[Port Forwarding to docker image question]

Good evening,

 

I am trying to figure out if I have things setup correctly. 

 

I currently am using Wireguard with Mullvad to have my entire Unraid server behind a VPN.

 

I have all my dockers setup as bridge.

 

I would like to forward a port from Mullvad to a container.  Right now I have a iptables PREROUTING entry that maps the external port that mullvad assigned to me to the internal IP and port of the docker image.

 

Is that the correct way to do it?  Or is there a better way?

 

Appreciate any and all information people are willing to share, 

 

Cheers,

 

Chris

[Remote access to Plex while using starlink]

What I have done thus far is this

 

I created a tunnel using Mullvad following the Wireguard guide below

 

https://forums.unraid.net/topic/84316-wireguard-vpn-tunneled-access-to-a-commercial-vpn-provider/

 

Then I went back to the Mullvad site and created a port forward for that connection

 

Then using a iptables line I found in the article below

 

https://yevhen.ca/running-a-plex-server-through-starlink-cgnat-with-mullvad-vpn/

 

I added it to Unraid using the terminal window substituting the port I received from Mullvad 

 

Once that was done I went into plex and set the external port to the port that was assigned to my from Mullvad and hit apply

 

With any luck it should show accessible.

 

This may not be the best way of doing it and I would welcome to hear what others have to say

 

Cheers,

 

Chris

[WireGuard quickstart]

Good afternoon,

 

 Currently searching for an option to my issue and hope wireguard might be the solution.

 

My only internet option currently is Starlink and due to CGNat I will not be able to access my plex server remotely.

 

Can this be used to allow external access to my plex server again?

 

Cheers,

 

Chris

[Remote access to Plex while using starlink]

Good afternoon all,

 

I have recently moved and my best bet for high speed internet was to start using my starlink dish as my main internet source.

 

Currently they are running CGNat for IP distribution and the IPv6 service is still not 100%.

 

What I would like to do is somehow connect to a service that allows me to assign a static IP to my Plex docker.

 

Does anyone have a recommendation on how to best do that?  Also what service would be best to suited for this?

 

Appreciate all the info that you can provide

 

Cheers,

 

Chris

[Didn't Receive Your Registration Key?]

Placed my order last night (Order number  492131842) 

 

Still haven't received a key for my purchase

[unRAID not detecting both M.2 drives]

Ok, I have cancelled the MP510 order.

 

@Benson are there nvme drives that just work?  

 

Samsung ?

HP EX920 ?

 

Noticed that there are a few firmware updates to the Phison E12 family of nvme drives (currently on 12.3) I wonder if any of the updates fixed the trim issues

 

Thanks

[unRAID not detecting both M.2 drives]

I have started my return with Amazon on the Adata drives.  I have ordered 2 Corsair MP510 to replace them.  Hopefully Corsair will be easier to deal with then Adata if issues arise

[unRAID not detecting both M.2 drives]

No through amazon

[unRAID not detecting both M.2 drives]

@Alabaster

 

I found this today

 

https://lkml.org/lkml/2019/7/15/57

 

Looks like it is for drives with the realtek controller like we have.

[unRAID not detecting both M.2 drives]

I am also having this same issue with 2 Adata XPG GAMMIX S5 256GB drives.  Both are seen in the BIOS but I see the following during system start up.

 

Jul 14 21:56:11 TheWatchtower kernel: nvme nvme1: ignoring ctrl due to duplicate subnqn (nqn.2018-05.com.example:nvme:nvm-subsystem-OUI00E04C).

Jul 14 21:56:11 TheWatchtower kernel: nvme nvme1: Removing after probe failure status: -22

 

Is there a config tweak that can be made or will this have to be added by the main dev team?

 

Alabaster where you able to get the issue sorted out?

 

Cheers,

 

Chris