jsn0327

Members
  • Content Count

    40
  • Joined

  • Last visited

Community Reputation

0 Neutral

About jsn0327

  • Rank
    Newbie

Converted

  • Gender
    Undisclosed

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Where can I find release notes on pre-releases? When I install the plugin on the referenced page for pre-releases, the next release (6.4-rc3) shows up in my plugins list with "REBOOT REQUIRED". I don't see any release notes. Thanks.
  2. LoL! Thanks, I'll try it out.
  3. Thanks for the clarification. When will 6.4 be released? I just updated to 6.3.5 so will we have to wait 5 more update cycles for this feature, or will the next update go to 6.4?
  4. I noticed that VLAN support was added to unRAID. I setup a few VLANs in Settings/Network, but I can not figure out how to assign a Docker (such as Plex) to a specific VLAN. Would someone please point me to some documentation that explains how to use VLANs once you have them added? Thanks! -Jason
  5. I work in the field of Cyber Security and you don't have to open your network up to the world for there to be risks of intrusion through vulnerabilities of many other avenues. As I mentioned previously, I use unraid as my primary NAS and store a lot of important documents on it. In the event that my network is compromised, I'd rather not make it even easier for the attacker by sending my login credentials to him in the clear. I find it hard to believe that with all of the cyber crime going on throughout the world, simple SSL security is an afterthought on a product that we pay for. I could kin
  6. How is that an excuse not to implement security? Even if that is the case, it has evolved a lot with the implementation of VM's and Docker. It's sad that every Web interface that I run on top of unraid is https enabled, yet unraid doesn't support it.
  7. That's a ridiculous approach if u ask me. I mean, it's only holding ALL of our confidential documents. Guess that's why they haven't implemented VLAN's either... Thanks for confirming what I hoped wasn't the case.
  8. I figured that was the case. Why isn't it supported?
  9. Hi everyone. Does unRAID support HTTPS (Port 443)? I can not find anywhere within the settings page to enable it. I've searched the forum and haven't found anything. Thanks.
  10. Thanks a lot for the recommendation. I may end up going that route. Unfortunately, in order to scan wirelessly, the scan has to be initiated by the desktop. I was hoping to have the ability to quickly scan documents by pressing the scan button on the front of the scanner and sorting the files later without having to turn my desktop on (since my VM is always running), but that may not be possible without PCI pass-through, or leaving the scanner on all of the time.
  11. You can set the scanner to not sleep, but I won't use the scanner on a daily basis, so I'd rather let it sleep and extend the life of it. I received my USB 3.0 PCIe card and installed it. After modifying the XML of my Windows 8.1 VM and trying to start it, I receive an error stating that my host does not support PCI pass-through. After researching the processor in my server (AND Turion II) I discovered that my processor does support AMD-V for virtualization, but not AMD-Vi, which is needed for PCI pass-through. Is there a way to make the USB port hot pluggable without passing through t
  12. Thanks a lot jonp and billington.mark! jonp your method worked right away! Now my scanner works perfectly with my Windows 8.1 VM with one little exception.... The SnapScan iX500 goes into a sleep mode after 4 hours of inactivity; or if you close the top cover. When it goes into sleep mode, the USB disconnects and does not reconnect until i stop and restart the VM. I am guessing that the only way to disconnect and reconnect a USB device while the VM is running is to pass through the whole controller? jonp, is there any way to do it with your method? Thanks again for both of your help. I
  13. Thanks for the reply! I'm actually trying to do that now, but I am getting an error when I try to start my VM. I posted the error at the link below. Any suggestions? Thanks. https://lime-technology.com/forum/index.php?topic=36768.new#new
  14. I followed this guide to passthrough the USB controller that my FUJITSU SnapScan document scanner is connected to, but I am getting an error when I try to start my Windows 8.1 VM about the following line; which the guide says is required. <qemu:arg value='ioh3420,bus=pcie.0,addr=1c.0,multifunction=on,port=1,chassis=1,id=root.1'/> I don't understand why this line is required as it is written? What if my server does not have the device ioh3420 on bus pice.0 with address 1c.0? Please see the attached screenshots. My XML for the VM is below. I'm running unRAID 6.1.3. Thanks!