lovswr

Upgraded to 6.12.6 with no issues.

Yes, it is still the same with an incognito window. I also tried using the ip address instead of my server name & still get the same behavoir.

So I spoke too soon. Just white space under Dashboard. All other tabs work. This is in Chrome and Edge. IF I stop/start the server, it will work, until I navigate away from Dashboard, but when I come back, just white screen.

Was on 6.11.4. Upgraded to 6.12 wiht no problems. Then about 24 hours later, my Dashboard just showed a white screen (I use chrome). Upgraded to 6.12.1, just now, & dashboard is back. No problems with unRAID running with either version.

Thanks, Squid!

unraid v 6.9.2. Never seen an alarm anythng like this. Fix Common Problems' suggestion seems so dire. Told me to post diagnostics and ask for help, immediately. So here I am. TAI valhalla-diagnostics-20220123-1406.zip

I'm at my wits end. I have been having trouble with my docker for 2 or 3 months. Mainly, the running dockers just stop & the error is typically the docker image is either full or corrupted. I have done some of the things posted in this very thread such as deleting the image completely & changing the size. This helps for a few days but then it will just crash again. I keep the image on my 1 TB ssd cache & I have run tests on that drive that say it is ok. I just don't know what else to do. Docker was running fine last night & now this morning it has crashed. Diagnostics attached. valhalla-diagnostics-20211128-0642.zip

Just wanted to say I just upgraded to 6.9.2 with no problems. I never had a password for root (or any of my other selves as users) but I set one (for root & one user) just before I upgraded. Whole process took about 7 minutes or so.

I upgraded to 6.9.0 by first backing up my flash & then just hitting the yellow banner that told me there was a new version of unRAID available. Then I hit 'REBOOT' at the bottom of the screen. After about 10 minutes I noticed that PLEX had not come back online. I specify a static ip address for my unRAID server & when I checked my routers LAN status page it was not there. I went to my little "server closet" & it was still running. I hit the power button one time & it shut off immediately. At first this alarmed me, but I realized that the reboot command had stalled at just before, you know rebooting the server. Hit the power button again & she booted right up.

Thanks for this quick fix. I set speedtest to run at 0300 every night. Just noticed it was not working. This is why this forum/unRAID is the best.

I have the exact same problem. I went out of town, for a funeral, last Friday & tried to access Plex remotely. It failed. Got home yesterday (Sunday) & docker says it is running, but I cannot access via desktop nor via any of the local clients in my house. I'm using the linuxserver version & I uninstalled & installed the binhex version. Now desktop access works, but I really like the linuxserver version so I uninstalled binhex & went back to limuxserver. Same problem returned. Nothing changed on my network or unRAID server as I was not even home when this problem started. Same ports are forwarded through my firewall.

Well this was really bugging me so I kept at it. I swapped the LSI controller card for the spare I have on hand. Still the same symptom. This morning, I took the case apart. Since my drive bay enclosures are for SATA drives, they have SATA power connectors. I have a modular PS & I was using MOLEX connectors with MOLEX to SATA adapters. I removed the adapters & am running SATA cables straight from the PS. Rebooted & the rebuild is running at about 172.5M/s as I type these words. I really hope that fixes my problem.

So, itimpi since you gave me direction to investigate, this is what i did: I have this Mediasonic 4-disc drive bay holding 3 discs, including the aforementioned disk1. It is vertically orientated & sits at the top of my case. Just beneath it is a 5-disc drive bay holding 4 discs that is horizontal in nature. Both are connected to a LSI 8-port controller. First I shutdown & checked/reseated all SATA connectors & power leads. Rebooted & I got rebuild speeds of mid 50M for about 15 minutes, then it tricked back down to less than a k & the log showed the same errors as before. Shutdown again & completely frogged the SATA cables; that is to say I unplugged the 4 cables from the Mediasonic drive bay & plugged those cables into the other drive bay & vise-versa. This time I got acceptable speeds for about 30 minutes, then, again, it made its way back to sub 1000 B/sec. After I thought about this some, I realized that all of my drive failures over the last 2 years or so have come from drives installed in the Mediasonic drive bay. I have a second Mediasonic bay that I am going to install to see if that is the issue. I have a Corsair 750W PS which is less than a year old & I believe it sufficient to power 7 SATA drives, one USB jump drive, & about 5 fans. However, all the drives are essentially coming from one "rail" on the PS so I will have to divvy that up better.

unRAID v 6.71 - Had a drive fail, so replaced it with a new one. The rebuild rate is 809 KB/sec or 59 days for an array consisting of 6 4TB drives & 1 parity drive. I then looked at the log & thought my Parity drive was also failing. However, after looking through the forums here, I have concluded that I have no idea what is wrong. So I have included my diagnostics. Thanks in advance.valhalla-diagnostics-20191205-2244.zip

Just wanted to say that my old APC Back-UPS 550 finally bit the dust. I had it for over 5 years & the battery has been replaced once. I just bought a new APC Back-UPS 1100 & made no changes to apc-deamon. It appears to be working just fine.

Thanks, that did the trick!

So put the array back into maintenance & run the disk check with the command above?

Whoops! I knew I was forgetting something. valhalla-diagnostics-20190913-1341.zip

My disk 1 failed about 6 or 7 weeks ago. Well I just replaced it a few days ago with a new Seagate ST4000NM0035. Pre-clear was fine & added it to my array. After a successful parity-check, all my little triangles are green. Everybody's happy, right! Well I went to save something to a share on disk 1 & now I keep getting 'Disk is write-protected'. After mucking around a bit, I decide to do a maintenance mode check of disk 1. I have included the output because I don't even know where to begin. It is a 4TB drive with 52% utilization. Thanks in advance for any solutions or input on how to fix this problem disk1-check.txt

I had a similar problem and my guide refused to update & I could no longer access my Plex server outside my house. Did as you instructed to move over to the Linuxserver version. It is now updating the guide & it also appears that remote access has been restored. Kudos & thanks!

Thanks johnnie.black. I did as you instructed & I now have over 50G of free space on my SSD cache. I will be watching closely over the next 3-5 days to see how it performs.

As requested. valhalla-diagnostics-20190704-1341.zip

Hello, I started getting this error about 4 days after I upgraded to v6.7.1. I have 4 docker containers (duckdns, openvpn-as, PlexMediaServer, & smokeping) & they all stopped & will not restart (reports Execution Error when I try to restart them). At first I thought the problem was related to the advanced server tuning that I did after watching this most excellent video by Spaceinvader One. However, after reading here that BTRFS errors tend to imply some kind of problem with the cache drive & after looking at the recent red alerts on my server all showing disk space low on my cache drive, I'm pretty sure the problem is with my cache drive. A simple restart of my server will get the dockers running again, but if anybody has any ideas on how to fix this problem I would certainly appreciate it. The full error reads like the below & just kept repeating

I have the same issue. No sound at all. I also would like to commend the OP for this excellent tutorial. Really easy to follow AND he explains things. Having said that it was not obvious (at least not to me) that if you try to get Windows 10 from Microsoft while using a Windows machine, that download page will try to force you to use that horrible tool. The trick is to change the User Agent in the browser session of the download page. For example if one is using Chrome, here is how to do it. Last thing. Did anyone actually manage to buy a working Windows Pro license from that website? That price seems too good to be true.

Yep, I just found it about 1 minute before your response. Parity is rebuilding now without that empty 4TB drive. After rebuild I will just swap out the mostly full 3TB for the empty 4tB. Thank you for your excellent & speedy assistance.