arobinson888

Hello, I am running into an issue where i need to replace the USB key for my unraid installation. The issue though is that I do not have access to a Windows or Mac machine to follow the creation instructions on the website. I did try building a Windows VM in virtual box 5.1, but could not get it to see the USB key. Does anyone know how to create the USB installation from a Linux machine (specifically Ubuntu)? Thank you

I'm using the memory usage meter on the dashboard.

Hey, For the last few weeks I seem to be suffering from a memory leak on my unraid server. this had originally started with 6.1.6, but has persisted with an upgrade to 6.1.7. I originally noticed the issue when I had enabled networking bonding. With bonding turned on my network usage automatically climed approximately 30% with no other changes on the system. With network bonding turned off, my memory consumption continues to climb from when I power on the server to the point where it shuts down running vm's due to a alack of free memory. I have attached a copy of my diagnostics file for trouble shooting. Any ideas as to what I may have configured incorrectly? Thanks Andrew galactica-diagnostics-20160122-2043.zip

Hey, Does anyone know why when I enable 802.3ad network bonding, my ram consumption goes up by nearly 30%? With it turned off, my system in use uses about 65% of the installed ram, with 802.3ad bonding turned on (and with no other changes made) ram consumption goes up to 95% use? I am using unraid 6.1.6. Both NICS are intel 1GB, managed switch is a netgear gs-110TP. the bond reports as being up and running, the only issue is that it uses so much ram, it causes kvm to turn off my running vm's Thanks

Hello, has anyone got any experience with configuring unraid 6.1.3 as a PDC? I am wanting to use logon scripts for my network so that I can mount specific shares automatically. Thanks

Hello, Is anyone using the CUPS plugin from gfjardim's Docker Repository? The HP printer I am attempting to use is a LaserJet professional M1212nf. Cups is telling me that I need a proprietary plugin. I am assuming that this is HPLIP based upon my research. My question though is, is this installed by default in the docker image? and if not how do I go about installing it? The current issue I am running into that is causing this line of thinking is that when I am attempting to print a test page from cups I get the following error message "Failed to connect to system bus". Thanks

Hey Guys, jonp asked me to pass along this information to you this plugin. http://lime-technology.com/forum/index.php?topic=42919.0 This thread was about some issues I was having with this plugin and its preventing my VM's from working. I was using the current version of the VM up till the point I uninstalled it. The basic gist of the issue was that with this plugin installed after between 12 - 20 hours I would get the following error After a lot of trouble shooting and back and forth, we finally narrowed it down to the plug in. This issue was occurring with the 6.1.2 version of Unraid. If you need anymore details about it, just give me a shout. Andrew

I uninstalled the unassigned devices plugin as it wasn't being used at the moment. Since uninstalling it, my system has run for 24 hours without issue, not in safe mode, but in regular. I have even been able to stop and restart VM's, which I wasn't able to before. I believe this issue may be resolved now, however I'm curious why this plugin would cause these issues. The version installed was the most current one available, and I had not had any issues with it, until I had to remove the one drive that I was using it for. I'm not sure why physically removing that drive though would cause this issue. I'm just curious about the correlation at this point. Thank you for all the help jonp!

Attached are my diagnostics. Motherboard Tyan S5512 Proc Intel Xeon 1230 Ram 8GB Kingston ECC 1 x 4TB Seagate HDD (Parity) 2 x 3GB HDD (One Seagate, 1 Western Digital) (Data) 1 x Kingston 16GB USB3 Flash drive 1 x Asus GT730 graphics card (for Openelec VM) The mobo, proc, Ram, and hard drives have been in use for over a year and a half now without any observed hardware issues. galactica-diagnostics-20150919-1700.zip

No dice. All VM's died within 6 hours of applying the above fix.

Before running this process everything ran for 16 hours without issue. I've rebuilt all of my VM's according to your instructions. I'll give it 24 hours before saying it is working properly or not though.

OK, you should be able to view the file from my one drive account. The file can be accessed from https://boohaha-my.sharepoint.com/personal/andrew_boohahaonline_com/_layouts/15/guestaccess.aspx?guestaccesstoken=2gVtdnPE2kGaHSpa6qZX4hsmnAFO%2fHRKFnU%2bfj9uyTI%3d&docid=00d328f41cd914ee8b394bb423ceaed5f

Changed out my USB key for another one that I had, it is even newer than the one that was replaced. Am still having the same issue. It seems to take somewhere between 12 and 20 hours before this issue arises. Rebooting temporarily does fix it.

I think I've had it sitting on a shelf now for about 1-2 years, where it's hardly ever been touched. I've only been really using it for the last month or two though. How do I go about replacing my existing USB stick with a new one, without losing any settings? Is it just a matter of copying one stick to another?

How do I stop my IPMI keyboard and mouse from being passed through to be used with VM's? From what I can see it is because of this pass through that prevents me from using them both were they are meant to be used. Currently when I log into my server's IPMI java control, I have neither keyboard or mouse control. This is what is listed when I check the system devices Unraid 6 is seeing. Bus 001 Device 005: ID 046b:ff10 American Megatrends, Inc. Virtual Keyboard and Mouse Bus 001 Device 004: ID 046b:ff01 American Megatrends, Inc.