HK-Steve

Members
  • Posts

    148
  • Joined

  • Last visited

Everything posted by HK-Steve

  1. Thanks binhex, I do know that, BUT, I have always kept the same order, I am a bit insane with my UnRaid towers 😁
  2. Thanks to you both, and who moved the thread. Will remove the hard drives and wrap them individually. Will be sure to take a snap shot of the drive order and serial number before doing so. And a backup of the USB stick. Much appreciated
  3. Hi Everyone, Not sure where to ask, but thought this was the best place to ask. If not, please move. I am moving from Switzerland to UK. Shipping company. Would you remove the hard drives from the Tower's and wrap them individually? Or keep them mounted in each Tower/NAS, In hard drive trays? Tower1 is 6 hard drives, 10Tb Tower2 is 24 hard drives, 78Tb Tower3 is 15 hard drives, 100Tb I also have couple of Qnap and Netgear NAS, about another 132Tb. ..................Yeah, I love my TV and Blu-Ray's. Appreciate your comments and advice. Cheers Steve
  4. The Disk 14 said it had finished the Extended Smart Test, interesting. Glad I have removed both drives from the array. Much appreciated once again. Cheers
  5. Finished the Read-Check with no errors. Here is the Extended Smart Test for Disk 14. Disk 15 would not go past 10% after 10mins, so I stopped the test. So no report for Disk 15. Just powered down and checked the sata and power connectors. Found no problems other than Disk 14 and 15 were very old drives, Seagate Enterprise Capacity v5 Hard drive from 2015. So I removed them from the array. New Config, set all the disks individually as I wrote them down. Now doing a Parity rebuild. Will buy some new 8Tb drives and install next week. Much appreciated the help itimpi, You have helped me learn a little more about UnRaid. tower3-smart-disk14-before.zip
  6. OK, I will wait for the read-check to finish. OR should I stop the read-check?? Will power down and check all the cables. Then run a Smart test on the drives. I will post the Smart test when completed. Much appreciated.
  7. There was a single Folder on both disks, Movies, ready to copy to when I ran out of space on the disk 13. Also there was no activity on the Tower when I set the New Config
  8. Disk 14 and 15 are still red X after the New Config Am 40% through the Read-Check Thanks for looking. tower3-diagnostics-20201012-1635.zip
  9. Thanks itimpi, I followed your steps, steps 1, 2 and 3 no worries. Step 4, went into maintenance mode, did the file system check, that ran through. this is from disk 14 Phase 1 - find and verify superblock... Phase 2 - using internal log - zero log... - scan filesystem freespace and inode maps... sb_fdblocks 1939163355, counted 1952984849 - found root inode chunk Phase 3 - for each AG... - scan (but don't clear) agi unlinked lists... - process known inodes and perform inode discovery... - agno = 0 - agno = 1 - agno = 2 - agno = 3 - agno = 4 - agno = 5 - agno = 6 - agno = 7 - process newly discovered inodes... Phase 4 - check for duplicate blocks... - setting up duplicate extent list... - check for inodes claiming duplicate blocks... - agno = 0 - agno = 1 - agno = 2 - agno = 3 - agno = 4 - agno = 7 - agno = 6 - agno = 5 No modify flag set, skipping phase 5 Phase 6 - check inode connectivity... - traversing filesystem ... - traversal finished ... - moving disconnected inodes to lost+found ... Phase 7 - verify link counts... No modify flag set, skipping filesystem flush and exiting. I could not start correcting parity check, only a Check will start Read-Check of all array disks. Not sure what to do now, Much appreciated.
  10. Hi Everyone, Had a power failure, after my Tower3 was powered up, I have 2x drives with a red X. My other 2x Towers had no issues. I have been rebuilding my workshop, so the UPS was not protecting the Towers unfortunately. Both 8Tb drives have no data, They are about 4 months old approx. What is the next step to take? Last parity check was about 30 days ago, added lots of data to other disks, but not 14 and 15 which have the red X's. Appreciate any advice and help. Thanks Steve tower3-diagnostics-20201011-1413.zip
  11. After messing around for the last couple of hrs, I changed my IP address to automatic, then back to a static IP address after a reboot, and now all is good. Weird, never had that happen before.
  12. Changed port on my Modem, still the same. 😡 Replaced my 16 port switch with a new unit, still the same. Hmmmmmmm Think I will shutdown all my network switches (I have about 10x switches) and repower them and see what happens
  13. No, I reset the modem yesterday, today just can not stay connected. Changed cables and network switch also. Moved Tower to another room and same problem. Thanks for looking and suggestions This Tower3 has been online for a very long time with no issues, strange my other 2x Towers were not effected, running the same UnRaid version
  14. I have exactly the same problem today, Had a problem with my Modem, had to do a factory reset, Now every 2 mins or so, can not access. My other 2x Towers are fine, just my Tower3 which is all my movies. Diags attached tower3-diagnostics-20200830-1518.zip
  15. Yes, within the app on the xbox. Sorry I do not have an xbox, so was a guess to fix. Using the old player fixed my Nvidia Shield.
  16. On your XBox, Go to settings/advanced/player is there a setting for Use Old Video Player?
  17. There were a lot of problems with the new Plex player, I have problems on my Nvidia Shield with the new player. Changed to the old player on the Nvidia Shield and have had no issues since. Maybe it works for you also. My playback would stop every 20mins.
  18. Nice setup, Congrats. CPU temp is high at 73'c, what cooler do you have? You also should replace the SUPERMICRO AOC-SASLP-MV8 PCI-Ex4, LSI are more reliable for UnRaid.
  19. So I changed the network cable, port on the 8 port network switch. Changed the network switch still the same speed. Tomorrow will try a pci-e network card and see what changes
  20. Both Tower 2 and 3 are exactly the same motherboard, cpu. Ram is 32Gb Tower3, 16Gb in Tower2
  21. Yeah, Just tested my Tower2. something definately wrong.
  22. Thanks Johnnie, I tried to run iperf but following SpaceInvaderOne video I could not install. I really am not a linux command person, sorry. Will try to get a speed for you. Searching now for info All 3x of my Towers sit on the same UPS, and same network switch, right next to each other. is weird. Much appreciated