robst3

Hi, Fresh install of 6.0-b9. Trying to install this Transmission plugin. Have placed transmission.64bit.plg into /boot/config/plugins and rebooted but no Transmission icon in settings page. Tried manually installing with installplg transmission.64bit.plg and get the following: root@Tower:/boot/config/plugins# installplg transmission.64bit.plg plugin: installing: transmission.64bit.plg plugin: creating: /tmp/chk-network - from INLINE content plugin: running: /tmp/chk-network plugin: creating: /boot/packages/libevent-2.0.21-x86_64-1.txz - downloading from URL http://slackware.cs.utah.edu/pub/slackware/slackware64-14.1/slackware64/l/libevent-2.0.21-x86_641.txz plugin: wget: http://slackware.cs.utah.edu/pub/slackware/slackware64-14.1/slackware64/l/libevent-2.0.21-x86_64-1.txz retval: 4 Still no Transmission icon in settings page, and transmission.64bit.plg has been moved to /boot/config/plugins-error. please help!

Tried changing from "nobody" to "root" but no success.

Thanks! I ended up deleting all the <MD5> .. </MD5> lines for all packages in the plugin, as was throwing up that same error for each package. I now have the deluge settings page on webui, but cannot get it to start. At one point after hitting the start button the status at bottom left displays the following message. not sure if that has anything to do with it? 12345667891011deluged.pid not created for some reason... OK I have set install directory to /mnt/disk1/apps/deluge and left port as default...

Hi I am trying to install this Deluge plugin on Unraid 6.0-beta5a. I followed steps 1 and 2 in the first post of this thread with no problems. After typing in the following via telnet as per step 3: installplg /boot/config/plugins/deluge_64.plg I get the following error: plugin: creating: /boot/packages/deluge-1.3.6-x86_64-1ponce.txz - downloading from URL http://ponce.cc/slackware/slackware64-14.1/packages/deluge-1.3.6-x86_64-1ponce.txz plugin: checking: /boot/packages/deluge-1.3.6-x86_64-1ponce.txz - MD5 plugin: bad file MD5: /boot/packages/deluge-1.3.6-x86_64-1ponce.txz Can anyone help? Thanks

Hello! This is my first attempt at building an unraid server, so apologies for the dumb questions. I have followed the wiki and seemed to have everything up and running (parity sync done and drives formatted). After rebooting the server there was a red blob next to one of the hard drives. I used initconfig to reset the array and rebooted again - this time I noticed "Buffer I/O error on device sde" flashing up as unraid booted. I looked in the syslog and there are a number of other errors all related to this drive. I have tried switching mobo SATA ports, SATA cable and power cable but that did not resolve the problem... I performed a 3 cycle preclear on the disk when I added it and they came back fine. I have tried preclearing again and it is going incredibly slow (2.1MB/s on the pre-read). I have attached the syslog and the original preclear report. I'd really appreciate some expert advice on this! The server specs: Mobo: Asus P6T-SE CPU: i7 920 RAM: 3GB DDR3 1333 PSU: Corsair CX430 HDD1: 3TB Seagate barracuda ST3000DM001 HDD2: 2TB Samsung Spinpoint F4 HD204UI HDD3: 1TB Samsung Spinpoint F3 HD103SJ (the problem disk...) HDD4: 500GB Seagate barracuda ST3500418AS Thanks, Rob preclear.txt syslog.txt