BillPlott

How long should I expect the FileSystem Check to take? Currently it's been over 90 minutes. Status: Phase 1 - find and verify superblock... couldn't verify primary superblock - not enough secondary superblocks with matching geometry !!! attempting to find secondary superblock... .found candidate secondary superblock... unable to verify superblock, continuing... unable to verify superblock, continuing...

ok - Cancelling Rebuild and will do a File System Check

So, My steps would be to: - Stop Current Rebuild - Perform File System Check - Upload new Diagnostics I'm also a bit thrown off that Disk 2 became corrupt when it was rebuilt/replaced last week and I only touched Disk 1 last night to replace it. I do still have the option to replace Disk 1 with the old 8TB drive if that helps my scenario.

If Disk 1 finishes rebuilding, can't Disk 2 (Rebuilt last week) be rebuilt again without issue? Should I replace the new disk with the old one and let a parity check happen, then try replacing it again?

Disk 1 is the one being rebuilt from 8TB to 12TB currently - has a couple more days til it's finished before I can reboot. I can wait til then, then post the logs and determine next steps.

I recently rebuilt/upgraded a 4TB drive to 12TB without issues and am doing the same thing with an 8TB drive to 12TB, but after assigning the new drive and starting the array, the previous drive says "Unmountable: wrong or no file system". Wondering on next steps as the new drive is being re-built and the Array Operation section says Unmountable disk present: Disk 2 and gives me the option to Format. I believe my best option is waiting for the re-build to finish on the new disk, then format the "Unmountable" disk which was just re-built last week but looking for options and what this really means and why it might have happened. Prior to adding the newest disk, the newly built disk had no issues. tower-diagnostics-20250324-1943.zip

I can't seem to get either solution to work for my issue Plex database error in logs: Starting Plex Media Server. Error: Unable to set up server: sqlite3_statement_backend::loadOne: database disk image is malformed (N4soci10soci_errorE) when running ./DBRepair.sh I receive the error below: root@Tower:~# ./DBRepair.sh bash: ./DBRepair.sh: /bin/sh^M: bad interpreter: No such file or directory I’ve also tried to follow SpaceInvader One’s video, but get the below error when trying to run Plex SQLite root@Tower:/mnt/cache/appdata/plex-sqlite/plexmediaserver# ls CrashUploader* Plex\ DLNA\ Server* Plex\ Media\ Scanner* Plex\ Relay* Plex\ Script\ Host* Plex\ Tuner\ Service* etc/ Plex\ Commercial\ Skipper* Plex\ Media\ Fingerprinter* Plex\ Media\ Server* Plex\ SQLite* Plex\ Transcoder* Resources/ lib/ root@Tower:/mnt/cache/appdata/plex-sqlite/plexmediaserver# “Plex SQLite” “$DB” “PRAGMA integrity_check” bash: Plex SQLite: command not found any other suggestions?

When trying to launch WebUI of docker apps, I keep receiving the below error: The connection was reset The connection to the server was reset while the page was loading. The site could be temporarily unavailable or too busy. Try again in a few moments. If you are unable to load any pages, check your computer’s network connection. If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web. I am fairly new to Unraid, and setup my Plex server for testing 3 days ago, tested streaming a short video from my xbox, and remotely, then the next day, I can't access the UI on any apps. I was attempting to setup a vpn container, but have been unsuccessful. The issue seems to be only when the VPN docker app has VPN_Enabled=Yes. When VPN is not enabled, the Web UI works as expected. I have used ExpressVPN and PIA, but both fail. I can run diagnostics or attach logs as needed.