MyNameWasTaken

So just to clarify you’re thinking it’s something up with the mobo that results in unraid going unresponsive and ultimately the pc is rebooting because of it? Not one of the drives?

It is on a UPS and BIOS is not set to power on after a power restore. The server rebooted itself.

Rebooted again this morning halfway through parity check and now one of the parity drives went to disabled status sydneycarton-diagnostics-20250408-0555.zip

Yes the realtek is being used, the onboard intel was giving the errors and causing me to lose connection all the time

I just got this ehternet card a few months back because the port on my mobo died. I felt like maybe those errors were a result of the OS not recognizing it correctly during some kind of panic it was having? Idk

Having some weird behavior on my server since early this morning. Last night at some point my server rebooted and when it came back up both parity drives showed as disabled. I stopped my array, unassigned the parities, started my array, stopped again, re-assigned them, started array and let the parity check get going. After 5% was complete I noticed the GUI went unresponsive and my terminal window connected to my server was giving some funky errors. Luckily I was able to use "parity.check Pause" and then "powerdown -r" successfully. When the server came back up and I logged in it said my flash drive was corrupt. I don't think that's especially likely since I just replaced my flash drive a few months ago but fine, I downloaded a backup and then powered down and changed the USB port just in case that would help. Powered back up, started the array, and the name of the server had reset to "Tower" but all other prefs are unchanged, array assignments still intact, parity check progress is even remembered. No error about the flash drive either. I changed the name back and started the array back up. I am jumpy now that something is wrong. Attaching diags to see if anyone could take a look and see if there is stuff indicative of issues. I've also got logs from the flash drive from the reboots I've done this morning sydneycarton-diagnostics-20250407-1121.zip sydneycarton-diagnostics-20250407-1020.zip sydneycarton-diagnostics-20250407-1115.zip

I did run a memtest and all was fine. I will scrub the pool. The NIC is the mobo integrated one. I will have to order one to put in and test with.

As best I can tell my server is dropping off network at random times and I cannot for the life of me figure out why. I initially thought the flash drive was the issue but I moved to a new flash drive and also tried updating to current Unraid OS but the same thing keeps happening. The same thing also happens when I initiate a parity check. Luckily the check continues and I can run terminal commands when I attach a monitor to the tower but when the parity check finishes I have to reboot to once again access the server. Attaching diags here and syslog as I started mirroring it to flash to try and capture wtf is going on. sydneycarton-diagnostics-20240919-1728.zip syslog

Would love some input for either how to achieve what I want to do or a better suggestion of how to achieve the same thing. I have 2 ISPs. One is Starlink and the other is a local ISP in my area. I have 2 NICs on my server and I’d like to use Starlink for my arr apps and download clients associated with them. I would like to use my local ISP for hosting plex and have that network in the house for all other devices. Starlink DL speed is much better than my local ISP but does not allow plex outside, hence the split. Thanks for looking. edit to mention: I don’t want to use Starlink as my housewide network because when I tried replacing my local ISP on my mesh network every connection suddenly got real slow. Seems like the more devices on the network the worse Starlink performs

The new disk is not new. It's an old parity I've added to the array. And newly added data isn't going to be accessed any more frequently than older data so I don't need it to be faster. I'd rather equalize the amounts so all drives perform comparably

Forgive me for ignorance but would this be the right app to use if I just want to rebalance all the data on my array after adding a new disk? i.e. I have 6 disks that are 97% full and I want a bit of data from each to shift to this new empty drive. Can this app do that simply? If not simply, then at all?

Just updated the docker container and now cannot get the interface to load. Just get a black screen. Tried Brave, Edge, Chrome, Firefox. Looks like VNC connects but nothing is rendering. Any suggestions? I reverted back to 6.29.0 and no issues so it must be the 7.0.0 image

Please don't mind me, everyone. I'm just a f***ing idiot. After I ran memtest I also updated my BIOS and that reset the clock. I corrected the time and everything is working. I'm going to go die of embarrassment now.

I grabbed the config folder before I overwrote my current flash but I’m not sure if it’s something in there causing issues.

Okay. If that works I need to transfer my key, right?

Well that’s good at least

I was having tons of issues getting the OS to load, tried with a fresh setup on the same flash drive but just sits here and gets nowhere. Memtest all day yesterday tells me all the RAM is fine, not sure if all the data on my array is lost but I can’t even get the OS to load at this point.

Thanks a lot for all the replies it’s been very helpful and educational. I’ve got a memtest going now.

Okay thank you for pointing that out so I can maybe recognize it in the future. What do you suggest? Run memtest again to verify the ram and if that passes flip that BIOS setting or adjust c states like in your linked comment? I ran data scrubbing and didn’t find any errors on the cache. Are those drives maybe the issue and need to be replaced? I just got them so they’d definitely be under warranty.

I'm not aware of any overclocked RAM. I made no changes to overclock it out of the box. It's just ddr5-5600 ram with a ryzen 7950x so it might seem like the 5600mhz is overclocked. Does it say somewhere in the diags it's overclocked? Where are you seeing that?

Yes I can attach files now. Thanks. Here are the most recent diags as well as the syslog leading up to the most recent event tower-diagnostics-20230124-0924.zip syslog.txt

This has happened several times now in the past few weeks and I can't figure out a commonality in all the shutdowns so I've come here for help. My server will become unresponsive randomly. When it does this it doesn't shut the PC down but I also can no longer reach it on my network. Somehow it kills my network and I can't get anything back online until I unplug the ethernet either on the tower or on the switch. I can plug it back in after that and everything is fine on my network but I still can't reach my tower and the only way to get it back is a hard reboot. I tried plugging an HDMI into a monitor when it's in this state but I haven't been able to get picture out of the tower past the splash screen ever since I set it up so I didn't think much of it. I tried changing some configs on it, I installed the fix common problems plugin and implemented all the suggestions. It's a very recent build with all new components that I tested thoroughly before assembling. I am at a loss so I started getting the log copied to flash and when it crashed most recently I grabbed the logs and could use some help deciphering what useful info there may be. I don't see a way to attach files to this post so if someone can let me know how to do that or if I need to just copy it to a pastebin I'd appreciate it.