crazyc

For clarity reasons i can say that the new version works as expected with v7.2.4. Update driver package and restarted server, all working, no issues with install or update.. Note I have not updated to v7.2.5 as of yet

thanks @ich777 Update is there waiting. Will need to wait for immich to finish processing then will update. I am still V7.2.4 for the moment

Have not updated to v7.2.5 as yet. May wait until any bugs are sorted. I notice in my plugins page it shows the nvidia driver as 2026.03.19 and status not available. It says i am running Nvidia Driver Version 595.71.05 and everything is working well. As far as 2025.05.01 i cannot see that...any pointers to where or how i can update

interesting, many thanks. I have seen this in a few posts pointing to ecc memory errors..will dig deeper

Anyone ? Would appreciate some guidance

Hey I am building an Old HP Z620 and all was working fine for a few days. I then came across the above error. It then dropped one of my sata drives, checked the drive and it was fine but not showing in unraid or system bios. Reseated same error then replaced the sata cable and same thing, moved it to a different port and drive reappeared. Error came up again and cleared. I think i have a dead port or a dying drive. I have attached the diagnostic form when i changed ports and the error showed. Can anybody confirm or assist for me please, I am not sure what I am looking for. crazytower-diagnostics-20260402-1711.zip

All good, actually got 22hrs before it dropped the gpu...Will start prepping some parts to test

Thank you. I got a solid 2 1/2 hours before it dropped this time. I have another Mobo and CPU and Memory that i can test when time permits. This is frustrating

Quick question whiich driver do you recommend for my 4060ti, the production or latest V595.58.03 or the open source v590.48.01 ?

so strange , reboot server brings it back to life...Nothing that i am aware of that calls nvidia-smi. I have Homepage on another server that shows a few container statuses on this one . I will have to see if i can check the hardware, The PSU is a 1200w device about 6 months old. I need to do some outside then will come back and attempt reseating everything. This issue has only just started yesterday I do have another motherboard and ram. At a loss but trial and error I guess. Now that I think of it Unmanic had an update maybe 1 to 2 days aga and i have been using it each tim the gpu dropped. Ity just had another update may see if it is anything there, could be grasping at straws Thanks again

I woke to nvtop saying no GPU and nvidia-smi no devices found it does show under system devices. Any thing different this time in the Diagnocrazytower-diagnostics-20260328-0917.zipstics ?

As i said i hope it is just a Friday.. GU and PSU are less than 2 years old. Mobo, cpu and ram are 5-7 years at least....as always working fine until they are not.. This time around with Monitor attached Cpu Stats removes and NVtop install current uptime 1hr 6 min happily compressing with unmanic. One more glass of red the =bed and see what happens tomorrow, Will move back to hdmi dummy plug and see what happens

So have removed Dummy Hdmi and reconnected monitor. Have removed gpu stats and loaded NVtop instead will see how long this last. Wonder if the old motherboard has finally bit the dust or is it just Friday ? I am Lost..

1hr 49m uptime and dropped gpu yet again again..should i try nvtop instead of gpu stats..some reading has pointed to this crazytower-diagnostics-20260327-2155.zip

Thanks @ich777 Will check out the bios, it has been untouched for several years. I connected the monitor and after a reboot it worked. I then reconnected the HDMI dummy and it worked I will "add nvidia-persistenced at the very end to your go file" Very new to unraid so will work that one out. And wow with the errors.. Many thanks for your prompt assistance After adding the nvidia-persistenced it semes to have fallen off again while transcoding or it could of been me editing the file. Doing a reboot, i read if i use the following: nvidia-persistenced && sleep 5 && fuser -k /dev/nvidiactl it is safer if i decide to do any VM's later. So am trying that UPDATE: Current uptime is 29m and Unaminic compressing without issue....

crazytower-diagnostics-20260327-1913.zip Diagnostic attached. After three reboots all is working again WTF ???? GPU Stats show 01:00.0:RTX 4060 TI - 0000:01:00.0 when opening the settings cog NVIDIA Driver is Production Branch V595.58.03 Installed GPU(s): No devices were found GPU Driver Support: 01:00.0: VGA compatible controller [0300]: NVIDIA Corporation AD106 [GeForce RTX 4060 Ti] Detected via: lspci Chip codename: AD106 Architecture: Ada Kernel module support: both Device ID input: 10de:2803 Normalized ID: 2803 Supported candidates: 580.142, 590.48.01, 595.58.03 Recommended Driver: 590.48.01 (open-source) nvidia-smi says Unable to determine the device handle for GPU0: 0000:01:00.0: Unknown Error

I will pull a diagnostic later..Just annoying how its working fine then gone with no apparent reason,, GPU and PSU are basically new motherboard and cpu are old asus Z170pro gaming and an i7 6700k. About to have dinner then will check gpu is working as monitor is fine....oh the joy

So a quick question, does anyone just have the occasional disappearing GPU. Been running a 4060ti with no issue. I usually come home to find one of the dockers with Nvidia set up having errors. Has occurred twice so far. The first time i reconnected the monitor until i found a driver that worked. Put my dummy hdmi back in a different slot but was okay. I think i was using either 580 or 590 drivers. Recently 595 drivers came out and it auto updated, had to restart system and things seemed okay. It has just happened again. Not detecting GPU it dropped while unmanic was processing so gave a swag of errors. I have tried 590.48.01 and 595.58.03 both production and latest but same error. Any thoughts, nvdia-smi reports nothing system devices shows iommu removed. i doubt it but will test monitor next

@chodeus Thanks up and running

@chodeus I migrated to FolderView3 today - hoping to go through the process to get it added to CA. Is that why your folderview2 plugin showed an an update a few hours before its status became unavailable on the plugins page. How should one proceed, delete folderview2 the manually add folderview3 ??

@chodeus thanks my friend. have reconfigured with your fork using manual add and started again fresh. All is working as it should. When you update does this auto update or is it manual again. i see the folder view app is now set to reinstall only from the apps tab. But looks fine when going settings and click the entry..as i said new to the nuance of Unraid

@chodeus thanks for that, bit late at night here to do so will look at tomorrow. New to Unraid. so what is best practice to remove or update this plugin to the beta version. I I cant see an export function. The first page one has manual install instructions which i guess appears as a downloaded plugin when done. Copy the folder.view2.plg file to /boot/config/plugins/ folder. Copy the latest 'folder.view2-.txz' archive to /boot/config/plugins/folder.view2/ folder. In Unraid webui go to Plugins -> Install Plugin tab, click on the folder config -> plugins -> folder.view2.plg and press install button. Use the Import to import the setting you exported... Thanks in advance for the advice

So I have read through all the pages and found some mentions but no definitive answer for my question. Using V2025.04.13 Unraid V7.2.3 WEB UI link broken Hover over Container and select WEBUI result is new page with about:blank#blocked Hover over World Icon and enter result is new page with about:blank#blocked Select Folder Arrow to reveal the containers and result is fine.... Any other items outside of folderview2 are fine also

Reply, not a problem. I will report back when the dummy plug arrives

Thanks for the heads up ConnerVT. I have ordered 1 for now..For many years I have run multiple QNAP's filled with the Arr's etc. This little venture in to Unraid is an experiment and a first for me, haqving fun for the most part. I am wanting to take the load of the QNAP's and process video files with Unmanic and photo fiels with Immich to begin.