Thomss

Members
  • Posts

    91
  • Joined

  • Last visited

Converted

  • Gender
    Undisclosed

Thomss's Achievements

Apprentice

Apprentice (3/14)

0

Reputation

  1. I could add more ram, it ran 6.01 with Sabnzbd and Transmission fine. Does 6.8 require more ram than 6.01? Hopefully I can get this download issue sorted and then look at upgrading some stuff. Thank you
  2. unraid-diagnostics-20200806-2315.zipThere we go. Thanks for the help guys, I'd love to get to the bottom of this.
  3. Is there a manual way of installing community apps? - Perhaps I can just install from the flash? This one feature is sucking so much of my time and it's so frustrating.
  4. I seem to be having the same issue here, but I can't seem to change the IP address for Docker. how were you able to change the IP address?
  5. The gateway from my network settings is: 192.168.1.1 dns is: 8.8.8.8 and 8.8.4.4 Thank you
  6. Hi everyone, It's been a while since I've been on here, hope you're all doing well. Recently I updated my 6.01 system to the latest stable release. As instructed I did not included my plugins folder when copying my previous backed up flash drive to the latest release. The system started and everything seems fine apart from getting Docker to work. When I copy/paste: https://raw.githubusercontent.com/Squidly271/community.applications/master/plugins/community.applications.plg Into Install Plugin - I get the message: plugin: installing: https://raw.githubusercontent.com/Squidly271/community.applications/master/plugins/community.applications.plg plugin: downloading https://raw.githubusercontent.com/Squidly271/community.applications/master/plugins/community.applications.plg plugin: downloading: https://raw.githubusercontent.com/Squidly271/community.applications/master/plugins/community.applications.plg ... failed (Network failure) plugin: wget: https://raw.githubusercontent.com/Squidly271/community.applications/master/plugins/community.applications.plg download failure (Network failure) When I go to my network settings: IPv4 default 192.168.1.1 via eth01 IPv4 172.17.0.0/16docker01 IPv4 192.168.1.0/24eth01 I can see Docker seems to be on 172.17.0.0 which I guess should be on my default gateway. I'm struggling to change this though, when I stop the array and make any changes it does not seem to affect docker, or the option to change that part of Docker is not available. Any help in getting this fixed would be greatly appreciated. Thanks, Thomas
  7. Thanks, just went and unassigned it, started the array, stopped it again and reassigned the drive it and let it build again, that completed and now it is 50% through a parity check. I'll keep an eye on that drive in the future.
  8. Evening all, Hope I get a little heads up on how to proceed now if that's ok. I just went to grab a file from a disk I do not often get files from and noticed it was copying very slowly to my local drive, naturally I checked what was up and seen Disk 3 had red balled. I grabbed the syslog, powered down and checked all cables, all looked good - powered back up. Now I am able to assign the disk, however its status is still a red ball and I am not able to do a parity check, also there is no temp showing on the main web page as all the other disks have. What would be the recommended course of action please? New config etc, Thanks in advance! Thomas. syslog.zip
  9. Must admit, I have a Mac Mini, Acer Revo and a 1st gen aTV with CrystalHD and it's my favourite box out of them all for running XBMC on.
  10. I've noticed since moving to the plg format it crashes a lot and have came home to find unraid totally unresponsive and have had to hold the power button down.
  11. Can I ask, if I run this plugin and install Plex on my Samsung D7000 TV which end does the decoding, the PMS or the TV? Thank you.
  12. I have a little issue: On the http://unraid:8080/user_scripts page - I have two buttons showing for Transmission (Start/Stop) but neither are doing anything after a reboot. when I click start on either of the 2 icons to start Transmission I get a message showing: "The rc.unraid_transmission script does not exist, please try reinstalling the application" Despite the message on the pkg page of unmenu: Currently Installed. Will be automatically Re-Installed upon Re-Boot (Transmission) Any ideas? Thanks, Thomas.
  13. Hi, Could somebody please tell me the best way to remove my current unmenu install of Transmission before installing this one? Many thanks, Thomas.