youngvader

Thank you for this

Hello anyone can help? thanks

Hi, Here you go. Hope you could provide assistance on how should I solve this issue. tower-diagnostics-20231203-0019.zip

Hello again, I have started the rebuild process using a new disk but the speed is extremely slow. it's less than 1MB/sec and it will take 2-3 months to finish. Should I stop this and try again?

Thank you very much. I will give it a go after I have a replacement disk available.

Yes you are correct, is it disk 6 that is missing. I will check all SATA cables. I may have a replacement disk but will require me some moving around because it's a bigger capacity disk. So I will need to transfer my 8TB to a 14TB then use 8TB as the replacement disk. Will I need to manually copy the contents of disk 6 to an external HD first prior to rebuild to ensure that the files won't get lost? Thank you for the instruction. A few other questions. Is it ideal for me to still use my server while I sort out these issues? also the link you shared above is the steps to rebuild if I will use the same disk, but what if I will use a replacement disk? To replace a failed disk or disks: Stop the array. Power down the unit. Replace the failed disk(s) with a new one(s). Power up the unit. Assign the replacement disk(s) using the Unraid webGui <-- Do I assign the replacement disk on the same disk # as the failed disk? Many thanks for your assistance

Hi, Diagnostics also uploaded. Thanks

Hello, would like to ask for assistance with this issue I have. this is my first encountering this issue and to avoid any mistake on my part I hope somebody can please direct me on what should I do next. Do I need to turn off my server now and replace the hard disk immediately with a new one? will it rebuild by itself? Attaching syslog files, hope this proves useful Regards,syslog-192.168.10.82.log tower-diagnostics-20231130-2057.zip

Thank you for the lengthy explanation. Much appreciated

Thanks for your reply. I'm very new to Unraid so apologies but not sure what Jumbo frames and port multiplier you are referring to. I will read up on google. thanks

sorry not sure how to answer this question. The diagnostics file I already posted in my earlier post. May I know what diags you are referring to?

Thanks. I'll wait for feedback

Thanks for your input. Gui has become very sluggish and only way to get it to work is to somehow be able to pause the transfer by clicking the pause and hope that it will register the command during very slow gui. any solution to this issue?

Hi, Please find attached. I hope this is the file you need tower-diagnostics-20230730-2138.zip

Hello, I have an i7-7700 processor and I cannot figure out why transferring 6TB files using Krusader/MC max my CPU to 100%. The disk has just been pre-cleared with no issues so I formatted it to NTFS to begin transfer. But I cannot get it to work because of the constant high usage. Note the issue starts very early and my most recent test using MC I was less than 5 mins of the transfer and my CPU already maxing out. Any help greatly appreciated

I followed a guide and I think that what it did by mapping it to the RAM thanks.

I'm reading up now on setting up transcode folder which I probably don't have. That is most probably why I'm getting the warning

Hi again, I got the docker utilization warning again but looking at the container size nothing is getting larger.

I was able to delete it but turning off all dockers and then using MC instead of Krusader. Thanks for the help. As for your previous message on plex transcoding that it is very likely to be the case because I am not familiar with the location internal/external and I have not changed anything from initial setup. I will look at previous post in this forum for a tutorial on how to do this. Thanks for the help

Thank you for your reply. Apologies but I'm very new with this. Can you guide me where I should change this? What exactly am I looking for that I need to change? thanks

Hello, Trying to move docker and libvirt folder from disk1 to cache. When trying to move it I get this information in syslog. Will it be safe for me to delete the files in disk1? I was getting notification of high utilization in docker.img while using plex Jul 30 17:03:49 Tower move: file: /mnt/disk1/system/docker/docker.img Jul 30 17:03:49 Tower move: move_object: /mnt/disk1/system/docker/docker.img File exists Jul 30 17:03:49 Tower move: file: /mnt/disk1/system/libvirt/libvirt.img Jul 30 17:03:49 Tower move: move_object: /mnt/disk1/system/libvirt/libvirt.img File exists Jul 30 17:03:49 Tower root: mover: finished Thank you in advance for the assistance

Thank you for your help. I hope there are others out there that have other possible solutions.

Server become unresponsive again just now during parity sync. Attaching syslog server syslog-192.168.10.82-3.log

I have included the syslog server and copied it together with my original post. Unless i’m mistaken and its incomplete.

I hope someone can help us. It’s frustrating that I still don’t have parity because of this issue.