G Speed

alright perfect

Is this a plugin issue or an unraid issue? Is it even a bug, or just my ocd I'm on .18 and UD 2024.02.17, I just put in 2 drives to preclear.. Noticed the lower vs upper case - pre array start once the array is started, They both become uppercase like everything else

haha, yes I was just testing.. I tried my phone worked perfectly lol Thanks

I just set plex up to transcode, but when I do it just gives me a black screen.. Nothing happens If I revert back to direct play everything works fine Not sure what i'm doing wrong

What's funny my H310 in IT mode was not happy in my DELL server lmao, backplane got really pissed off lol

Sorry for late response, I don't get notifications honestly... does the mobo have 2 - Sff-8087 ports? If so.... just buy 2 cables "they are dirt cheap" go from backplane direct to mobo don't waste your time flashing anything Disable the "raid card" and save some power too

You can buy an HBA330 Mini, You can flash your H710 to IT Mode You can buy an H730P Mini, and set to passthrough Just want to add..... when I tried my H310 with my R530 it didn't work and gave me a backplane error

Trying to troubleshoot Spinup Issues

You sharing your Plex with anyone? are you using plex? Could be someone... deleting

I think you missed the original issue, the above is me spinning up the drives and starting.. it will do the parity scan at full speed "according to the benchmarks" for the full duration. On the other hand When unraid starts parity, when disk are spundown It won't hit over 60MB/s, 1min..40mins.. doesn't matter.. doesn't catch up.. doesn't slow down

Total size:6 TB Elapsed time:44 minutes Current position:525 GB (8.8 %) Estimated speed:193.1 MB/sec Estimated finish:7 hours, 53 minutes Sync errors corrected: 0 Everything is 100% fine when I spin up drives

First minute sure, not 16mins 26mins still same Stop parity, try again same Spin down, spin up

All perfect, did it yesterday...

This is my concern..... Parity whatever.. I can spin up then start. But what's odd is when parity is running, and I pause it.. and wait.. All drives are spun up, if I resume.. same slow speed. If I spin down, then up again full speed!

I can try sure, but I have never seen this behavior on my other unraid systems

Downgraded to 6.9.2 same issue

So I'm testing a new server.... Using Version: 6.10.0-rc5 Here is what's happening... Drives Spun Down... I click check parity, Drives spin up. I get 50-60MB/s per drive I Cancel... I spin drives down.. then I spin drives up Start parity, I get 200MB/s per drive Cancel.. Spin Down.. Click Parity... 50-60MB/s I can replicate this every time Log SHOWS nothing May 3 21:24:47 Tower2 emhttpd: read SMART /dev/sdb May 3 21:24:48 Tower2 emhttpd: spinning up /dev/sdh May 3 21:24:52 Tower2 emhttpd: read SMART /dev/sdh May 3 21:24:52 Tower2 emhttpd: read SMART /dev/sdd May 3 21:24:53 Tower2 emhttpd: spinning up /dev/sdi May 3 21:24:57 Tower2 emhttpd: read SMART /dev/sdi May 3 21:24:58 Tower2 emhttpd: read SMART /dev/sde May 3 21:24:58 Tower2 emhttpd: spinning up /dev/sdc May 3 21:25:10 Tower2 emhttpd: read SMART /dev/sdc May 3 21:25:10 Tower2 emhttpd: read SMART /dev/sdf May 3 21:25:10 Tower2 emhttpd: read SMART /dev/sdg May 3 21:25:11 Tower2 emhttpd: read SMART /dev/sdh May 3 21:25:11 Tower2 emhttpd: read SMART /dev/sdi May 3 21:25:11 Tower2 emhttpd: read SMART /dev/sdc May 3 21:25:20 Tower2 kernel: mdcmd (46): check May 3 21:25:20 Tower2 kernel: md: recovery thread: check P Q ... May 3 21:25:27 Tower2 kernel: mdcmd (47): nocheck Cancel May 3 21:25:27 Tower2 kernel: md: recovery thread: exit status: -4 May 3 21:25:38 Tower2 ntpd[1526]: kernel reports TIME_ERROR: 0x41: Clock Unsynchronized May 3 21:26:30 Tower2 emhttpd: spinning down /dev/sdh May 3 21:26:30 Tower2 emhttpd: spinning down /dev/sdg May 3 21:26:30 Tower2 emhttpd: spinning down /dev/sdd May 3 21:26:30 Tower2 emhttpd: spinning down /dev/sde May 3 21:26:30 Tower2 emhttpd: spinning down /dev/sdb May 3 21:26:30 Tower2 emhttpd: spinning down /dev/sdf May 3 21:26:30 Tower2 emhttpd: spinning down /dev/sdc May 3 21:26:30 Tower2 emhttpd: spinning down /dev/sdi It's a Dell R530, with an H730 set to HBA <- Yes it's a proper IT Mode, full disk pass to OS, Smart Etc... This is when unraid calls for a spinup for parity check I will cancel the above.. SPIN DOWN the array.. then SPIN UP.. Start parity check..

Thanks! going to try the fixes right now the kb on 45 drives got updated as well for bigsur

Hey everyone, Quick thanks to the girls and guys on discord! so I'm having some crazy issues and I have no idea how to fix them, I'm brand new to Mac wanted to try something different First thing I noticed was I can't search my unraid server, not command + space.. but just a regular folder search. I did get it working very shortly, but it caused the server to unmount and need to be reconnected every time I left finder. aka I would click on share, it would load an empty folder, then kick me back out to main... then would need to reclick to login in again. Second Issues, unraid created a folder/file "torrent"..for some reason I can't see the directory on the Mac... I can view it on windows and the webgui I went into unraid and enabled MacOs Operatbility thing under SMB, and guess what it worked!! I could see the directory....but no files in it... So I wanted to try something, so I created a new folder within.. and it gave me an error code 43 Some google searching hit me with this https://www.qnap.com/en/how-to/faq/article/sometimes-i-get-an-error-code-43-when-attempting-to-access-files-in-a-shared-folder-while-using-finder-in-macos-via-smb-what-causes-this No idea how to replicate this in unraid... Thanks in advance

I didn't even know they did youtube lol

actually it's just an i3 on one of my rigs xmrig off total used free shared buff/cache available Mem: 15884 1906 2546 738 11431 12931 Swap: 0 0 0 Xmrig on total used free shared buff/cache available Mem: 15884 4268 197 738 11418 10571 Swap: 0 0 0