Conson Droppa

If I click on the disk's label (sdd) on the PreClear plug page, I get this info attached:

Tried all sorts of cabling scenarios. Tried new power and SATA cable and new SATA port. Tried swapping with known working power and SATA. I placed a bare 500GB laptop drive on Parity's original power and SATA and it came up as it should under "unassigned". I do notice now with the Parity drive plugged in and my head inside the case, when I power up, I can hear some platter/head squeaks. I'm going to assume the drive is failing and keep it powered down until my new drive arrives on the 7th. Unless there is anything else I can look into. Why can I see it under the pre clear plugin but not under unassigned?

I swapped parity and disk1 SATA cables earlier but I will replace it totally right now. I'll try a different power wire too and report back in a minute.

This is an older disk screenshot but nothing had changed since.

Diag - Sorry, had it and forgot it. unraid-diagnostics-20161205-1848.zip

On Dec, 1st my server ran it's monthly parity check and emailed me that it had 20 errors. So I ran it again and a few hours later it returned no errors. I went about my day. I log on to the GUI today and I see the orange triangle saying array is unprotected and noticed my Parity disk is missing. When I stop the array it is not an unassigned disk. I tried a different SATA and power cable. No luck. I can't pull its SMART either. The weird part is, a disk with it's serial number shows up in the pre clear plugin page. I attached an image below. To make things even stranger to me, it reports a size of 4.14 GB for a 2TB drive. Is this normal? Can I hit the pre clear button and see if things right itself. I logged in via terminal and ran the df and lsblk commands and don't see a drive with 'sdd' as it's label. I just ordered a new 4TB disk for my parity replacement but it won't be here until Wednesday. I would like to protect my array somewhat until it arrives. unRaid - 6.2.4 (going update sig) Thanks in advance.

No, 2 are plain instances of vanilla minecraft. Nothing added or taken away. After hitting start on each they go green play button on the docker icon for about 10 seconds then go red stop button. I'll grab and compare the logs of each when I get home and post them. Sent from my iPhone using Tapatalk

Can someone shed some light on how to maybe correct this. It is happening to all my instances of McMyAdmin. Log for one of the dockers below. *** Running /etc/my_init.d/20_apt_update.sh... finding fastest mirror Getting list of mirrors...done. Testing latency to mirror(s) Getting list of launchpad URLs...done. Looking up 3 status(es) 1. pubmirrors.dal.corespace.com (current) Latency: 45.53 ms Org: Corespace Status: Up to date Speed: 1 Gbps 2. reflector.westga.edu Latency: 50.18 ms Org: University of West Georgia Status: Up to date Speed: 45 Mbps 3. mirrors.wikimedia.org Latency: 51.00 ms Org: Wikimedia Foundation Status: Up to date Speed: 10 Gbps pubmirrors.dal.corespace.com (current) is the currently used mirror. Skipping file generation We are now refreshing packages from apt repositories, this *may* take a while Ign http://pubmirrors.dal.corespace.com trusty InRelease Get:1 http://pubmirrors.dal.corespace.com trusty-updates InRelease [65.9 kB] Hit http://ppa.launchpad.net trusty InRelease Hit http://ppa.launchpad.net trusty/main amd64 Packages Get:2 http://pubmirrors.dal.corespace.com trusty-security InRelease [65.9 kB] Hit http://pubmirrors.dal.corespace.com trusty Release.gpg Get:3 http://pubmirrors.dal.corespace.com trusty-updates/main Sources [476 kB] Get:4 http://pubmirrors.dal.corespace.com trusty-updates/restricted Sources [5,921 B] Get:5 http://pubmirrors.dal.corespace.com trusty-updates/universe Sources [214 kB] Get:6 http://pubmirrors.dal.corespace.com trusty-updates/multiverse Sources [7,374 B] Get:7 http://pubmirrors.dal.corespace.com trusty-updates/main amd64 Packages [1,139 kB] Get:8 http://pubmirrors.dal.corespace.com trusty-updates/restricted amd64 Packages [20.4 kB] Get:9 http://pubmirrors.dal.corespace.com trusty-updates/universe amd64 Packages [502 kB] Get:10 http://pubmirrors.dal.corespace.com trusty-updates/multiverse amd64 Packages [15.2 kB] Get:11 http://pubmirrors.dal.corespace.com trusty-security/main Sources [153 kB] Get:12 http://pubmirrors.dal.corespace.com trusty-security/restricted Sources [4,621 B] Get:13 http://pubmirrors.dal.corespace.com trusty-security/universe Sources [53.2 kB] Get:14 http://pubmirrors.dal.corespace.com trusty-security/multiverse Sources [3,021 B] Get:15 http://pubmirrors.dal.corespace.com trusty-security/main amd64 Packages [675 kB] Get:16 http://pubmirrors.dal.corespace.com trusty-security/restricted amd64 Packages [17.0 kB] Get:17 http://pubmirrors.dal.corespace.com trusty-security/universe amd64 Packages [185 kB] Get:18 http://pubmirrors.dal.corespace.com trusty-security/multiverse amd64 Packages [4,015 B] Hit http://pubmirrors.dal.corespace.com trusty Release Hit http://pubmirrors.dal.corespace.com trusty/main Sources Hit http://pubmirrors.dal.corespace.com trusty/restricted Sources Hit http://pubmirrors.dal.corespace.com trusty/universe Sources Hit http://pubmirrors.dal.corespace.com trusty/multiverse Sources Hit http://pubmirrors.dal.corespace.com trusty/main amd64 Packages Hit http://pubmirrors.dal.corespace.com trusty/restricted amd64 Packages Hit http://pubmirrors.dal.corespace.com trusty/universe amd64 Packages Hit http://pubmirrors.dal.corespace.com trusty/multiverse amd64 Packages E: dpkg was interrupted, you must manually run 'dpkg --configure -a' to correct the problem. Fetched 3,606 kB in 16s (217 kB/s) E: dpkg was interrupted, you must manually run 'dpkg --configure -a' to correct the problem. *** /etc/my_init.d/20_apt_update.sh failed with status 100 *** Killing all processes...

Says mounted by Mini, that is the name of this Mac Mini Last login: Sat Oct 15 18:32:04 on console Mac-Mini:~ Mini$ mount /dev/disk1 on / (hfs, local, journaled) devfs on /dev (devfs, local, nobrowse) map -hosts on /net (autofs, nosuid, automounted, nobrowse) map auto_home on /home (autofs, automounted, nobrowse) /dev/disk2s2 on /Volumes/Time Machine (hfs, local, nodev, nosuid, journaled) //[email protected]/Libraries on /Volumes/Libraries (smbfs, nodev, nosuid, mounted by Mini) Mac-Mini:~ Mini$

Upgrade Spigot to latest Minecraft Build (The way I did it for 1.10.2) FYI for users of this Docker I though i would share the way I upgraded one of my McMyAdmin Dockers to Spigot 1.10.2. It may be the long way around or overkill but it worked. There is very little info out there to do this. Even on Spigot and McMyAdmin forums. Maybe a McMyAdmin 3 (Amp) Docker will solve this. But I think Amp is like docker. Not sure, never looked into it. May be redundant to run a framework in a framework. As discussed earlier, McMyAdmin 2 will only self build Vanilla minecraft, no forks. Also, I am not sure how to, or if it is possible to run the BuildTools.jar directly in the unRaid environment. So I did the following to bypass this. BACKUP WOLRD(S)/NETHER/THE END FOLDERS Setup Spigot as if I was going to run the server on my Mac. - Made a Spigot directory on mac - downloaded and ran Buildtools.jar - started serve on mac - accepted EULA.txt file - joined server via Minecraft client in case any files needed to be built. (not sure if needed) - logged off server - stopped server On unRaid - stopped particular McMyAdmin docker running Spigot - navigated to minecraft folder in the AppData/McMyAdmin folder (or whatever you named it) - copied/merged/replaced files and folders which are highlighted in the attached screenshot - renamed file spigot_x.xx.x to spigot.jar as that is what is required. I examined each file and folder minecraft created and uses and I am not sure if I copied too much, too little or just the right ones but it worked great. This allowed me to go from 1.9.2 to 1.10.2. In the future Microsoft/Mojang/Spigot may change file/folder tree architecture which may break this method. Proceed at your own risk and make good backups before attempting.

@speeding_ant I have an unrelated/related situation I need your input on. As you know I have used the script forever and switched to Sierra and Margarita mounting. I have 2 shares I mount on all devices, "Libraries" and "unRaid". Since I had that stale mount issue we discussed earlier, my "Libraries" share has been double/duplicate mounting. It was also that share that was stale. Things I have done and checked: - deleted all script files and folders - used AppCleaner to remove Margarita and reinstalled (all files, folders, and nz.co.pixeleyes files) - I am only exporting SMB I do not think it is Margarita doing it, I just need some direction on where I can look to see what is mounting it. It's almost like "Finder/Connect To Server" is remembering to do it itself. I have attached screenshots of mounts and Margarita's container folder you directed me to last time. Thanks ahead, any input greatly appreciated.

From the little bit I know, I assume if you have a "Open WebGUI" button, you're using the Docker and not the plug-in. I use the plug-in version and always just manually went to "ipaddress:6237" when needing to use unBalance" I believe the plug-in version was recommended a few months back for permission and disk access reasons. However, for the particular question you asked, I don't know the answer to that. Sent from my iPhone using Tapatalk

Refer to my post and speeding-ant's reply at the end of 09/18/2016 and see if that resolves your issue. Sent from my iPhone using Tapatalk

In my situation my whole home/family environment is Apple/Mac/Apple TV/iPad/iPhone/Airports, so I use iTunes extensively for organization and device syncing and home sharing to bedrooms. I use Plex for those spur of the moment Movie or TV shows I want to see and I don't have it synced to my device on hand. And also for Mom and Dad to watch from their Roku at their house. I explain this first because I just point my folder mappings to the individual folders in my iTunes Media folder. They are sort of pre-organized for me to begin wth. You can see in the photo I attached. It may look slightly different if you are still on 6.1.X, photo is from 6.2, but its the same setup basically. Just make up some container paths (/TV - /HomeMovies - /Concerts - /Documentaries) and point to where that data is going to be or currently stored. Then once that's done, in Plex, you can create a library for each container path you created. So when you create a Plex library called TV Shows you can point it to the container path /TV or whatever you created. If your folder setup is not based on iTunes as mine are, just organize them how you already do, and point to those folders.

No, cheers to you. Easiest unRaid problem/fix I have ever had.

Nope, Empty. unRaid folder/mount is as though I am browsing it. All files are there.

This is here because you can't have an empty message body

Even though it's mounted. EDIT: Oh, BTW this is a Sierra machine.

Can you maybe explain this. Giving me that error when I hit the mount button. Tried unmounting everything and starting over. Tried restarting mac. The disk area button says "Mount" and not "Eject" like my unRaid share.

IMO i like them all. Docker Image Alerts come across as a notice I believe. Even though it's overkill, I like knowing everything that's going on. I even like being notified of app updates in case there is a problem I can remember/recall that that app updated very recently. Strictly my opinion though. Sent from my iPhone using Tapatalk

I like that, It would give a better chance of seeing higher priority notifications. I sometimes miss the email ones coming through when I'm busy at work. I have a slight panic attack when I look back at them later and see a UPS warning came in. Not to mention, unRaid has been so rock solid for the last few years that only the "PASS" email comes through. I'm sure whatever you decide will work for us though. If not someone will tell you. Sent from my iPhone using Tapatalk

May I request a confirmation dialog for the "Start Parity Sync" button. I've started parity sync twice tonight playing with the app. I know it's my clumsiness but an "Are you Sure" button would be great. Sent from my iPhone using Tapatalk

That is correct - just delete those two files. Cheers. Any chance the iTunes functions from the script will show up here? That's 99% of the reason I run it. Also, I think something in OS X Sierra GM broke something. It only mounts my first share listed. I will see how it performs with official release. Been using this script flawlessly since you uploaded it, great work. And, as I've told you before Great work on all the Margarita forks. Correct me if I am wrong but I guess I could leave the mounting up to Margarita and still use the iTunes portion of the script?

That is correct - just delete those two files. Cheers. Any chance the iTunes functions from the script will show up here? That's 99% of the reason I run it. Also, I think something in OS X Sierra GM broke something. It only mounts my first share listed. I will see how it performs with official release. Been using this script flawlessly since you uploaded it, great work. And, as I've told you before Great work on all the Margarita forks.

Wow, I feel so stupid, I've used that method before. I knew I posted that question to soon. It was right in front of me.