cbr600ds2

You have to click apply to get it running...

The green is the link. when you switched it to yes did the apply button light up?

Has anyone had it where the place where you are grabbing NZB's from says you are grabbing a bunch of files but you haven't grabbed anything in your folders or anything in your sab?

You clicked done after switching it to yes? The link will show up above the unBalance v5.6.3.

Thanks...my dumb ass didn't even look.

am I getting these temp files because it updates Handbrake when the system is running? I thought it was because UD was being updated but its not that. Wonder if there's a way to not have the system update while a conversion is going on.

Ok thanks! I'll try it.

Curious if anyone is running into the same issue - In the docker page the version is displaying a broken chain and saying not available. I just wanted to let somebody know since I didn't see a post on it. Just happened overnight.

Oh ok. thanks!

Sounds like a winner. I'll try it out tonight Thanks!

Ran it, no errors but unbalance is giving me the same warning/error

Ok if I run newperms but exclude the appdata share (because of the warning) everything should be fine, right?

I have my handbrake write to an unassigned device drive and it created a temp folder (no problems) but now its done doing what it does and it didn't delete the temp folder and I can't delete it from Windows explorer. I tried looking through krusader but can't seem to find it through there. Any idea where it is to delete it (my OCD is killing me)

Hello! I get these errors when planning a move - if I run the docker safe new permissions then that should fix my issues? Any issues I can foresee? I'm trying to move files so I can format data drives but don't want to lose any information.

I didn't see the answer but you seem to be using the SAS expanders in PCIe slots. Would speed change if you powered via molex and not plugged in? I'm guessing you'd be limited by the HBA card and the HDD or am I way off?

Just rebuilt the server. from the ground up.

update - I went and bought 32 gb of ddr4 3600 ram and like an idiot did the rebuild in normal mode. got to 66% and then it crashed. tried it again in safe mode and now it wont go over 12% thinking of getting a new mb/cpu today. urgh. errors were the same call trace

I'm not quite sure how else to configure the memory- I've got 4 sticks of DDR4-3200 8GB each stick. I've only got 4 slots so I'm using all of the slots. the two sticks I had both memtested fine no errors in 24 hour runs for each stick singularly. Do you think the CPU went bad?

Ok so it stopped being approximately at 37.5. I have the last 2 successful diagnostics pulls and then the last syslog. This is what its showing skynet-diagnostics-20200911-1325 30%.zip skynet-syslog-20200911-1837.zip skynet-diagnostics-20200911-1321.zip

Ok. will do.

Just for S&G's I actually turned off Dockers and the gui is still responsive. bad thing is it's slowed to a crawl and won't let me pull diagnostics. I did grab every 10% so here's the diags from the 40% and I included the syslog that it let me download at 47.5 which its doing now...slowly. hahaha...I still have it running (crawling) skynet-syslog-20200910-2315 47.5%.zip skynet-diagnostics-20200910-1404 40%.zip

oh sorry, I guess I meant to say rebuilding FROM parity. Yikes, what a noob move. I can run it with that disk emulated and it runs fine. I can't access the command line or ping the server when its in this locked up state but if restart I can do damn near anything. I thought it was a memory thing so I shut off all dockers from autostarting but no issues with the dockers. I don't run any VM's even though I have shares/stuff like that from Spaceinvader's walk throught but I don't really use it for that. You think its a jacked up drive? The messy part is if I restart and even if I have the setting where it will write syslog errors to the zip drive it never writes anything. Should I try to do that again?

Left it running over night to see if it was just a gui issue but still not able to get in to the GUI and I can't do anything with attached Mouse and keyboard. Screen stills stopped at 4.4%

I found this post and was curious if its just the gui being stupid but screen is also froze since I started in Safe mode. Looking for a way to start/monitor parity check via command line -

this is the original post. Started it up in Safe mode w/ GUI and started rebuilding parity. Got to 4.4% and then you can't get back into gui. I grabbed this just as I started the parity rebuild. skynet-diagnostics-20200908-1708.zip