mmgarci30

Thanks, just found it-

I've just found the solution... https://wiki.unraid.net/UnRAID_6/Storage_Management#Rebuilding_a_drive_onto_itself

Hi team I've the same issue a disk has been marked as failed due to bad conexion on an splitter power cable. The splitter has been replaced, and the smart looks fine. But that disk is still in emulated state. The link provided by @JorgeB to the troubleshotting wiki does not work as the Re-enable_the_drive section does not exists in the page. Where can we find that procedure? Thanks and regards

Thanks mate, got the message. But I'm still having issues with Windows 10 PRO Creators Update 1703 (10.0.15063). I0ve the issues both with 6.3.5 and 6.4.0-RC6 I'm unable to authenticate in the Unraid box via Samba. The option sugested to disable SMB 3.x and SMB 2.x it's not posible to prevent ramsoware atacks that usually spread via SMB 1.0 Thanks

Hi RobJ Since the change of the forums, all the links in old format doesn't work. Would you mind update the links? Thank you.

Hi neilt0, Please would you mind to explain where you have added the seventh drive inside the case? Thank you.

Hi mates, I've just received 2 new WD30EFRX (3Tb RED Edition) one of them I forgot to preclear ir so no data. But This is the results. ================================================================== 1.13 = unRAID server Pre-Clear disk /dev/sdb = cycle 1 of 1, partition start on sector 1 = Disk Pre-Clear-Read completed DONE = Step 1 of 10 - Copying zeros to first 2048k bytes DONE = Step 2 of 10 - Copying zeros to remainder of disk to clear it DONE = Step 3 of 10 - Disk is now cleared from MBR onward. DONE = Step 4 of 10 - Clearing MBR bytes for partition 2,3 & 4 DONE = Step 5 of 10 - Clearing MBR code area DONE = Step 6 of 10 - Setting MBR signature bytes DONE = Step 7 of 10 - Setting partition 1 to precleared state DONE = Step 8 of 10 - Notifying kernel we changed the partitioning DONE = Step 9 of 10 - Creating the /dev/disk/by* entries DONE = Step 10 of 10 - Verifying if the MBR is cleared. DONE = Disk Post-Clear-Read completed DONE Disk Temperature: 31C, Elapsed Time: 35:22:10 ========================================================================1.13 == WDC WD30EFRX-68AX9N0 WD-WMC1T0667118 == Disk /dev/sdb has been successfully precleared == with a starting sector of 1 ============================================================================ ** Changed attributes in files: /tmp/smart_start_sdb /tmp/smart_finish_sdb ATTRIBUTE NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS RAW_VALUE Temperature_Celsius = 119 120 0 ok 31 No SMART attributes are FAILING_NOW 0 sectors were pending re-allocation before the start of the preclear. 0 sectors were pending re-allocation after pre-read in cycle 1 of 1. 0 sectors were pending re-allocation after zero of disk in cycle 1 of 1. 0 sectors are pending re-allocation at the end of the preclear, the number of sectors pending re-allocation did not change. 0 sectors had been re-allocated before the start of the preclear. 0 sectors are re-allocated at the end of the preclear, the number of sectors re-allocated did not change. The box is a HP Microserver NL36, 8GB of ram, the bios is flashed to the last revision that allows a few more options in the shouthbridge. All ports in ACHI mode full speed. The disk I,m preclearing is in one of the disk slots through the minisas cable. UnRaid 5.0-beta14 It looks strange, in the preclear and postclear phases it begans a 145mb/s pretty good speed, but after a few minutes the speeds progresively slow down till 45mb/s where booth read phases are around 60% it speed up again to 120 / 125 mb/s and then progresively slow down again till finish. All the time there is no body accessing de array and the IO wait in a top command grows till 85%. When I've precleared mi WD20EARX 10 months ago I don't think they took so long ... Has somebody reported that slows down? I will update the pendrive, take a look to the bios and make a new test. Thanks.