• Posts

  • Joined

  • Last visited

Everything posted by bpalhares

  1. Hi I'm trying to run the script via CA User Scripts. I have checked and I have Enable IPMI Over Lan activated (DELL R515). I have installed Nerd Tools and IPMI. If I go to the terminal I can execute all the IPMI commands and control the fans speed. If I try to execute the script via CA User Scripts, it doesn't work, returning Error: Unable to establish IPMI v2 / RMCP+ session /tmp/user.scripts/tmpScripts/fan_ipmi_control/script: line 26: [: -ge: unary operator expected /tmp/user.scripts/tmpScripts/fan_ipmi_control/script: line 29: [: -le: unary operator expected /tmp/user.scripts/tmpScripts/fan_ipmi_control/script: line 33: [: -le: unary operator expected /tmp/user.scripts/tmpScripts/fan_ipmi_control/script: line 37: [: -le: unary operator expected Script Finished Jun 06, 2022 15:38.21 Any Idea?
  2. Funny thing, I removed the preclear disk pluggin, that apparently was not compatible with Unraid 6.9.2, and it has been 16 hours and everything is working perfectly.... Fingers crossed!
  3. No one else has access. I have some dockers that use internet, namely qbittorrent/teamspeak/YouTube-DL
  4. Bios is not configured to automatically boot, so it did a restart. I always assumed that if a hardware error occorred that shutdown the system, the parity would have to be checked upon starting the array. Replaced all the RAM, same problem. Only thing I noticed, I didn't start the array and it didn't reboot for more than 7 hours. When I started it, always reboot in less than 2 hours.
  5. yes, server webGUI working but array stopped, until this last time. I mean, server could have rebooted, but the array made a clean stop, no parity checking needed. I supposed that if the server just rebooted, the array would do a “dirt” stop and had to be parity checked…
  6. This time yes, the server turned off, made a clean system power down. The other times, only stopped the array.
  7. Just shutdown again, this time I have more logs from JorgeB sugestion. Yes, I have UPS, just disconected the USB and stopped the APC UPS daemon, just in case. syslog-
  8. Hi Since 2 days ago my server keeps stopping the array randomly, last time it was running only 15/20mn and when I tryed to reach a share, it was stopped... No hardware change, no pluggins added, nothing... Please help... alexandria-diagnostics-20220525-1550.zip
  9. Hi I bought a Dell r515 that had a perc H700 (that works perfectly, but in RAID mode) and replace it wit a perc H200, flashed to IT mode, changed from H200A to H200I to work into the dedicated slot through this tutorial The H200 works perfectly in a test computer, but when I put it in the r515 on the decdicated slot, the following error happens: PCIe Degraded Link With Error: Integrated SAS Expected Link Width is x4 Actual Link Width is x2 Every test with the original H700 or putting the H200 in another computer is perfect, so the r515 Raiser and the H200 are working, only not when togheter... I cannot put the H200 in another slot because the cables wont reach it... Any ideas?
  10. Thank you, tomorrow I have to go buy a new flah drive and replace the damaged one
  11. So my unraid server log is full of blk_update_request: critical medium error, dev sda. I'm pretty sure that this is a USB Flash problem, but I wold like to have a second opinion from you guys. Thanks in advance alexandria-diagnostics-20210618-2122.zip
  12. Hi guys I'm new at unraid, just started my Media Server, and I have a doubt (noob probably) So, disk configuration is Parity - 14 TB Western Digital - WDC_WD140EDFZ Disk 1 - 14 TB Western Digital - WDC_WD140EDFZ Disk 2 - 6TB Seagate - ST6000DM003 During the array build, the WD drive reached 190MB, now when I'm moving files from any device, speed is always much lower. Is it normal for the drives (parity and copy targer) to be reading and writing simultaneously, hence droping maximum speed? Attached are 2 prints, one of the share config, the other from disks speed during copy. Thanks Bruno Palhares