ozma64

I am getting this same error with the same line number... I cant see that anyone had actually responded to this... could someone advise?

I can but i need to find a part for me system Fan. For some reason whenever i have the WebGUI for Unraid up, it periodically maxes out my fan speed intermittently. However, then i upgrade to 6.10 it does it intermittently at all times, not just when i have the WebGUI up.. im not sure what is causing it but i ordered a part due to this to take my fan's PWM off the motherboard and move it to an adjustable turn knob on the back of the server.. I just havent had the chance to install it yet, so i was when i start digging into m HDD upgrades that im doing. So ill have it upgraded eventually.

additional note, when i reinstalled the UD plugin, the Dev4 device remained gone. I'll monitor to see if it or more comes back

Yes, it is only showing the Dev4 device on the dashboard and INI file. Everywhere else it is not showing up. When refreshing the UD page listing, it remained the same, Dev4 did not show up on it but remained on dash board and INI file. However, when i uninstalled UD from the server, the Dev4 drive disappeared from the Dashboard and INI file. So if that is the case, im imagining this isnt an issue with Unraid but UD instead. Do you concur?

Is this the page you are talking about?

Could you clarify where that page is? The only pages that hold UD information that i know of are on the Dashboard, Main tab, and the Unassigned Devices Settings page (which doesn't show the individual devices. I have already posted photos of what i see in the Dashboard and Main Tab for UD. I cant seem to find any other location that holds Unassigned Device information.

The 3 drives show up and also this: ["dev4"] name="dev4" id="ST1000NM0023_35000c50058d735ff" device="sdj" sectors="1953525168" sector_size="512" rotational="1" spundown="1" temp="*" numReads="2688949" numWrites="5236" Which is odd because the identifier sdj is another drive my array is using... ST1000NM0023_Z1W2B5WF00009442RURN - 1 TB (sdj) Could i have a corrupted Unraid install?

Greetings, I have been having an issue recently where additional unassigned drives have been populating on my dashboard under the Unassigned category. Currently I only have 2 mounted drives for Plex usage and 1 Precleared drive pending being added to my array at a later date. However, I occasionally get a 4th Dev device (and on occasion even a 5th, 6th, and even 7th) listed on the dash board even if the Main Array panel shows only the 3 drives.. Does anyone have any idea what may be causing this? I have included my diagnostic files as well. Typically the extra Dev device(s) disappear after a reboot of the server. I'm kinda at a loss on this... multimediaserv-diagnostics-20220724-0850.zip

Alright ill set it up and see what happened before the reboot if it happens again

I have another question on this.. Could this issue cause Unraid to become unresponsive to Array Shutdown commands? a couple of the attempts i had made to put the 6TB drive into the array caused Unraid to lock the array up where it would not stop the array when i clicked on it to do so rebooting Unraid from the GUI wouldnt work either and i had to hard power cycle the server... Could this issue cause something like that to happen?

The backplane is most likely the issue then, the HBA and breakout cables are basically new.. but the backplane is rather old and shabby as it came with the old chassis i have everything in. I bought it used from my work. I also think a capacitor is getting loose on it so that's the most likely suspect... i got a new one on the way to replace it. Cross my fingers on it. Appreciate the second opinion

Alright, thank you for clarifying for me.. as for that block of logs there... if im reading it right, the drive is losing power repeatingly? Am I correct? if it is a device reset, what could cause it besides a cabling issue?

Hello, I have been attempting to upgrade my Unraid server from 1TB drives to 6TB drives. I have been trying to get the Parity drives upgraded however every time i try, the parity sync runs very slow (5mb a sec) for about an hour and then it fails. Fix Common problems states that they are Read Errors, however my syslog shows a wall of the following write errors before the drive is disabled: kernel: md: disk29 write error, sector=XXXXXXX I have ran multiple SMART tests on the drive with the tests completing without errors, and the drive has passed multiple preclear runs with full pre reads and post reads with no errors being detected. I'm thinking this is a cabling issue or a problem with my HBA/Backplane, however I would like a second opinion to ensure that I dont go on wild goose chases with this. The drive that is failing is WDC_WD60EZAZ-00SF3B0_WD-WX42DA1L45HN (sdi) It fails weather i try it in Parity or Parity2 position. Whenever i fail back over to my 1TB parity drive, Parity sync completes without issue (Please note that no drives were removed during testing so both drives are installed at the same time for easy swapping within the configuration) My 1TB parity drive is: WDC_WD10EZEX-00WN4A0_WD-WCC6Y3EATE71 (sdd) I uploaded a copy of my diagnostic reports. Please provide any advisement you may have that might direct me in the correct direction. Thank you (photo of my "Fix Common Problems" report:) multimediaserv-diagnostics-20220718-1236.zip

That did it, much appreciated!

@ich777 Well i managed to repair my MineOS Container... looks like the Java got corrupted somehow so im going to move back to that. However I'm trying to remove the Minecraft fold from my Appdata share and it refuses to delete the Runtime folder and all the java contents in it. I went into terminal and ran chmod to set it to full perms but the folder still remains... Has this happened for others? and how do I delete it?

Thats no problem, I will appreciate it if you do when you can. Well the thingis that Forge isnt started via Jars like vanilla... it runs a set of commands within the Library to start. I did just as you said and it didnt work

Well i am looking at Binhex's Minecraft Container configuration and it is rather... unintuitive or at least not very straight forward... there isn't any real explanation on what each setting is and when I loaded my server into it and set the configuration the best I could, it failed to load.. I liked your App because it it is rather straight forward..

Thank you for this information.. I have read the entire issue there and Im having a hard time following unfortunately. Do i need to make a new Variable on the Container setup? If so, how should I set it up.... of if not, what settings should I add and where?

The masterlog.0 file shows this: Ill check the binhex Docker as well.. If anyone else has any advisement, i would appreciate it

I tried Java11 and that had no change... I then tried Java 16 and i had a change in the log reports: And here is what my Server Logs say now: That seemed to show even less when i did it:

I do not have any mods server or client side installed yet. I was just trying to get the server to actually run first so i pulled out all of my mods for a fresh install. I will attempt to try other Java Versions

I have Java 17 installed on my computer and this same server will start and run on it.. I dont think it is a Java Incompatibility . It looks like the error from the Container logs are truncated... i have added another snapshot of my actual Server Logs to my previous post if you would like to review it

ich777, I am trying to install Forge using your MinecraftBasicServer Docker App. I used to use MineOS, however, the MineOS docker is no longer starting any Servers i have so i have abandoned it to use your App. I can get the server to run with vanilla Minecraft however it will not run using Forge. I have been able to get Forge to work on MineOS Docker by moving the Forge Universal file from the library directory to the Main directory for the server and passing the following Java arguments: @user_jvm_args.txt @libraries/net/minecraftforge/forge/1.18.1-39.0.66/unix_args.txt When do this it on MinecraftBasicServer, it tried to run but then keeps failing.. I have seen other people in this thread have similar issues but no real answers are being provided as it seems the requests are getting lost in other unrelated posts. Could you please provide some advisement. Below is my Logs showing the failure loop and argument settings: EDIT: Here is the full Error from the server's log files.. the Container Log files doesnt seem to show it all:

Thank you, Terraria is now working. I appreciate the update!

Thank you ich777. I will await your advisement. Just glad to hear I didnt botch something here lol.