shpitz461

Hi, I've installed the plugin via ssh, and when I call 'status' I get the following: When I run one of the parity status scripts available in this post: I get the correct status: And here are the stats from var.ini: Any idea why the plugin shows the 0.1%? It's stuck at 0.1% for hours. Thanks

Another option would be to get a DAS, aka disk shelf, suck as the NetApp DS4243/6 or DS4486, Dell MD12xx or MD14xx, etc... There's also a 60-drive shelf available (DE6060) but it is way too expensive, and very loud. Note that some units accept SATA in the SAS enclosures and some don't.

Is there a way to pause parity check from commandline? My GUI is unreponsive, but I was able to get a command window to open. I can't access any GUI pages, so I cannot install the parity tuning plugin. I've ran the script @blender50 posted, so I know parity is running:

Hi, any idea if I can use Traefik's letsencrypt process to generate certs for mailserver? Right now I have Traefik set to generate wildcard certs, so essentially I only have my main domain cert used for all subdomains. Thanks EDIT: Yep, I just followed their documentation here: https://docker-mailserver.github.io/docker-mailserver/edge/config/security/ssl/#traefik-v2

Haha,nice fix!

Thanks, that seem to do the trick!

So all 4 ports are on the same subnet? I think this is bad practice. Why would you need to directly connect the two on top of connection to the switch? This is what my ifconfig shows: I noticed that your eth0 doesn't state RUNNING, mine does. Is eth0 the port for direct connection between servers? What happens if you remove the direct cable between servers and just have each one connect via the switch?

Is there a way to share /mnt/user via NFS similar to the trick done via SMB? I'd like to access all shares with a single drive letter.

Or maybe bad/loose data cable connection? Maybe there's a firmware update? It's also weird how unbalanced the writes are to the 2nd parity, 7M vs 675K writes. I would expect they should always match exactly. Here's what mine looks like: Also, some of your drives appear to be running hot, heat is the no.1 HDD killer. See if you can get some more fans blowing on them. Did you try to change their physical location in your case? Recheck cables (data and cable) are fully seated.

Did you try resetting network.cfg on the Unraid USB stick? /config/network.cfg You can install unraid to another stick and then copy the network.cfg to your existing install and try setting up the network again? Here's what mine looks like: I have two cards, dual-port each. My eth0 port is the 'main' one, eth1 is not connected, and eth2 and eth3 are passed-through to VM's. Now, you said they are directly connected, so none are connected to a switch so they are available to other devices in your network? Or you have dual ports and one port is connected to a switch and the other directly to the other NAS?

Run the commands so we can see the exact models you have. Here's a good thread for flashing hdd firmwares: https://forums.servethehome.com/index.php?threads/updating-the-hgst-hdd-ssd-firmware.22381/page-9 Here's a link to Hitachi firmwares: https://files.hddguru.com/download/Software/

Run this command: Then run this command on your specific disks to get the full firmware version: I have 4 of the He10, one failed a few months ago after 4 years of usage. Mine are all on firmware 'LHGNT384': Are yours on this firmware also? Also, are there any jumpers on the drive? It's odd the drives downgrade to SATA2 (3gbps) instead of SATA3 (6gbps). What happens when you connect only the He10 on the same controller?

Hi Everyone, I'm seeing this error in syslog: Any idea how to track the root cause of the issue? Is this complaining about PCIe slots? If so, which one? This is what the system device 80:01.x is: The motherboard is an ASRock ROMED8-2T. Thanks!

There's already a docker container for it you can use. It has a full gui: And if you open its console, you can run mkvmerge, mkvinfo, mkvextract to manually process files:

Looks like it. Did you try to reset BIOS to defaults and reboot? Did you check for BIOS updates for the motherboard? You can try removing all cards and see if you can boot a bare system (memory, cpu, gpu if needed). You can try to boot ubuntu or debian live cd and see if you get the same errors? The new flash drive you tried, did you install a fresh unraid on it? or copied files from original flash drive?

Did you zero/pre-clear the drives before adding?

I've also seen this video about the IO Wait issue:

Did you disable the VM and docker processes? or just stopped what they do? I wonder if that makes a difference... After you stop everything, run 'iotop' and see if any processes are using the disks. Run the following command and paste the output: Here's an example with mine:

Do you have any VM's or docker containers running during the scan? If yes, better stop both services, then parity check will speed up.

Is this your Rocket 1508? It shows full Gen4 16x connection: From what I understand, since PEX is used (bifurcation controller), all the drives share 16x, so in theory 4 drives will operate in full x4 speed, but more drives operating simulataneously will share 16x bandwitdth and will slow down, since you can't fit 32x bandwidth in a 16x-wide bus. Did you try to boot your machine with a live ubuntu or debian and see if you get the same performance? Did you try removing all other pcie cards and test with the rocket solo? How many drives have you populated in the controller? If not 8 drives, did you try to move the drives around to see if you get any better performance? i.e. slot 1 and 2, 2 and 3, etc...

Ha, same happened to me, it appeared the firmware was not updates, but after a reboot it is. Updated an 990 Pro from 3xxxx to 4xxxx, thanks OP! After clicking 'Y', it takes a few seconds then a new screen showing to press any key to exit.

Did you try a different browser? Did you try to clear browser data (especially cookies)? http vs https? Is the GUI on default port or did you change it? Another thing you can try is open the browser you use, press F12 if using Chrome to open the dev tools panel. Switch to Console tab, then open MAIN page of unraid. Do you see any errors logged? This is what mine is showing when I open MAIN tab:

You bet, it's probably old remnants from much older versions. I wonder if there's a tool that can scan the USB drive and produce a list of 'suspect' files...

Thanks @JorgeB, I deleted the plugin folder and rebooted, no more errors.

if I don't have any pages open, the error stops. And I tried MAIN and VMs tabs, both produce the nginx errors in the log: