-
Posts
308 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Store
Gallery
Bug Reports
Documentation
Landing
Report Comments posted by PSYCHOPATHiO
-
-
@limetech I didn't want to open a new thread for this as its tiny issue, when trying to change the description of my server with the new update I cant use "&" the "&" and anything I type after will disappear.
-
aha I had a temp win10 vm i dont use much, but once started all gone... thanks for the tip.
Once I shutdown the extra VM they all came back.
-
15 hours ago, bluepr0 said:
Just reporting the same bug, all VMs were working fine - VMs running are (FreeBSD & 2xWS2016) but once I started a win 10 VM all the VMs disappeared from the list but they are still accessible.
I have sufficient memory to run them all.
-
11 hours ago, ximian said:
The only way to get it back is to redo the original setup.
Unraid 6.7.0 rc7
I did join the active directory a couple of times & when I removed my server from active directory back to workgroup everything goes back to normal.
-
I just join one of my servers to Active Directory & the interface shrunk similarly lol, I will try leaving the and see if it changes.
EDIT: Yup, leaving the AD returns it to normal.
-
2 hours ago, bonienl said:
Do you still have your original network configuration?
What is your network setup?
1st pfSense box with physical LAN "10.0.0.0/24 and 2 VLANs "10.0.1.0/24" "172.16.1.0/24"
2nd pfSense box with 1 VPNLAN "10.0.5.0/24"
L2 Switch with 2 connected pfSense boxes and 3 VLANS in total.
Server 1 has an intel i350 Quad GBe (Balance xor) "LAN" 10.0.0.3 & a built in 1GBe "SLAN" 10.0.1.3
Server 2 has 2 built in NICs "LAN 10.0.0.4 & "SLAN" 10.0.1.4
The issue mainly was a mis-configured VPNLAN port that was able to get into the routing table 10.0.5.1 via br0
-
5 hours ago, Higgins12 said:
I'm having the exact same issue. After updating to RC6 the Server is unable to communicate with the outer world. Reverted back to RC5 all good again.
I had the same issue on both servers, then i downgraded back to RC5. Eventually I upgraded both servers again to RC6 but I deleted the /boot/config/network.cfg file and rebooted the servers & after that all was working fine.
There was a long list of troubleshooting including reseting my switch & fine tuning my pfsnese.
-
On 2/18/2019 at 4:04 PM, John_M said:
This issue is believed to be fixed in this rc (see Tom's first sentence at the top of the page and confirmation from other users). Maybe you have something else amiss that your diagnostics would show.
I confirm the issue has been resolved in RC4, thanks for the tip.
-
I noticed in all 6.7 RC1, RC2, & RC4 didn't try RC3, on both my servers the transfer rates are extremely slow around 15MB/s both servers have encrypted Arrays.
both servers are running multiple intel cards to a single managed switch (Vlans) & managed by a pfsense with a quad port intel i350 card.
I had to revert to 6.6.6
-
So, I have decided to Encrypt my array in this release but to my surprise while trying to move data from HDD to another the speeds wont surpass 15-16MB/s I tried moving files internally via "Krusader", then tried a VM with "FreeSync", then tried on my PC with "FreeSync", then resorted to "Unbalance".
Non of the above options worked faster & I noticed the speed will fluctuate between 90MB/s to Flat 0MB/s & the system will be unresponsive for a couple of seconds befoor heading up slowly back to 90 (the unraid MAIN tab reads a stable 15-16MB/s).
When I restored 6.6.6 back the copying with all the above was very fast, so I re-updated to make sure it is an issue with the new update & the copying was broke again.
I re-downgraded back to 6.6.6 & probably will stick to it till I'm done copying.
EDIT: Transfer to an unencrypted drive are at normal drive read/write speeds on 6.7RC1, the issue is only transferring to encrypted from an unencrypted.
-
updated & all is great, I love the new Dashboard.
Great work guys.
-
I got the "Annoyance" on both of my servers
I saw it after I read this thread, good catch.
-
does it take you to a blank page? I was having this but ended up wiping the new server and reverting back to 6.5
6.10.3 Web interface unavailable when MTU set to 9000
in Stable Releases
Posted · Edited by PSYCHOPATHiO
did u set your network card mtu, also if you have a switch you need to enable mtu as well.
Also there is an issue with setting it to 9000 my dockers become unaccessable via reverse proxy
in the end i revered back to default.