wildchild22

I assume only the LSI D3307-A12 can be flashed to IT mode. Or do I need to flash the expander to IT mode as well? I cannot find IT mode firmware for the expander. I only see one firmware file to use.

I am wondering if this is a good choice to add more drives to my unraid server. LSI D3307-A12 +82885T 12G RAID JBOD LSISAS3008 PCI 3.0 https://www.ebay.ca/itm/175115797350 It seems reasonable priced but I do not want to have to buy twice.

Thanks a lot for the help!

I have a spare SuperMicro H8DME-2 Dual 6 Core Opteron board with 2 cpus 12 cores and ram. I want to turn this into an unraid downloading machine and run a few basic vm's. Such as pi-hole, tailscale, nzbget and transmission. I see it has 2 pci express x8 slots. It seems it is pci 1.0 so 2000MB/s max so I want to buy a gen3 nvme 4 tb m2 drive and put it in a pci-express adapter. I also will install a mellonox 10 gb ethernet card in the other slot. My question is will this allow me to max out the nvme and ethernet? Or is the hardware too old and ready for the trash.

Please read the last page. This is not correct. Transcoding in RAM stopped working around Plex 0.9.14. See the other comments on this page. For more info on moving the transcoding directory, see: https://lime-technology.com/forum/index.php?topic=40937.msg419495#msg419495

How can we install an old plex docker image that works with ram transcoding? I do not care about new features. I would rather have an old working version for transcoding to ram.

there is no working docker with transmission with a rss feed or flex get.

How do we install this? I cannot get it to start.

I am requesting this as no other torrent client for unraid has rss feeds to auto download.

Hey there I am using your transmission plug-in. Is there anyway to make the transmission auto-read the settings.jason file every 5 mins or so? As I am adding torrents to a watch file but the only way they will add in transmission is if I start and stop my transmission via the webinterface. Here is my settings incase its needed { "alt-speed-down": 50, "alt-speed-enabled": false, "alt-speed-time-begin": 0, "alt-speed-time-day": 0, "alt-speed-time-enabled": false, "alt-speed-time-end": 0, "alt-speed-up": 50, "bind-address-ipv4": "0.0.0.0", "bind-address-ipv6": "::", "blocklist-enabled": false, "blocklist-url": "", "cache-size-mb": 4, "dht-enabled": false, "download-dir": "/mnt/user/torrents/download", "download-queue-enabled": true, "download-queue-size": 5, "encryption": 1, "idle-seeding-limit": 30, "idle-seeding-limit-enabled": false, "incomplete-dir": "/mnt/user/torrents/download", "incomplete-dir-enabled": false, "lazy-bitfield-enabled": true, "lpd-enabled": false, "message-level": 2, "peer-congestion-algorithm": "", "peer-id-ttl-hours": 6, "peer-limit-global": 240, "peer-limit-per-torrent": 60, "peer-port": 51413, "peer-port-random-high": 65535, "peer-port-random-low": 1024, "peer-port-random-on-start": false, "peer-socket-tos": "default", "pex-enabled": false, "pidfile": "/var/run/transmission/transmission.pid", "port-forwarding-enabled": true, "preallocation": 1, "prefetch-enabled": 1, "queue-stalled-enabled": true, "queue-stalled-minutes": 30, "ratio-limit": 2, "ratio-limit-enabled": false, "rename-partial-files": true, "rpc-authentication-required": false, "rpc-bind-address": "0.0.0.0", "rpc-enabled": true, "rpc-password": "{638398c12462903d0fd783165f34919b920517d4qdHDqARp", "rpc-port": 9091, "rpc-url": "/transmission/", "rpc-username": "", "rpc-whitelist": "127.0.0.1", "rpc-whitelist-enabled": false, "scrape-paused-torrents-enabled": true, "script-torrent-done-enabled": false, "script-torrent-done-filename": "", "seed-queue-enabled": false, "seed-queue-size": 10, "speed-limit-down": 100, "speed-limit-down-enabled": false, "speed-limit-up": 100, "speed-limit-up-enabled": false, "start-added-torrents": true, "trash-original-torrent-files": false, "umask": 18, "upload-slots-per-torrent": 15, "utp-enabled": true, "watch-dir": "/mnt/user/watch", "watch-dir-enabled": true }

I have 2 unraid servers. Identical hardware. 1 server cache drive and mover runs normally. Server 2 the mover script crashes unraid bad Any ideas? I have attached the log. The test file is a small txt file I made for testing the mover scipt. syslog22.zip

I am sure this is covered but I cannot find it. I want to have 2 accounts. Guest and mine (root) I want to only have my server list disk1 disk2 etc for everyone (Not export the contents). But I want everyone but me to only have read and write access. I do not want them to be able to delete files from the disks. How do I do this? I am afraid someone will delete something by mistake.

Thanks for the help so far. So the progress I made so far I got the data "Fixed and mounted the drive" but the files are damaged So then I did the trust the parity procedure and moved disc 13 to the cache position and the drive contents seem fine even though I though the parity was incorrect. So now I am going to copy the contents from the parity disc 13 to another drive on my server. Then once that completes I will move disc 13 back to the normal position and rebuild the data. Then I am guessing I will need reiserfsk --check to ensure the drive is correct and then test some of the contents. And then I can recheck parity. Does this seem like the best option??

Here is Partition info. Disk /dev/sdq: 1000.2 GB, 1000204886016 bytes 1 heads, 63 sectors/track, 31008336 cylinders Units = cylinders of 63 * 512 = 32256 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdq1 2 31008336 976762552+ 83 Linux Partition 1 does not end on cylinder boundary.

Here is the smart report smartctl 5.40 2010-10-16 r3189 [i486-slackware-linux-gnu] (local build) Copyright © 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F1 DT series Device Model: SAMSUNG HD103UJ Serial Number: S13PJDWQ812999 Firmware Version: 1AA01113 User Capacity: 1,000,204,886,016 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 3b Local Time is: Wed Jul 24 19:21:15 2013 NDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (11733) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 196) minutes. Conveyance self-test routine recommended polling time: ( 21) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0007 076 076 011 Pre-fail Always - 7960 4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 919 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0 8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail Offline - 0 9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 31142 10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 1 11 Calibration_Retry_Count 0x0012 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 172 13 Read_Soft_Error_Rate 0x000e 100 100 000 Old_age Always - 0 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0033 025 025 000 Pre-fail Always - 75 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 063 046 000 Old_age Always - 37 (Min/Max 30/37) 194 Temperature_Celsius 0x0022 055 045 000 Old_age Always - 45 (0 28 45 30) 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 1879 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 100 100 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 1 201 Soft_Read_Error_Rate 0x000a 253 253 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.

Hi there I am trying to get the data off disc 13. I do not think the parity is correct so I want to try and get the data off. What do I need to do next? I have copied and pasted the output from reiserfsck. Will read-only check consistency of the filesystem on /dev/md13 Will put log info to 'stdout' Do you want to run this program?[N/Yes] (note need to type Yes if you do):Yes The problem has occurred looks like a hardware problem. If you have bad blocks, we advise you to get a new hard drive, because once you get one bad block that the disk drive internals cannot hide from your sight,the chances of getting more are generally said to become much higher (precise statistics are unknown to us), and this disk drive is probably not expensive enough for you to you to risk your time and data on it. If you don't want to follow that follow that advice then if you have just a few bad blocks, try writing to the bad blocks and see if the drive remaps the bad blocks (that means it takes a block it has in reserve and allocates it for use for of that block number). If it cannot remap the block, use badblock option (-B) with reiserfs utils to handle this block correctly. bread: Cannot read the block (2): (Input/output error). Aborted (core dumped) root@Tower:~#

No it works fine without simplefeatures. Since simplefeatures is still crashed I installed unmenu and that is working fine. Not sure the issue. Bizarre - I'm running an AMD server as my main unRAID server - not a problem. Do you get this issue without simpleFeatures installed on that server?

Same software exactly except one is intel based (the working one) and the non working one is amd.

I have 2 servers. On my tower 2 simplefeatures just stopped repsonding alltogether. Usually after 10-15 mins. I have tried installing multiple times and I cannot get it working on my tower2. I can still telnet or ssh in and my sabnzb and transmission are all available by the web but simplefeatures just stops working. Anyway to troubleshoot?? On tower it is working perfectly.

I did power down from the webgui. But I didnt stop the plugins before doing so.

that maybe it then. I installed ram and just powered it down without stopping the plugins.

I have sickbeard , sabnzb and also transmission running off my unraid server. I have them installed on disk 15 of my server. I am getting parity sync errors since I done this. Will having these running off an array drive instead of a cache drive do this??

What would the command be to run a long smart test on all 16 of my drives and output the results to a txt file? I cannot get a clean parity check so I expect one of the discs is causing it. I really would like it todo the check on all discs at once so It will not take days to complete. Thanks for the help

Well I removed everything and just left 192.168.123.104:3551 And it works!!!!!! So the correct settings are just 192.168.123.104:3551 or tower:3551 for the first line thanks for the help

I tried using towers ip which is 192.168.123.104 and dtill not working. Not sure what I am doing wrong. I am using the version installed in unmenu. apcupsd-3.14.3-i486-1kjz.tgz