RevelRob

Members
  • Posts

    58
  • Joined

  • Last visited

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

RevelRob's Achievements

Rookie

Rookie (2/14)

0

Reputation

  1. Thanks for the quick reply! Ah, that's unfortunate. I'm going to try to reseat them all to see if that helps. I also have more RAM than I need for this machine so I could remove any that have failed. Also, the CPU utilization is screaming at 100% even though VMs and Docker is disabled for now.
  2. Hi, I posted this Saturday and thought all was good, but I've been experiencing additional issues that are odd: I am in the process of preclearing a new replacement disk for the one that is failing. I've turned VMs and Docker off so that there are no additional resources being used elsewhere and to not stress out the parity drive that would e emulating the disabled disk. The problem is, after a period of time, the server becomes unresponsive with no gui loading nor am I ale to SSH in. Even sending an orderly shutdown via IPMI fails. So I have to power cycle via IPMI. It also runs extremely slowly now even after a reboot. I was on an older version (6.12.6) and updated to 6.12.8 to see if that was the issue. I ran a smart test on the new drive to see if it was the issue but it came back no errors. Can anyone tell me idf they see something awry from the diagnostics file I pulled just now after a restart and pre-clear start? It also took the diagnostics almost 20 minutes to generate. Thanks! tower-diagnostics-20240311-1035.zip
  3. Haha. Nice. Too bad I have half a dozen of these to do this with now. Thanks!
  4. Hi all. I have a disabled disk and am wondering if it looks like it is going bad or if something else is happening here. I already purchased a new drive that is pre-clearing in case it is bad but want to know for sure to avoid throwing it out. Unraid version 6.12.6 Thanks! tower-diagnostics-20240309-1403.zip
  5. Thanks, it had already been replaced but I figured I’d see what the preclear plug-in said about it. She gone.
  6. Only the cache pool; however, it is only CRC Error Count issues which I have read could be due to bad sata cables. I ordered replacement ones in which will hopefully help. I am rebuilding the dead drive with a replacement now. I was wrong about the dead drive being a Seagate barracuda by the way. It’s a Seagate ironwolf which should be better quality than a barracuda. Also, I ran a pre clear on the dead drive for fun and it just finished. Here’s the finished status preview: #################################################################################################### # Unraid Server Preclear of disk Z730W84C # # Cycle 1 of 1, partition start on sector 64. # # # # Step 1 of 6 - Pre-read verification: [6:27:17 @ 129 MB/s] SUCCESS # # Step 2 of 6 - Erasing the disk: [6:21:54 @ 130 MB/s] SUCCESS # # Step 3 of 6 - Zeroing the disk: [5:48:43 @ 143 MB/s] SUCCESS # # Step 4 of 6 - Writing Unraid's Preclear signature: SUCCESS # # Step 5 of 6 - Verifying Unraid's Preclear signature: SUCCESS # # Step 6 of 6 - Post-Read verification: FAIL # # # # # #################################################################################################### # Cycle elapsed time: 18:38:14 | Total elapsed time: 18:38:14 # #################################################################################################### #################################################################################################### # S.M.A.R.T. Status (device type: default) # # # # ATTRIBUTE INITIAL STATUS # # Reallocated_Sector_Ct 1000 - # # Power_On_Hours 33334 - # # End-to-End_Error 0 - # # Reported_Uncorrect 37 - # # Airflow_Temperature_Cel 36 - ->Failed in Past<- # # Current_Pending_Sector 800 - # # Offline_Uncorrectable 800 - # # UDMA_CRC_Error_Count 0 - # # # #################################################################################################### # # #################################################################################################### In case that is hard to read, here’s a screenshot: and here are the errors from the log: preclear_disk_Z730W84C_25180.txt looks like it’s a goner. After only 3 years.
  7. Thanks Kilrah. Wondering if the diagnostic files show anything else that may be going on that I can address prior to doing a rebuild.
  8. And here are the attributes for the failing drive.
  9. I wanted to pull the diagnostics file before updating to 11.1. Here's the one I just pulled after updating. tower-diagnostics-20221007-0725.zip
  10. Thanks Truro! I had no idea you responded until now. I used to get emails for responses and even marked this as follow. Attached is my diagnostics file. I greatly appreciate the help. tower-diagnostics-20221007-0648.zip
  11. Hi there, Apologies for my ignorance. Is it safe to assume that the attached smart report for a disabled drive is a dead drive that should be replaced? Also, what part of it should I be looking at to tell that it is a bad drive? Lastly, I probably bought this drive along with quite a few other of the exact brand and size (Seagate Barracuda 3TB) over the course of maybe 1 year around 3 or 4 years ago and this is the 2nd that I've had issues with. Am I ignorant to assume that they should last longer? I switched to buying 8TB WD Elements/MyBook for the last bunch of drives since they started coming down in price a few years ago. I also believe that they are higher quality WD White drives than the desktop based Barracudas. Anyways, Thanks in advance for any help with the above questions! tower-smart-20221004-0900.zip
  12. macOS Big Sur 11.2.3 is 071-14766. Bear in mind, it does take awhile to download though. check the logs in: mnt/user/appdata/macinabox/macinabox/macinabox_BigSur.log
  13. Hi. I am not sure what is happening here. I upgraded through the gui and rebooted. Monitor shows kernel panic. I can boot in safe mode but I'm not sure what's going on here. Diagnostics attached. Thanks so much for your help in advance! tower-diagnostics-20210306-2347.zip
  14. So I kind of figured it out. Under "Local tunnel firewall" I entered my lan subnet and "Deny". The only problem is that my UnRAID server is in that subnet and I still have access to it. Even if I put the UnRAID IP in there, it still allows it through. Obviously because that's the tunnel address. I assume there's a way to do this that I'm just not seeing. Any help would be greatly appreciated. (I'm trying to provide my family with a remote PiHole but don't want them to have access to my UnRAID IP). Thanks!
  15. This is great! Is it possible to create a client who has remote tunnel access to the internet but no LAN access? ie. Same public IP?