank you in advanced for your help.