Dark_Surger

Thanks mate, I'll keep this thread open, really appreciate the help!

Ok, so i tested it in a crosshair MB and it worked fine, going back to my B450 Aorus Elite, and doesn't work. I run a 10GBe NIC just fine. So is it an issue with the gigabyte bios?

Didn't work, did i get the wrong pins? No change

Champ, thanks, will post update, thanks SO MUCH!

Hi, I can do this, but what part exactly? Will post pic. Can you circle the pins to cover please.

Hi I picked up a Silverstone 9217-8i SAS card. ( ECS04 SAS Controller) https://www.scorptec.com.au/product/kvm,-hubs-&-controllers/controllers/70368-sst-ecs04?gclid=CjwKCAjwjuqDBhAGEiwAdX2cj6UkZ1tujPaS2v3l_yFyjPp-iKfQHBlg-PB9IgnFtpj1ucFLhhbl6xoCUc8QAvD_BwE Put it in and computer skips bios, and just sits on a black screen with the flashing line on the top left. From every bit of information I could find it needs to be flashed into IT mode, but no further information on this. TROUBLESHOOTING TRIED; Remove card-system works Remove UNRAID flash drive and bios reset Tried multiple PCI-E slots. Any help is appreciated.

So basically my selected NIC does 10GBe ONLY. No in between. No 5GBe, 2.5GBe. Only 1 or 10.

& shouldn't the NAS say 10GBe not 1? Network: eth0: 1000 Mbps, full duplex, mtu 1500 eth1: 1000 Mbps, full duplex, mtu 1500 eth2: 1000 Mbps, full duplex, mtu 1500 Souldn't the host say eg. eth1: 10000 Mbps

I didn't understand that comment. X540-AT2 haven't 5G support, so if connect with a 5G NIC, then negotiate 1G should be normal.

Sorry, newbie haha

tower-diagnostics-20210216-2203.zip

Hi, I am building a NAS box running PAID UNRAID software. Model: Custom M/B: Gigabyte Technology Co., Ltd. B450M AORUS ELITE Version x.x - s/n: Default string BIOS: American Megatrends International, LLC. Version F60h. Dated: 02/04/2021 CPU: AMD Ryzen 5 3400G with Radeon Vega Graphics @ 3700 MHz HVM: Enabled IOMMU: Enabled Cache: 384 KiB, 2048 KiB, 4096 KiB Memory: 64 GiB DDR4 (max. installable capacity 128 GiB) Network: eth0: 1000 Mbps, full duplex, mtu 1500 eth1: 1000 Mbps, full duplex, mtu 1500 eth2: 1000 Mbps, full duplex, mtu 1500 Kernel: Linux 4.19.98-Unraid x86_64 OpenSSL: 1.1.1d Uptime: EDIT: IOMMU is set to auto in BIOS. So basically I am using eth0 for internet, and Enabled bridging on : eth0, eth1, eth2. the 10GBe NIC is: IOMMU group 8:[****:1528] 01:00.0 Ethernet controller: Intel Corporation Ethernet Controller 10-Gigabit X540-AT2 (rev 01) IOMMU group 9:[****:1528] 01:00.1 Ethernet controller: Intel Corporation Ethernet Controller 10-Gigabit X540-AT2 (rev 01). The Issue is this: INTERFACE eth0 eth1 eth2 lo Inbound: 27.5 KbpsOutbound: 9.1 Kbps eth01000 Mbps, full duplex, mtu 1500 eth11000 Mbps, full duplex, mtu 1500 eth21000 Mbps, full duplex, mtu 1500 lo loopback This is the Issue. One is these connections is connected to a 5GBe post on Crosshair Formula MB Ethernet Port. Cables are CAT6a running from 10GBe PORTS.