socalunraid

when i rebuild: reiserfsck --rebuild-sb /dev/sdb or reiserfsck --rebuild-sb /dev/sdb1? thanks.

thanks.

thank you. Currently copying disk 10 using : dd conv=noerror if=/dev/sdl of=/dev/sdx using sdl since md10 isn't recognized sdx is my extra hdd after i punched that in telenet, i just have a green cursor? is that is to be expected or is the process frozen? any signs of progress? % thanks.

I'm finally getting around to doing the reiserfsck --rebuild-sb There are many questions asked? Enter block size [4096]: No journal device was specified. Is journal default? y/n: I've searched and could not fine any posts with instructions. Thanks.

ran reiserfsck on disk 9 which state no corruptions. I rebooted array, disk 9 showed up again, no longer unformatted? strange. I'm elated. But what's going on? Thanks. Now gonna duplicate disk10 and try reiserfsck rebuild sb

any advice?

syslog.2 any other logs I should pull? syslog.2_4.11.13.zip

syslog.1 syslog.1_4.11.13.zip

syslog

before doing anything, my disk 9 just became unformatted.?? I have attached short smart report of disk 9. what is happening? thanks.

I ran the check on disk 9, a good disk. Everything was okay. I ran on disk 10. It suggested rebuild sb. I included screen capture. How do I duplicate disk 10 before trying to rebuild per your instructions. I'm new to Linux. Thanks.

Thanks for the reply. How do I make a duplicate of the disk?

Any ideas? thanks.

I tested the original redballed disk 1 with disk internal linux reader, and it was able to read it and there was data. It noted ReiserFS file system. I shut down the array, and pulled out the hard drive cage which included disk 8, 9, 10 (disk 8, and 9 are fine. disk 10 is "unformatted" and never redballed as I can tell, with good smart report). Disk internal linux reader notes noted these disks as linux system and could not read them? Not as ReiserFS file system? Not sure what that means? Thanks.

Any ideas? thanks.

sorry, after I thought I copied the logs, I powered down to recheck the connections. I've attached a new log. Other logs are gone. syslog_4.5.13.zip

another log log_4.zip

another log log_3.zip

thanks. goes only back to 3/31 here they are. log_2.zip

thanks for the reply. attached screen shot.

did a screen capture. only 4/2 to 4/3 thanks.

in telenet cd /var/logs is says No such file or directory. Thanks.

disk8 is fine. disk10 was always green but somehow became unformatted. How do I recover data from disk10?

Hi, I've been running my array since 2010 24/7 without any problems which includes: Unraid 4.7 with unMenu Sempron 140 MSI 785GTM E45 2gb DDR2 Corsair TX650 V2 2 x Promise SATA300 TX4 controllers 11 x 2tb hdd Last Tuesday 3/26, I added some files to disk8 and ran a parity check. There were errors and disk1, and disk 1 was red balled. Instead of trouble shooting, I thought it would be easier just to power down and replace with a spare new 2tb drive I had. I proceded to rebuild. During the rebuild process I noticed that my disk 10 drive somehow became unformatted and was still green. I didn't cancel the rebuild to see the results when finished. The results were disk 1 was not rebuilt and still unformatted. Disk 10 is unformatted. I still have the Original disk 1 untouched, out of the array. I pulled the syslog file from the flash folder on the network and put it in text (just now, so not sure if it will help). I didn't know every time the array powers down, the syslog resets? I included a short smart report of disk 10. Is there any way I can recover data from disk 10? Has any ever have this happen? red ball one disk then for some reason another is green but unformatted? So, I have haven't done anything else to the array: Just replaced disk 1 and tried to rebuild which failed. I have added, deleted, or modified any files on the server since the parity check failed. Since the array has been "no maintainence" I totally forgot the correct steps to troubleshoot. I should have pulled syslog, smart tested, and come to the forum for help. AND NEVER rebooted or powered off. Pleeeeeeeeeeeease HELP. syslog_text.zip smart_test_report_for_disk_10.zip

Thanks for all your help. Not sure what happened? Maybe the controller card was not seated well in it's slot? Everything works fine now. No errors. SMART works on all ports. Going through this, I now know how to trouble shoot and rebuild. THANKS AGAIN.