Dave-Kay
-
Posts
79 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Store
Gallery
Bug Reports
Documentation
Landing
Posts posted by Dave-Kay
-
-
16 minutes ago, trurl said:
Without rebooting from that condition, attach diagnostics to your NEXT post in this thread.
Thx for your help. Here's my diagnosticresult
-
-
23 hours ago, Gunny said:
https://blog.chaospixel.com/linux/2016/09/Fan-control-on-Asrock-C2750D4I-C2550D4I-board.html
seems to have ipmi-raw commands for your motherboard.
based on that, this json file might work for you:
{ "ASRock": { "raw": "00 3a 01", "auto": "00 00 00 00 00 00 00 00", "full": "64 64 64 64 64 64 00 00", "fans": { "CPU_FAN1": "01", "CPU_FAN2": "01", "REAR_FAN1": "01", "REAR_FAN2": "01", "FRNT_FAN1": "01", "FRNT_FAN2": "01", "FAN_POS7": "01", "FAN_POS8": "01" } } }
Just in case that blog article ever gets removed, here is the pertinent information:
ipmitool raw 0x3a 0x01 AA BB CC DD EE FF 0x00 0x00
Each block must be replaced with the requested fan control value.
AA : CPU_FAN1
BB : CPU_FAN2
CC : REAR_FAN1
DD : REAR_FAN2
EE : FRNT_FAN1
FF : FRNT_FAN2
The control value is one of the following:
0x00 Smart fan (Duty cycle setting from BIOS)
0x04 min. RPM value
…. increase RPM value
0x64 max. RPM value
That, actually mnakes me wonder. I changed from 2550DI4 to the actual board. Also, on the 2550 the script to get the values worked wel..
Will try it later on, anyway. -
14 hours ago, SimonF said:
does ipmi-raw 00 3a d7 and ipmi-raw 00 3a da provide any output?
Quoteipmi-raw 00 3a d7
rcvd: D7 C1Quoteipmi-raw 00 3a da
rcvd: DA C1 -
On 12/2/2023 at 2:12 PM, SimonF said:
Have you run the ipmi2json command to create the file for ASRock systems and can you supply the file.
root@unraid:/boot/packages# ipmi2json --help
Check ASRock IPMI fan locations using ipmi-raw command and
create a json array for ipmifan script.Usage: ipmi2json [options]
-f, --force force start
--debug turn on debugging
--help display this help and exit
--version output version information and exitHello,
thanks for your support.
The ipmi raw command leads to exactly nothing. It gives no return whatsoever.
ipmi2json is attached:
kind regards
Kai
Quoteipmi2json
Checking IPMI fan Locations...
Location 0-1: none
Location 0-2: none
Location 0-3: none
Location 0-4: none
Location 0-5: none
Location 0-6: none
Location 0-7: none
Location 0-8: none
Saving board configuration...
-
3 hours ago, SimonF said:
I have released 2023.12.02, If you have tested the Dev release you may need to update the Fans section as I have changed name to FAN123456 for All for Dell systems
- Add FAN Control support for Dell systems.
- Add Supermicro X12 options. Thanks to C4Wiz for PR.
- Add ASRock EP2C612WS Support thanks to WillGunn for PR.
- Set shift class in table sorter thanks to kcpants for PR.
- Refactor code to allow easier models+boards to be added.
Nice,
but is there a possibility to add ASRockRack W680D4U-2L2T/G5
it works fine with the sensors but won't find the fans.
Can i deliver anything to make it easier for you?
Kind regards
Kai -
that was really fast, thank you!
i was able to switch to the new device. i assume assigning a second later on is no problem at all.- 1
-
I bought new hardware and now i'm trying to optimize the system to my needs
there was a pool of two 240GB SSDs which were the cache. What is the recomended way to switch to a new pool of 2 1TB SSDs, or maybe to a single 1TB drive (atm i am not sure, if i want a pool) -
Holy cow..... i always thought i was using uefi on the old system...
Thank you! -
Dear all,
my serverboard died a few days ago, so i bought a new one. The new one is a Asrock W680D4U-2L2T/G5.
But thios won't boot any Unraid-USB-Stick. it doesn't matter if i take the one, which was attached to the dead board, or a completley new one, or even the one, from my backup-Unraid.
The board doesn't talk to me about it, it won't say, that this is no boot device or somethiong like that, it just gets back to bios or boot menue, depending on how i tried to boot from the stick.
a Truenas stick bootet immediately, as did an batocera stick.
Can anyone point me in the right direction? -
Label: none uuid: b843e3cb-a537-434b-9212-747a404af834 Total devices 2 FS bytes used 4.12GiB devid 1 size 223.57GiB used 17.03GiB path /dev/sdb1 devid 2 size 223.57GiB used 17.03GiB path /dev/sdj1
- 1
-
Sorry, i couldn't find an answer in the faq or somewhere else.
If there is a howto or something similar, please close/delete this and point me to it.
There have been some issues in the recent past, so i decided to switch hardware. (just Motherboard CPU and RAM)
From my understanding there should be no trouble at all, simply changing hardware, building the array exactly as it was and telling the config the parity drive allready is valid. or maybe, the drives will be set correctly already? (but i doubt that as the sata controllers and Ports will be changed)
Am i wrong on this? The license is, as i understood it, tied to the USB-Stick and nothing else!?
as bonus questions, i'd like to change parity drive as well and switch to SSD , but i am not fixated on using it as a parity drive, most likely all drives will switch to ssd sooner or later anyway, what are the up- and downsides doing it to the parity first? -
While the cache isn't encrypted, could it be possible the encryption of the array has a play in it?
-
wow! Thank you!
I was suspecting the cache-Drives, but i didn't know how to prove it.
Where did you find the problem.
And well, THANK YOU!- 1
-
yes it does.
i allredy tried several reboots
here -
Dear all,
i tried to remove a HDD with this
https://wiki.unraid.net/Shrink_array
it all went well, until i stopped the array. it got stuck in unmounting drive 7 which i removed with this method, saying unmount drive 7, drive not mounted.
i read in the forum, the only way out of this loop seems to be rebotting the server.
After the reboot i followed the manual again and made a new config and started the array.
it got stucked in mounting the disks, as it said and told me this
---------------------------------------
May 1 17:57:16 UNRAID emhttpd: shcmd (205): rmdir /mnt/disk1
May 1 17:57:16 UNRAID emhttpd: mounting /mnt/cache
May 1 17:57:16 UNRAID emhttpd: shcmd (206): mkdir -p /mnt/cache
May 1 17:57:16 UNRAID emhttpd: /sbin/btrfs filesystem show /dev/sdc1 2>&1
May 1 17:57:16 UNRAID emhttpd: Label: none uuid: b843e3cb-a537-434b-9212-747a404af834
May 1 17:57:16 UNRAID emhttpd: Total devices 2 FS bytes used 4.10GiB
May 1 17:57:16 UNRAID emhttpd: devid 1 size 223.57GiB used 17.03GiB path /dev/sdc1
May 1 17:57:16 UNRAID emhttpd: devid 2 size 223.57GiB used 17.03GiB path /dev/sdk1
May 1 17:57:16 UNRAID kernel: emhttpd[6330]: segfault at 10f ip 0000151709d96236 sp 00001517092800c8 error 4 in libc-2.37.so[151709d0a000+169000] likely on CPU 3 (core 3, socket 0)
May 1 17:57:16 UNRAID kernel: Code: 00 00 66 90 66 0f ef c0 66 0f ef c9 66 0f ef d2 66 0f ef db 48 89 f8 48 89 f9 48 81 e1 ff 0f 00 00 48 81 f9 cf 0f 00 00 77 6a <f3> 0f 6f 20 66 0f 74 e0 66 0f d7 d4 85 d2 74 04 0f bc c2 c3 48 83
---------------------------------------
can anyone tell me, what to try?
-
Maybe, i got this all wrong, but i was wondering about a line in netstat, while searching for something completely different.
Quotetcp6 0 0 UNRAID.fritz.box:50408 119.142.196.35.bc.:http ESTABLISHED
and just out of curiosity i disabled IPV6, to reactivate it afterwards. But as i did so, netstat still began showing a lot of tcp V6 connections, Here are a few
Quotetcp6 0 0 [::]:microsoft-ds [::]:* LISTEN
tcp6 0 0 UNRAID.fritz.box:34876 GoogleTV.fritz.box:9080 TIME_WAIT
tcp6 0 0 UNRAID.fritz.box:35234 GoogleTV.fritz.box:9080 TIME_WAIT
tcp6 0 0 UNRAID.fritz.box:40370 sdp55-41e09a.frit:45043 ESTABLISHEDAnd as i said before, maybe i got it all wrong, but shouldn't Unraid stop listening on IPV6 and stop establishing IPV6-connections, when IPV6 is disabled?
Bonus Question, what is going in the first quoted line?
OS is Unraid 6.11.0-rc4 -
1 hour ago, Dave-Kay said:
Seems there is no support for TMM over here?
i got two problems, the first is the same that @kowabunga_dude and @sdballer are sharing.
I'm pretty shure ist is the update to V4.
Yo can fix this be deleting the tmm folder in appdata, but then you have to start new, but TMM3 will run again.
the second one, to even use v3, i seem to get no chance to set my folders in the software the container simply shows nothing at /mnt/ so i can't even get started. anyone had that and solved it?ok, nevermind, got it.
Update to V4 still won't work. -
Seems there is no support for TMM over here?
i got two problems, the first is the same that @kowabunga_dude and @sdballer are sharing.
I'm pretty shure ist is the update to V4.
Yo can fix this be deleting the tmm folder in appdata, but then you have to start new, but TMM3 will run again.
the second one, to even use v3, i seem to get no chance to set my folders in the software the container simply shows nothing at /mnt/ so i can't even get started. anyone had that and solved it? -
-
1 hour ago, knex666 said:
use that openhab/openhab:2.5.11-debian or openhab:latest
dont forget to backup before you update
I am waiting for 3.x it should be released soon
sorry, i don't get that.
is there a manual to do it, like you intend it to be done?
the "openhabian-way" doesn't work
the runtime update says i am already on 2.5.0 even if i tell him to update to 2.5.11
and with apt i am getting nowhere -
So, how is it possible to update it to 2.5.x?
-
Just a small update. The friend was told to send the board in, after it failed on luks under debian....
-
12 minutes ago, jbartlett said:
You've got three SATA controllers on there with red, white, and black ports - have you tried changing which one the encrypted drive is connected to? You'll need a mini-SAS cable for the black ones.
Do you have a SATA PCIe card? That would eliminate the onboard controllers as an issue.
ok, thanks...and fuck, this is a really good idea, while i tested other Ports (of course) i left my controller in the closet
The mini-SAS cable is in the package btw.
Unraid OS version 6.12.8 available
in Announcements
Posted
OK, thank you, that was it. Segmented my network recently and did not switch of that for the new IP.