[Reduce power consumption with powertop]

[Reduce power consumption with powertop]

1 hour ago, FlowDE said:

 

Try to Update your Unraid to 6.12.8

"Problems due to Realtek network cards

Upgraded kernel fixes the deadlock issue with jumbo frames and the in-tree Realtek 8125 driver. However, we still recommend following the advice above regarding jumbo frames.

If you continue to have network stability issues and Tools > System Devices shows that you have a Realtek ethernet controller, grab the part number shown and search Community Apps to see if there is a Realtek vendor-supplied driver plugin for that device. For more information"

And if i am not wrong in the "Appstore" there are some Realtek-Drivers

 

  

You don't need to you can check if the CPU enters higher C-States with Powertop after unplugging those cards (care about your Data bevor doing that) 

Thanks, but after the update in 6.12.8, i'm still stuck in c3

[Reduce power consumption with powertop]

Hi,

 

i follow the tuto and my server his stuck in C3 with this :

 

- Asus TUF GAMING B560M-PLUS

- i5-10400

 

Any ideas ?

[NO GUI and network disconnected]

24 minutes ago, JorgeB said:

Nov 10 01:04:22 JamesServer kernel: macvlan_broadcast+0x10a/0x150 [macvlan]
Nov 10 01:04:22 JamesServer kernel: ? _raw_spin_unlock+0x14/0x29
Nov 10 01:04:22 JamesServer kernel: macvlan_process_broadcast+0xbc/0x12f [macvlan]

Macvlan call traces will usually end up crashing the server, switching to ipvlan should fix it (Settings -> Docker Settings -> Docker custom network type -> ipvlan (advanced view must be enabled, top right)).

ok, thanks i'm going to test that

[NO GUI and network disconnected]

On 10/31/2023 at 8:16 PM, JorgeB said:

Enable the syslog server and post that after the problem.

My server have bug again, this is my syslog :syslog-192.168.1.100.log

[NO GUI and network disconnected]

ok, i change for this and it's work

[NO GUI and network disconnected]

On 10/31/2023 at 8:16 PM, JorgeB said:

Enable the syslog server and post that after the problem.

Were is save the log file ?

 

i check in my cacheDevices and i see nothing

[NO GUI and network disconnected]

1 minute ago, JorgeB said:

Enable the syslog server and post that after the problem.

ok, thanks

[NO GUI and network disconnected]

Hi,

 

Sometimes my unraid server bug and i don't have gui, the server is disconnected to my router i don't know why, if someone have am idea please.

 

 

Log in my router : 

 

thanks

 

jamesserver-diagnostics-20231031-2003.zip

[[Plugin] Docker Folder]

That would be very nice to add a status button for the users like me how which disable container name and button

Example :

[[Plugin] Docker Folder]

3 hours ago, shpitz461 said:

Just click the toolbar lock and turn it red (unlocked), then use arrows to the left of each folder and drag to change order.

Thanks !

[[Plugin] Docker Folder]

Hi, 

 

how can i change the folder order please ?

 

 

Thanks.

[Reduce power consumption with powertop]

On 10/15/2023 at 2:45 PM, Lolight said:

Apparently there isn't one.

But there are reports of at least some SATA expansion cards playing nice with C-states.

To bad  i can't use sata my case have hot swap disque with direct sff port...

I will follow this thread in hoping someone will come up with a solution 

[Reduce power consumption with powertop]

You know if there are LSI card compatible with c-states ?

[Reduce power consumption with powertop]

Stuck in c3 cause of sas 9211-8i 😢

[Impossible to start vm from GUI]

The problem come from old plugin i uninstall few plugins and it’s work

[Impossible to start vm from GUI]

but i still have a problem with the button for start the vm his doesn’t work and i have the same problem for the docker container

[Impossible to start vm from GUI]

46 minutes ago, itimpi said:

Once a new image is created then you can tick them off under Apps->Previous Apps to get all the ones earlier installed via the Apps tab automatically reinstalled with the previously used settings. 

Ok thanks it’s work

[Impossible to start vm from GUI]

I need re re-create the docker vdisk ? If a do that i have to recreate all my containers? (I have more than 50...)

[Impossible to start vm from GUI]

jamesserver-diagnostics-20231003-1530.zip

[Impossible to start vm from GUI]

I try to stop the array and his stuck like this 

[Impossible to start vm from GUI]

And now the docker service doesn’t start wtf happen with unraid

[Impossible to start vm from GUI]

27 minutes ago, Mainfrezzer said:

Mhmm, that does seem odd and i couldnt find anything to indicate that something is "wrong". The only reason i could find is that it tried to attach to a network that didnt exist, still weird it started over cli

But another question: Thats your only issue?

Im surprised your server hasnt crashed yet since youre running a bridge with macvlan and have call traces.

https://docs.unraid.net/unraid-os/release-notes/6.12.4/#fix-for-macvlan-call-traces

The vm,start with consol vnc wotk but the stop button doesn’t work

[Impossible to start vm from GUI]

12 minutes ago, Mainfrezzer said:

Mhmm, that does seem odd and i couldnt find anything to indicate that something is "wrong". The only reason i could find is that it tried to attach to a network that didnt exist, still weird it started over cli

But another question: Thats your only issue?

Im surprised your server hasnt crashed yet since youre running a bridge with macvlan and have call traces.

https://docs.unraid.net/unraid-os/release-notes/6.12.4/#fix-for-macvlan-call-traces

No after reinstalle unraid my windows cm lag in game i dont’t know why

[Impossible to start vm from GUI]

Hi,

 

i reinstalle my unraid (usb key error)

And now impossible to start the vm from the gui (it's work with cli)

 

my diag : 

jamesserver-diagnostics-20231002-2236.zip