Sparkum

Haha, so far (minus this if this is mobo related) I'm a fan of it. Maybe I'll start paying more attantion to which drives. See if its a "always drive 3 5 6 9 kinda thing" I have a LSI and mobo connections and the 8 or so times I rebooted yesterday I saw the LSI cards on the spash screen come up for 100% everytime. So I'll def start pen and papering this and ya, maybe its the mobo and I just need a second LSI card. That would be the best $100 I've ever spent because I cringe when I have to do a reboot, and I literally set aside hours to do it. I was up until almost 2 am last night and had to be up for 6:30 because I needed to get it online before work.

Definitely use adblocker on Firefox (browser of choice) I typically try to remember to reboot with IE though (as I have a much higher success rate with it) Could any of this be due to my USB? I definitely say my USB might not be the best. Just a Lexar I had lying around, it worked so I continued on with it. But if not then I wont worry about it.

Ya I see that about the logs now. Next time it happens I'll start grabbing logs (If there are of any help) Typically its just this panic trying to get it back up. Here's my question though, and I fully get what you are saying. So this has been happening for...4 months now roughly so I've done alot of googling since then. I read a post that suggested rebooting with IE. Now when I do this, I have a much greater change of everything coming back up. Just a dumb coincidence perhaps? Additionally I've used the ControlR app to reboot the server (just once) and that worked flawlessly, So I seem to get much different results depending on what I use.

..... yep no got that.. I'm asking questions, making comments, initiating 2 way conversation. Not sure how its being taken but apparently not how its meant. My last comment was stating that I didn't provide nor do I apparently have any logs covering the time frame asked for, if that wasn't clear. My previous comment was me being surprised that Trurl said it was a hardware fault since I could see the hard drives pre unraid.... So ya, apparently this isnt going anywhere and I shouldn't bother asking for help. .... with respect.

Hmm the log doesnt even cover the timeframe of the reboots, if I'm not mistaken.

Really? Even though every single harddrive is still connected and visible, I'll see them all populated under unassigned, I can see them when I drop down in the harddrive list. They are completely visible during boot, in BIOS etc, Just placed incorrectly in GUI

Attached Diagnostics. Sorry not sure how it works, I assume it just clumps is all together, esentially every reboot yesterday was a fail until the last one. And when the computer reboots I do see every single harddrive, they are just sitting in unassigned. Um.... I can definitely get more specific after work. ASRock mobo, I5, LSI flashed card, 16GB ram, 500W power supply, 11 harddrives, another 2 parity, and 2 cache drives, Mainly all 2TB, I think 3 1.5TB then 240GB Kingstons's for cache Then a 4GB Lexar flash drive. tower-diagnostics-20170209-1139.zip

Currently 6.2.4 I TRIED to upgrade last night, but I couldnt get GUI even once, so I downgraded back.

Really hoping someone can tell me what to do, Everytime, since day one that I want to reboot my unraid server it turns into an hour+ job on rebooting, having unassigned disks, rebooting etc until they are all back up. For example I went to upgade unraid last night, took me 90 minutes and the update actually failed, had to roll back. I would say I rebooted 15+ times Its definately slowly making me hate unraid when a simple reboot is actually 5+ reboots and typically having to write "shutdown -r now" into terminal atleast once. Please! Let me know what yo need from me or want me to do and I will do it! thanks

Thanks!

Ok done and done awesome thanks. Last question though, is there anyway to hide it in the Dashboard?

When I log into webgui the log shows Server started listening on :2378 But nothing else and nothing on the app.

Just installed, not sure if I'm missing something, I have shares and files set to hidden and yet I see them all. Thanks

Thanks for the reply. I've attached a screenshot oh what my logs show, this just again and again.

I actually came here to ask the very same question. Bought the app roughly 2 weeks ago, installed the plugin 10 minutes later, nothing has ever shown up under logs.

*ADDED LOGS* UNRAID_AFTER_REBOOT_SYSLOG.zip

Hey. So EVERYTIME I turn off my windows 10 VM everything goes to poop, we're talking 3 minutes to go from page to page in the gui, I am (sometimes) unable to even shutdown dockers. Today for example, I (stupidly) shutdown my Windows 10 VM first (was going to stop array, add in remove and re-add 2nd parity disk as it was kicked out, a 5minute job) so shutdown Windows 10 and then started to shut down my dockers. Every single one said "execution failed" so I figured maybe I was stop the array and it would force the dockers offline. So I click stop, then I lose complete access to the GUI, Give it about 20 minutes, then I force reboot the server. Server comes up, bunch of drives are unassigned, I reboot, some drives come back, reboot again and then they are all back up. So my 5 minute job took easily over an hour. Any tips or trick to avoid this?

Boo, Thanks for letting me know.

Just curious, never hurts to ask right.

But will the drive/vm still function. Yesterday I had to destroy my image (and the only conclusion I can reach) was the drive hit capacity, then the VM would survive for about 30 seconds then die. The second I removed the drive it would run for hours.

I am currently using UD to add a second drive to my windows 10 VM However; the drive (showing in unraid) is only increasing, not decreasing. So for example when the drive (in unraid) shows full (even though in the windows 10 is only half full) my VM just constantly crashes. How to I make the .img shrink and grow with the disk? Thanks

You'll see the difference in the screen shot. This is newly discovered so there isnt a "huge" difference, there will be a larger one in an hour as more uploads. I already had to destroy my previous UD before I came to this conclusion. The VM would last for 30-60 seconds and then just crash.

Its a disk image

Hey guys. So I have a windows 10 VM, OS is on cache drive 2nd drive is an unassigned disk, On it I run a program called stablebit clouddrive, it allows you to mount cloud providers and keep X cached. So normally I would transfer files over, it would upload the files, and keep XGB caches. all is good However, in my VM my unassigned disk NEVER decreases in size. For example I copy 200GB over, with clouddrive set to cache 50GB Net result I upload all data and cache 50GB However; unassigned shows I have 200GB What this is doing is tricking the VM into thinking the drive is maxed and crashing my VM Any resolution to this? The drive is formatted as XFS Thanks

Below is my VM log, I was hoping someone could shed some light on this, the VM stays alive for about 5 minutes then dies. 2016-11-08 05:31:24.298+0000: starting up libvirt version: 1.3.1, qemu version: 2.5.1, hostname: Tower LC_ALL=C PATH=/bin:/sbin:/usr/bin:/usr/sbin HOME=/ QEMU_AUDIO_DRV=none /usr/local/sbin/qemu -name 'Windows 10' -S -machine pc-i440fx-2.5,accel=kvm,usb=off,mem-merge=off -cpu host -drive file=/usr/share/qemu/ovmf-x64/OVMF_CODE-pure-efi.fd,if=pflash,format=raw,unit=0,readonly=on -drive file=/etc/libvirt/qemu/nvram/8f80cb25-5bfc-8fd3-efad-63389a34ee94_VARS-pure-efi.fd,if=pflash,format=raw,unit=1 -m 6144 -realtime mlock=off -smp 2,sockets=1,cores=2,threads=1 -uuid 8f80cb25-5bfc-8fd3-efad-63389a34ee94 -no-user-config -nodefaults -chardev 'socket,id=charmonitor,path=/var/lib/libvirt/qemu/domain-Windows 10/monitor.sock,server,nowait' -mon chardev=charmonitor,id=monitor,mode=control -rtc base=localtime,driftfix=slew -global kvm-pit.lost_tick_policy=discard -no-hpet -no-shutdown -boot strict=on -device ich9-usb-ehci1,id=usb,bus=pci.0,addr=0x7.0x7 -device ich9-usb-uhci1,masterbus=usb.0,firstport=0,bus=pci.0,multifunction=on,addr=0x7 -device ich9-usb-uhci2,masterbus=usb.0,firstport:3b,bus=pci.0,addr=0x3 -chardev pty,id=charserial0 -device isa-serial,chardev=charserial0,id=serial0 -chardev 'socket,id=charchannel0,path=/var/lib/libvirt/qemu/channel/target/domain-Windows 10/org.qemu.guest_agent.0,server,nowait' -device virtserialport,bus=virtio-serial0.0,nr=1,chardev=charchannel0,id=channel0,name=org.qemu.guest_agent.0 -device usb-tablet,id=input0 -vnc 0.0.0.0:0,websocket=5700 -k en-us -device qxl-vga,id=video0,ram_size=67108864,vram_size=67108864,vgamem_mb=16,bus=pci.0,addr=0x2 -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x8 -msg timestamp=on Domain id=8 is tainted: high-privileges Domain id=8 is tainted: host-cpu char device redirected to /dev/pts/0 (label charserial0) ehci warning: guest updated active QH ehci warning: guest updated active QH