master.h

Members
  • Posts

    127
  • Joined

  • Last visited

Everything posted by master.h

  1. I did this exact thing not that long ago. Be default, my motherboard came with IDE enabled. I switched it over to AHCI, and unRAID loaded without a hitch. Write speeds to the cache drive went up as well.
  2. It sounds to me like what happened was brian purchased a new Sony Pro USB, then copied the files from his new USB to his existing basic USB. If that is the case, brian, the key is specific to the USB that you purchased, and will not work on any other USB drive.
  3. Please post the output of: VBoxManage list vms Here it is: root@Saidin:~# VBoxManage list vms "<inaccessible>" {7640ff16-f7ea-46a1-900e-527a2bd11992} "SaidinW7VM" {e7894331-f286-4fe4-b803-f41e060d01f1}
  4. I have an issue where a blank VM is showing up in the settings page (see attachment). I think what happened was I manually deleted the VM folder from its disk location, not using phpvirtualbox. The VM doesn't show up in phpvirtualbox, however. I'm sure it's something simple like deleting a setting or config file somewhere, but I can't for the life of me find it...
  5. It's my cache drive. I have a handful of spare drives laying around. I plan on replacing it when I get home.
  6. Apparently unmenu is still available when booted in safe mode. Smart attributes: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 118 099 006 Pre-fail Always - 185119076 3 Spin_Up_Time 0x0003 099 099 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 159 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 1 7 Seek_Error_Rate 0x000f 083 060 030 Pre-fail Always - 231028177 9 Power_On_Hours 0x0032 073 073 000 Old_age Always - 24206 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 124 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 099 000 Old_age Always - 21 189 High_Fly_Writes 0x003a 001 001 000 Old_age Always - 1014 190 Airflow_Temperature_Cel 0x0022 070 055 045 Old_age Always - 30 (Min/Max 25/31) 194 Temperature_Celsius 0x0022 030 045 000 Old_age Always - 30 (0 19 0 0) 195 Hardware_ECC_Recovered 0x001a 051 031 000 Old_age Always - 185119076 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 270110493269636 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 2411685787 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 534815259
  7. I rebooted in unraid safe mode and limited ram to 4095. Write speeds on average are 6mpbs, peaking at 10. I also re-tested with all my plugins enabled and no memory restriction (running at 4096, as I have one 4GB stick installed) and my copy averages about 30mpbs, fluctuating from 15 up to 50. So it's not very consistent, but it's a lot faster. My normal syslog is too big to be attached, so I've put up links to each syslog in my dropbox folder. https://www.dropbox.com/s/jkasy3c73fhbjxc/syslog-4095-safemode.txt https://www.dropbox.com/s/488t00d8rthamej/syslog-normal-no_ram_restrictions.txt Nothing wrong in the syslogs. How full is your target disk? This is not an -rc16c issue. The disk has 641.69 GB free space, and the share I'm writing to only exists on that disk. The cache drive has 270.7 GB free as well. whats the health status of your cache disk? Currently I'm finishing a parity check. I figured with all the rebooting I've been doing lately, should probably run one. How do I check the health status? The only way I know is to use unmenu, but I'm in safe mode at the moment.
  8. I rebooted in unraid safe mode and limited ram to 4095. Write speeds on average are 6mpbs, peaking at 10. I also re-tested with all my plugins enabled and no memory restriction (running at 4096, as I have one 4GB stick installed) and my copy averages about 30mpbs, fluctuating from 15 up to 50. So it's not very consistent, but it's a lot faster. My normal syslog is too big to be attached, so I've put up links to each syslog in my dropbox folder. https://www.dropbox.com/s/jkasy3c73fhbjxc/syslog-4095-safemode.txt https://www.dropbox.com/s/488t00d8rthamej/syslog-normal-no_ram_restrictions.txt Nothing wrong in the syslogs. How full is your target disk? This is not an -rc16c issue. The disk has 641.69 GB free space, and the share I'm writing to only exists on that disk. The cache drive has 270.7 GB free as well.
  9. I rebooted in unraid safe mode and limited ram to 4095. Write speeds on average are 6mpbs, peaking at 10. I also re-tested with all my plugins enabled and no memory restriction (running at 4096, as I have one 4GB stick installed) and my copy averages about 30mpbs, fluctuating from 15 up to 50. So it's not very consistent, but it's a lot faster. My normal syslog is too big to be attached, so I've put up links to each syslog in my dropbox folder. https://www.dropbox.com/s/jkasy3c73fhbjxc/syslog-4095-safemode.txt https://www.dropbox.com/s/488t00d8rthamej/syslog-normal-no_ram_restrictions.txt
  10. How were file transfers when you first booted RC16c were they good and then went slow after 3 days?? If so just booting up with that mem option may not mean anything as it would be the same as just rebooting you system. Also did you just use the stock menu mem boot option or did you modify it?? Sorry, I should have been more clear. RC16C started up fine, all my plugins worked, and I could copy/stream files with no problems. I didn't notice the slow speed issue because I didn't have anything to copy to my server until my first post. Please repeat experiment on completely stock install. I reverted to stock install with 4096MB ram, speed topped out at 4mbps, and constantly fluctuated from 1mbps up to 4, and frequently dropped to 0. If you want me to try stock with my original 8192MB ram, I'll have to wait until I get home tonight after work. syslog.txt
  11. Yeah. You've got crapload of memory there. Try booting with less than 4095MB of RAM, and then let's see if you'll have a problem. Dropped to 4096 MB RAM, speeds went way up. Thanks for the advice. If you read the release notes there is now a safe boot mode you can select on boot or by having a file on you flash drive so u don't need to rename everyting I knew there was a safe boot mode, but I was at work and my server runs headless anyway, so I couldn't specify that option at boot. I'll have a look at the release notes to find the file you mentioned. Thanks!
  12. I upgraded to RC16c not too long ago, and let it run. Its been running fine for a handful of days, but today when I tried to copy the new Firefall Beta installer to my array, transfer speeds were abysmally slow (maxing out at 10mbps, attached screenshot shows 4mbps). Read speeds are fine, right around 40. I had put in some custom settings for md_num_stripes, md_write_limit, and md_sync_window (just randomly picked some numbers but made sure that num_stripes was equal to write_limit + sync_window), but I reset those to default, renamed all my plugin folders, and rebooted. I'm running stock unraid rc16c (except for unmenu and I forgot to rename my "extra" folder so I have Plex). Any ideas? Syslog attached. syslog.txt
  13. Will do. However, I did copy approximately 100GB yesterday evening, and manually invoked the mover, and all of it transferred successfully, no locking up... strange. I'll post again if it locks up.
  14. I'm on RC-15a. I'm sure it's hardware related, but I'm not sure what the issue is. I can't provide a syslog, as the entire server locks up: no webgui, no unmenu, can't ping, even the console is locked up. Only way to get connectivity back is by rebooting the server. I had tried to create an entry in the crontab to copy out the syslog every x minutes, but apparently I didn't write the entry correctly. How can I automate the backup of the syslog? Does anyone have any ideas why my server could be locking up? Motherboard: ASUS P5N-D http://www.newegg.com/Product/Product.aspx?Item=N82E16813131232 PCI card: Promise Sata300 TX http://www.newegg.com/Product/Product.aspx?Item=N82E16816102065 CPU: Intel Core 2 Duo http://www.newegg.com/Product/Product.aspx?Item=N82E16819115032 RAM: 4GB (4x1GB) Corsair http://www.newegg.com/Product/Product.aspx?Item=N82E16820145590 Power supply: Thermaltake T42 http://www.newegg.com/Product/Product.aspx?Item=N82E16817153023 Hard drives: 1 x http://www.newegg.com/Product/Product.aspx?Item=N82E16822148699 2 x http://www.newegg.com/Product/Product.aspx?Item=N82E16822152106 1 x http://www.newegg.com/Product/Product.aspx?Item=N82E16822136075 3 x http://www.newegg.com/Product/Product.aspx?Item=N82E16822148230 1 x http://www.newegg.com/Product/Product.aspx?Item=N82E16822144415