Drider

I know Weebo's probably going to shoot this down, but I'm not totally confident about the G3's... I ordered one off of Amazon and have tested it in 3 different computers, including my currently running 5.0.4 rig. I fiddled with BiOS settings to exhaustion, and tested both SD & Micro SD ports, but no matter what all tests report back a 'Blacklisted' GUID under unRAID webGUI. I will say however, that I was able to find two new G2's on Ebay for $10.00/ea +shipping and both report an 'Unregistered' GUID. It may just be my bad luck, but I'd have to say it's not a 100% guarantee that all G3's are unique. I'm sure the same could be said for the G2's but I feel you at least have a better chance... -D

Understood, thanks. I sent this from a mobile device using tapatalk, deal with the typos/auto corrections.

That's of course if whiteatom should decline. I sent this from a mobile device using tapatalk, deal with the typos/auto corrections.

I have a buddy who lives in VA. I've been talking to him about unRAID for almost a month now. He may jump on this. If you give me two days I can talk with him and have an answer for you. I sent this from a mobile device using tapatalk, deal with the typos/auto corrections.

I was going to raise the same point of lowering the asking price when I first saw this, but felt my lack of post counts here would cause some scrutiny. I'm learning fast the world of unRAID, but I'm well experienced in the world of computer parts/builds. It's a fine system for the right asking price, though you'd have to understand those drives you paid ~200.00 each are most likely going to be the first and most costly replacement for your buyer. I understand you said you'd entertain reasonable offers, but understand a reasonable offer may be well below what you'd consider reasonable.. -D

On Sale again for $59.99 - $20.00 MIR VISA Card. -D

Drive 2 (DBGS) finished sometime early this morning. Again results look ok to me, as they look pretty much identical to drive 1, but feedback is still appreciated. preclear_rpt_DBGS: ========================================================================1.14 == invoked as: ./preclear_disk.sh -M4 -A -c3 /dev/sdf == TOSHIBADT01ACA300 X3S99DBGS == Disk /dev/sdf has been successfully precleared == with a starting sector of 1 == Ran 3 cycles == == Using :Read block size = 8388608 Bytes == Last Cycle's Pre Read Time : 6:28:52 (128 MB/s) == Last Cycle's Zeroing time : 17:11:58 (48 MB/s) == Last Cycle's Post Read Time : 12:48:26 (65 MB/s) == Last Cycle's Total Time : 30:01:32 == == Total Elapsed Time 84:51:12 == == Disk Start Temperature: 29C == == Current Disk Temperature: 30C, == ============================================================================ ** Changed attributes in files: /tmp/smart_start_sdf /tmp/smart_finish_sdf ATTRIBUTE NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS RAW_VALUE Temperature_Celsius = 200 206 0 ok 30 No SMART attributes are FAILING_NOW 0 sectors were pending re-allocation before the start of the preclear. 0 sectors were pending re-allocation after pre-read in cycle 1 of 3. 0 sectors were pending re-allocation after zero of disk in cycle 1 of 3. 0 sectors were pending re-allocation after post-read in cycle 1 of 3. 0 sectors were pending re-allocation after zero of disk in cycle 2 of 3. 0 sectors were pending re-allocation after post-read in cycle 2 of 3. 0 sectors were pending re-allocation after zero of disk in cycle 3 of 3. 0 sectors are pending re-allocation at the end of the preclear, the number of sectors pending re-allocation did not change. 0 sectors had been re-allocated before the start of the preclear. 0 sectors are re-allocated at the end of the preclear, the number of sectors re-allocated did not change. ============================================================================ preclear_start_DBGS: Disk: /dev/sdf smartctl 6.2 2013-07-26 r3841 [i686-linux-3.9.11p-unRAID] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 3.5" HDD DT01ACA... Device Model: TOSHIBA DT01ACA300 Serial Number: X3S99DBGS LU WWN Device Id: 5 000039 ff4d25220 Firmware Version: MX6OABB0 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Dec 24 18:34:07 2013 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (22222) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 371) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 100 100 054 Pre-fail Offline - 0 3 Spin_Up_Time 0x0007 131 131 024 Pre-fail Always - 438 (Average 439) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 12 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 020 Pre-fail Offline - 0 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 1 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 12 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 12 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 12 194 Temperature_Celsius 0x0002 206 206 000 Old_age Always - 29 (Min/Max 21/29) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. preclear_finish_DBGS: Disk: /dev/sdf smartctl 6.2 2013-07-26 r3841 [i686-linux-3.9.11p-unRAID] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 3.5" HDD DT01ACA... Device Model: TOSHIBA DT01ACA300 Serial Number: X3S99DBGS LU WWN Device Id: 5 000039 ff4d25220 Firmware Version: MX6OABB0 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Dec 28 07:25:19 2013 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (22222) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 371) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 100 100 054 Pre-fail Offline - 0 3 Spin_Up_Time 0x0007 131 131 024 Pre-fail Always - 438 (Average 439) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 12 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 020 Pre-fail Offline - 0 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 86 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 12 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 12 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 12 194 Temperature_Celsius 0x0002 200 200 000 Old_age Always - 30 (Min/Max 21/32) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Thanks! -D

Greetings! I purchased two 3TB drives last week, as the deal was WAY too good to pass up, ($30.00/TB). I'v been running them both through 3 cycles of preclear in which one has finished, (I'll post the (3) resulting files below), but the other is still running. I'm a bit concerned about the second drive as I'll explain below my results of drive one. preclear_rpt_SEGS: ========================================================================1.14 == invoked as: ./preclear_disk.sh -M4 -A -c3 /dev/sdg == TOSHIBADT01ACA300 X3S97SEGS == Disk /dev/sdg has been successfully precleared == with a starting sector of 1 == Ran 3 cycles == == Using :Read block size = 8388608 Bytes == Last Cycle's Pre Read Time : 6:28:20 (128 MB/s) == Last Cycle's Zeroing time : 5:37:51 (148 MB/s) == Last Cycle's Post Read Time : 12:20:30 (67 MB/s) == Last Cycle's Total Time : 17:59:25 == == Total Elapsed Time 60:29:20 == == Disk Start Temperature: 27C == == Current Disk Temperature: 28C, == ============================================================================ ** Changed attributes in files: /tmp/smart_start_sdg /tmp/smart_finish_sdg ATTRIBUTE NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS RAW_VALUE Temperature_Celsius = 214 222 0 ok 28 No SMART attributes are FAILING_NOW 0 sectors were pending re-allocation before the start of the preclear. 0 sectors were pending re-allocation after pre-read in cycle 1 of 3. 0 sectors were pending re-allocation after zero of disk in cycle 1 of 3. 0 sectors were pending re-allocation after post-read in cycle 1 of 3. 0 sectors were pending re-allocation after zero of disk in cycle 2 of 3. 0 sectors were pending re-allocation after post-read in cycle 2 of 3. 0 sectors were pending re-allocation after zero of disk in cycle 3 of 3. 0 sectors are pending re-allocation at the end of the preclear, the number of sectors pending re-allocation did not change. 0 sectors had been re-allocated before the start of the preclear. 0 sectors are re-allocated at the end of the preclear, the number of sectors re-allocated did not change. ============================================================================ preclear_start_SEGS: Disk: /dev/sdg smartctl 6.2 2013-07-26 r3841 [i686-linux-3.9.11p-unRAID] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 3.5" HDD DT01ACA... Device Model: TOSHIBA DT01ACA300 Serial Number: X3S97SEGS LU WWN Device Id: 5 000039 ff4d24bf5 Firmware Version: MX6OABB0 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Dec 24 18:34:07 2013 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (22365) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 373) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 100 100 054 Pre-fail Offline - 0 3 Spin_Up_Time 0x0007 134 134 024 Pre-fail Always - 425 (Average 427) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 12 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 020 Pre-fail Offline - 0 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 1 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 12 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 12 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 12 194 Temperature_Celsius 0x0002 222 222 000 Old_age Always - 27 (Min/Max 20/27) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. preclear_finish_SEGS Disk: /dev/sdg smartctl 6.2 2013-07-26 r3841 [i686-linux-3.9.11p-unRAID] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 3.5" HDD DT01ACA... Device Model: TOSHIBA DT01ACA300 Serial Number: X3S97SEGS LU WWN Device Id: 5 000039 ff4d24bf5 Firmware Version: MX6OABB0 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Dec 27 07:03:28 2013 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (22365) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 373) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 100 100 054 Pre-fail Offline - 0 3 Spin_Up_Time 0x0007 134 134 024 Pre-fail Always - 425 (Average 427) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 12 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 020 Pre-fail Offline - 0 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 61 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 12 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 12 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 12 194 Temperature_Celsius 0x0002 214 214 000 Old_age Always - 28 (Min/Max 20/30) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Looking at my report(card)s for this drive, am I safe to assume this drive is good for placement in the array? On that note, I really don't know what I'm looking at/for in these reports. Is there an outline of how exactly read these reports? If its already been detailed in this thread, please just say so, and I'll hunt it down, I just didn't want to go through 44 pages of postings to find nothing. Really I'd like to eventually be able to judge the condition of these drives for myself. Now, about the second drive. It's still in the 3rd cycle of preclear in step 2 of 10. Everything was fine and dandy through cycle one of preclear on both drives, and they were both pretty much neck and neck the whole way through. it was in cycle 2 I became concerned as the second drive PLUMMETED in speed on step 2, (went from ~160MB/s to ~55MB/s), all other steps have ran at what appears to be nominal speeds. It again showed the same behavior in cycle 3 as it's currently in step 2 at 77% complete while running 49.3MB/s Again, I'm new to all of this, so maybe my concern is overreaction, but expert opinion/thought/advice on this is most welcome Thanks for all your assistance, -D

Ah, wonderful news! Thanks so much, I will follow your advise and check every couple months. -D Sent from my SCH-I545 using Tapatalk

Greetings! My first post, but I've been around the forums about two months now, gathering information, and learning. (Thank God for search buttons!) I've built my first unRAID box, thanks to my father, and I'm looking to add the HDD's I was previously using to store media files, (.iso's). The drives were never in a system, but always used in a Thermaltake BlacX Duet. Anyway, I'd like to use these drives, as I don't have much else at the moment, and I will plan to upgrade them eventually, just not sure exactly when. I'm not sure what all I need to attach but for now, here's the 4 preclear.sh reports: 4BXV1: ========================================================================1.14 == invoked as: ./preclear_disk.sh -A /dev/sdg == ST31500341AS 9VS4BXV1 == Disk /dev/sdg has been successfully precleared == with a starting sector of 64 == Ran 1 cycle == == Using :Read block size = 8388608 Bytes == Last Cycle's Pre Read Time : 5:05:15 (81 MB/s) == Last Cycle's Zeroing time : 4:21:02 (95 MB/s) == Last Cycle's Post Read Time : 10:24:25 (40 MB/s) == Last Cycle's Total Time : 19:51:44 == == Total Elapsed Time 19:51:44 == == Disk Start Temperature: 30C == == Current Disk Temperature: 31C, == ============================================================================ ** Changed attributes in files: /tmp/smart_start_sdg /tmp/smart_finish_sdg ATTRIBUTE NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS RAW_VALUE Raw_Read_Error_Rate = 116 117 6 ok 103695522 Seek_Error_Rate = 62 61 30 ok 1576598 Spin_Retry_Count = 100 100 97 near_thresh 0 End-to-End_Error = 100 100 99 near_thresh 0 High_Fly_Writes = 84 91 0 ok 16 Airflow_Temperature_Cel = 69 70 45 near_thresh 31 Temperature_Celsius = 31 30 0 ok 31 Hardware_ECC_Recovered = 60 48 0 ok 103695522 No SMART attributes are FAILING_NOW 0 sectors were pending re-allocation before the start of the preclear. 0 sectors were pending re-allocation after pre-read in cycle 1 of 1. 0 sectors were pending re-allocation after zero of disk in cycle 1 of 1. 0 sectors are pending re-allocation at the end of the preclear, the number of sectors pending re-allocation did not change. 0 sectors had been re-allocated before the start of the preclear. 0 sectors are re-allocated at the end of the preclear, the number of sectors re-allocated did not change. ============================================================================ BCJ7: ========================================================================1.14 == invoked as: ./preclear_disk.sh -A /dev/sdf == ST31500341AS 9VS4BCJ7 == Disk /dev/sdf has been successfully precleared == with a starting sector of 64 == Ran 1 cycle == == Using :Read block size = 8388608 Bytes == Last Cycle's Pre Read Time : 4:41:25 (88 MB/s) == Last Cycle's Zeroing time : 4:23:44 (94 MB/s) == Last Cycle's Post Read Time : 10:34:57 (39 MB/s) == Last Cycle's Total Time : 19:41:07 == == Total Elapsed Time 19:41:07 == == Disk Start Temperature: 33C == == Current Disk Temperature: 34C, == ============================================================================ ** Changed attributes in files: /tmp/smart_start_sdf /tmp/smart_finish_sdf ATTRIBUTE NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS RAW_VALUE Seek_Error_Rate = 70 69 30 ok 10659712 Spin_Retry_Count = 100 100 97 near_thresh 22 End-to-End_Error = 100 100 99 near_thresh 0 High_Fly_Writes = 1 1 0 near_thresh 477 Airflow_Temperature_Cel = 66 67 45 In_the_past 34 Temperature_Celsius = 34 33 0 ok 34 Hardware_ECC_Recovered = 55 35 0 ok 30022470 No SMART attributes are FAILING_NOW 0 sectors were pending re-allocation before the start of the preclear. 0 sectors were pending re-allocation after pre-read in cycle 1 of 1. 0 sectors were pending re-allocation after zero of disk in cycle 1 of 1. 0 sectors are pending re-allocation at the end of the preclear, the number of sectors pending re-allocation did not change. 43 sectors had been re-allocated before the start of the preclear. 43 sectors are re-allocated at the end of the preclear, the number of sectors re-allocated did not change. ============================================================================ 07CY: ========================================================================1.14 == invoked as: ./preclear_disk.sh -A /dev/sdi == ST31000340AS 5QJ107CY == Disk /dev/sdi has been successfully precleared == with a starting sector of 64 == Ran 1 cycle == == Using :Read block size = 8388608 Bytes == Last Cycle's Pre Read Time : 3:19:23 (83 MB/s) == Last Cycle's Zeroing time : 3:16:38 (84 MB/s) == Last Cycle's Post Read Time : 7:36:59 (36 MB/s) == Last Cycle's Total Time : 14:14:01 == == Total Elapsed Time 14:14:01 == == Disk Start Temperature: 30C == == Current Disk Temperature: 31C, == ============================================================================ ** Changed attributes in files: /tmp/smart_start_sdi /tmp/smart_finish_sdi ATTRIBUTE NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS RAW_VALUE Raw_Read_Error_Rate = 118 115 6 ok 192958221 Seek_Error_Rate = 51 51 30 near_thresh 253411065852 Spin_Retry_Count = 100 100 97 near_thresh 6 End-to-End_Error = 100 100 99 near_thresh 0 Airflow_Temperature_Cel = 69 70 45 In_the_past 31 Temperature_Celsius = 31 30 0 ok 31 Hardware_ECC_Recovered = 57 40 0 ok 192958221 No SMART attributes are FAILING_NOW 0 sectors were pending re-allocation before the start of the preclear. 0 sectors were pending re-allocation after pre-read in cycle 1 of 1. 0 sectors were pending re-allocation after zero of disk in cycle 1 of 1. 0 sectors are pending re-allocation at the end of the preclear, the number of sectors pending re-allocation did not change. 2 sectors had been re-allocated before the start of the preclear. 2 sectors are re-allocated at the end of the preclear, the number of sectors re-allocated did not change. ============================================================================ 0843: ========================================================================1.14 == invoked as: ./preclear_disk.sh -A /dev/sdh == WDCWD1001FALS-00J7B1 WD-WMATV3090843 == Disk /dev/sdh has been successfully precleared == with a starting sector of 64 == Ran 1 cycle == == Using :Read block size = 8388608 Bytes == Last Cycle's Pre Read Time : 3:35:01 (77 MB/s) == Last Cycle's Zeroing time : 3:14:57 (85 MB/s) == Last Cycle's Post Read Time : 7:34:28 (36 MB/s) == Last Cycle's Total Time : 14:25:27 == == Total Elapsed Time 14:25:27 == == Disk Start Temperature: 34C == == Current Disk Temperature: 35C, == ============================================================================ ** Changed attributes in files: /tmp/smart_start_sdh /tmp/smart_finish_sdh ATTRIBUTE NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS RAW_VALUE Temperature_Celsius = 115 116 0 ok 35 No SMART attributes are FAILING_NOW 0 sectors were pending re-allocation before the start of the preclear. 0 sectors were pending re-allocation after pre-read in cycle 1 of 1. 0 sectors were pending re-allocation after zero of disk in cycle 1 of 1. 0 sectors are pending re-allocation at the end of the preclear, the number of sectors pending re-allocation did not change. 1 sector had been re-allocated before the start of the preclear. 1 sector is re-allocated at the end of the preclear, the number of sectors re-allocated did not change. ============================================================================ Thanks so much for all your help! -D