heroic-barstool8121

I use NZB.nu as an indexer and SABNZBD as a download client. Everything is Binhex's dockers. When I put 'Test' on the indexer it gives a green check mark but then right when I click on a file to download it immediately fails and gives these three errors. All indexers are unavailable due to failures for more than 6 hours All search-capable indexers are temporarily unavailable due to recent indexer errors All rss-capable indexers are temporarily unavailable due to recent indexer errors It was working last night - given SABNZBD failed almost every download due to missing articles - So I don't see why it would stop working all of the sudden. I've restarted all containers and deleted / setup NZB.nu again with no luck.

I agree, it doesn't seem like sab is the problem. NZB.NU is a Newznab indexer. Maybe their site is down? pretty strange

I use NZB.nu as an indexer and SABNZBD as a download client. Everything is Binhex's dockers. When I put 'Test' on the indexer it gives a green check mark but then right when I click on a file to download it immediately fails and gives these three errors. All indexers are unavailable due to failures for more than 6 hours All search-capable indexers are temporarily unavailable due to recent indexer errors All rss-capable indexers are temporarily unavailable due to recent indexer errors It was working last night - given SABNZBD failed almost every download due to missing articles - So I don't see why it would stop working all of the sudden. I've restarted all containers and deleted / setup NZB.nu again with no luck.

Hello there, I followed SpaceInvaderOne's video on dumping VBIOS for Windows 11 VM. I have VT-D enabled on my MSI Motherboard (i9-12900K). Everything is working, I have my Graphics card enabled through the system devices and it shows up when setting up the Windowsdows 11 VM. The only issue is that there is no place to select VNC when clicking on the VM. It works with the Windows 10 Vm that I also have set up but that is with a virtual graphics card so I know that It is a setting to do with the actual 4060 TI. Upon plugging in a monitor to the Graphics card I saw that it was also getting help on on this error - VT-D Active for GFX Access. I looked through a few Unraid support forums and ran these two command to get that issue fixed. echo "options i915 enable_dc=0" >> /boot/config/modprobe.d/i915.conf echo "blacklist i915" > /boot/config/modprobe.d/i915.conf Upon rebooting that was no longer hanging up and it allowed me to get all of the way past startup but not it is on a grey screen with a small _ on the top left corner when it is support to load into UNRAID GUI. I think that these two issues are related but am unable to find the issue with my limited knowledge. excalibur-diagnostics-20230912-2240.zip

I cannot install Windows 11 at all. Whenever I start up the VM and hit any key it immediately loads into recovery. It doesn't matter if its running i440fx-7.1 or Q35-7.1 ---- OVMR TPM or OVMR bios. I'm trying to load it onto my NVME WD black Cache which is ZFS and 2x 1tb in total if that matters. The OS install ISO is straight from microsoft, downloaded an hour ago.

Thank you so much, this never even crossed my mind since one of my 2 x 16 packs from microcenter was new and the other was used and I double checked with them that it was fully tested (half off so i thought it would be a good deal). After installing a memtest USB bootable one of the sticks failed after about 10 seconds which happened to be the open box one. Pretty annoying that if microcenter actually ram a memtest they would've noticed this but oh well... 2 hour drive for me tomorrow. Everything is booting up great now and very snappy.

My server is constantly crashing and running slow on me. I use the port 192.168.8.249 (static) and when I first turn on the server, it'll be running fine, I can load up any setting and docker. I've been trying to run a parity check for days now but after a bit of use, (it could be 3 minutes or 3 hours, it really just depends on how many times I switch from settings -> docker -> vm tab) it'll crash on me. Most of the time I'm stuck on the apps tab with nothing ever loading in, It I open a new tab (Firefox) it'll work then something else won't load. I then go to Microsoft edge and it'll work again for about a minute then the whole IP won't be reachable on anything and I have to hard reset to ever get it fixed. I left it in this state overnights and I still couldn't reach the IP the next morning. This is a brand new build and configuration, the only part I'm reusing from my old server is the Ethernet cable (since I know it works) and the USB (new config folder). I also have no dockers or VMs running, the open pluggins that I have are Unassigned devices, Community applications and Nvidia. Also, whenever I manage to run a partity sync it shows almost 5000 Sync errors corrected at around 3% done. Here are my parts CPU - I9-12900k 64GB G.SKILL DDR5 6000 PNY 4060 512 Inland 2.5 SSD (Secondary Cache) x2 WD Black m.2 nvme running in raid0 (Main Cache) x2 14tb Seagate EXO (manufacturers refurbished from serverpartdeals.com) 1000W PSU Gigabyte B650 MOBO excalibur-diagnostics-20230909-2222.zip