LoyalScotsman

sorry i missed this been very busy at my work so not been able to check good you got it running in the end

old version 6.8.3 upgrading to 6.9.2 I made a backup of the flash before I pushed the upgrade so downloaded the upgrade from within the web GUI and started the install, then i stopped my array and rebooted unraid since doing this I can no longer ping the server. I connected a monitor to the server and i have went into gui mode in the server and it is not able to load the gui via localhost from here I then opened a terminal to look and see if the IP has been lost but when doing ifconfig eth0 it is displaying this error - "error fetching interface information: device not found" i am not 100% clued up in linux hence why i have got logs and reaching out here for assistance before i try anything else thanks in advance for your assistance if you need anything else please just ask, hopefully this is a easy fast fix. edit: also tried to ping the gateway from within the server terminal and it failed tower-diagnostics-20210413-1051.zip

Hello Thanks for your help diagnosing the suspected drive I decided to rip all data off it and it finished around an hour ago thankfully cause I just got an email from unraid saying the disk is not OK and after a further investigation in archived notifications it turns out the disk is now flagging 147 errors So i have pudged the drive off my unraid and shunk the array for now, but 2 new 4tb wd red disks have been ordered Also an FYI the smart check still ain't completed and been stuck at 90% for a good few hours. Image below Sent from my SM-G973F using Tapatalk

so a small update i ran the extended disk scan it failed at 90% saying the disk need spin up even though it was, so i decided to run a disk diags test on the drive and got the following results on disk 5 not looking good going by the stats, a huge drop then raise then drop again which is very worrying so i have started pulling everything of that drive. i have reran the extended test but tbh it is not looking good

ahh ok so the seagate disk is ok for now EDIT i missed your hyperlink its ok the Seagate disk has no errors i will start it now and advice back results

not fully sure how the quoting works so i will just type it as comment so i can advice after stopping all dockers the parity check has completed also mover is nearly done as well since the parity check is completed good to know it kicks in during the parity check so the receilt changes i did to unraid was setup grafana so i am not sure if this is what has causeed the read/write delays. it had no issues before this. so i looked for the errors you mentioned and i will monitor them for the next few days then up it to a week check and so on. But i checked the other drives for the same sections you listed above and found the following so for following disks ST4000DM004-2CV104_ZFN2TLLK - 4 TB - which is not a very old disk has the following and is a disk my friend provided me due to low space on the array ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 083 064 006 - 214020306 7 Seek_Error_Rate POSR-- 077 060 045 - 49259391 9 Power_On_Hours -O--CK 098 098 000 - 1982 (165 171 0) there is no multi zone error rates on this disk WDC_WD10JPVX-22JC3T0_WD-WX31E73AWSD2 - 1 TB ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 198 198 051 - 33639 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 30 so i was planning on picking up 3x WD red disks in march but going by the above errors on those disks should i just get them replaced sooner ? oh that makes sense why it had passed the 1TB disk

you also mentioned disk 5 has passed it, are you able to work out disk the parity check was on ?

thank you for reviewing issues on parity like what ? i am aware the parity disk has 1 "UDMA CRC error count" error but this has been there for a while now, also this disk is an older disk. So i have just stopped all dockers, is there anything you want me to do or just wait and see if there is any change ? I am aware that my auto downloader has picked up something but this will be in my cache and not been moved into the array as of yet I can also see that it says mover is running, which if i am write to believe mover shouldn't kick in during a parity check ?

sorry full logs uploaded now i also uploaded a grafana chart to give an idea when it slowed down server-diagnostics-20210115-1040.zip

Hello i hope someone can assist and point me in the correct direction. So i would like to start with the following mover took 24 hours to move 50GB normally this is done within an hour. parity check start the other day so far it has took 1 day to get to 98.4% and it says it will take longer to complete a parity check normally only takes 10/12 hours. i noticed the estimated speed is drop down into the KB for a long period of time normally it is steady in the mbs i also noticed it has over 600 sync errors corrected screenshot below I have scanned the logs and found the following i noticed this in the logs - Jan 14 16:36:25 Server kernel: md: disk5 read error, sector=1729901760 it is only with disk 5, is this disk failure or maybe a cable issue ? can someone please review logs and voice there thoughts logs attached server-syslog-20210115-1023.zip Just checked Grafana and it reports the following so this slow down started around 1am GMT image below

Hello just an FYI I got it working I will put it down below so I am running deluge version 2.0 so the older AutoRemovePlus-0.6.1-py2.7 plugin doesn't work so after some searching I found a newer version which is built for deluge 2.0 link below https://forum.deluge-torrent.org/viewtopic.php?t=55733 the actual upload via the webui still doesn't work but see if you download the plugin and then navigate to the "/mnt/user/appdata/binhex-delugevpn/plugins" your path might be different, but once in the plugin folder just drop the "AutoRemovePlus-2.0.0-py3.8.egg" into the folder, then restart deluge and you are sorted it will then show up in deluge oh just incase hers a guide to setup the AutoRemovePlus-2.0.0-py3.8.egg - https://docs.usbx.me/books/deluge/page/automatically-remove-torrents-using-autoremoveplus

Hello sorry to revive an older post but did you get a solution for this cause i was just trying to do the same but having the same issue ?

thanks I got the Plex Library Growth working. but not full sure on the unassigned disks I have attached a screen shot on the right is that what you are referring to ? This is the first time I have set this up so not fully clued up

So i got UUD version 1.5 installed and all appears to be working but a few items so I have a few questions see below first question my Plex Library Growth is not working any advice see image below Second question what is the "unassigned i/o (read & write)" pulling its data from cause the writing on it is very high even though I only have 1 unassigned device and its a 16GB USB "only using 534mb out of the full 16GB" so I'm a wee bit confused since the write is shown as high as 500GB any help would be appreciated I have not removed the unassigned USB disk because it is setup for backup purposes but only gets writing to once a week. ask me any question if you require more info