Dudedawg
-
Posts
14 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Store
Gallery
Bug Reports
Documentation
Landing
Posts posted by Dudedawg
-
-
does this mean the Dell x520-da2 is not supported, hmmm it is an intel chipset
-
-
Settings for bond0:
Supported ports: [ ]
Supported link modes: Not reported
Supported pause frame use: No
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Other
PHYAD: 0
Transceiver: internal
Link detected: yesdriver: bonding
version: 5.10.28-Unraid
firmware-version: 2
expansion-rom-version:
bus-info:
supports-statistics: no
supports-test: no
supports-eeprom-access: no
supports-register-dump: no
supports-priv-flags: no
--------------------------------
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: on
Port: Twisted Pair
PHYAD: 2
Transceiver: internal
MDI-X: off (auto)
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000007 (7)
drv probe link
Link detected: yesdriver: e1000e
version: 5.10.28-Unraid
firmware-version: 1.8-5
expansion-rom-version:
bus-info: 0000:00:19.0
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: yes
--------------------------------
Settings for eth3:
Supported ports: [ FIBRE ]
Supported link modes: 10000baseT/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 10000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000007 (7)
drv probe link
Link detected: yesdriver: ixgbe
version: 5.10.28-Unraid
firmware-version: 0x8000095d, 19.5.12
expansion-rom-version:
bus-info: 0000:04:00.0
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: yes
--------------------------------
-
do you want the zipped file??
-
Hello folks, I changed my Mellanox sfp+ for a dual sfp+ (Dell x520-da2), however unraid shows up as one port 😞
is there something I need to do?
-
is there a way to do this monthly?
-
On 11/19/2019 at 9:05 AM, trurl said:
That is pretty far away from the default network.cfg. Try renaming it and reboot so the default can be regenerated, then go from there.
thank you so much, it worked like a charm
-
hi folks, I am having the same issue, ipv4 not set, when I loook into the config folder, what file am I to look for, is it the network.cfg as below
# Generated settings:
IFNAME[0]=""
DHCP_KEEPRESOLV="no"
DHCP6_KEEPRESOLV="no"
BONDNICS[0]="eth0 eth1 eth2 eth3"
BONDING_MODE[0]="1"
BONDING_MIIMON[0]="100"
BRNICS[0]="bond0"
BRSTP[0]="0"
BRFD[0]="0"
USE_DHCP[0]="yes"
IFNAME[1]="eth3"
PROTOCOL[1]="ipv4"
USE_DHCP[1]="no"
IPADDR[1]="19*.***.***.***"
NETMASK[1]="255.255.255.0"
GATEWAY[1]="192.168.123.123"
MTU[1]="9000"
SYSNICS="2" -
10gb sfp cards are pretty cheap now, a set of intel will cost around $100, best check on ebay for a more update price.
they will get you more than enough transfer speeds and easy to set up.
you can increase your speed on your windows machine with Jumbo Packet sizes, increase to max
and also your transmit and receive buffers, increase them to max
and on the bsd machine, your unraid, try the mtu to a higher number
-
Hello all, I have configured my dell power edge r610 to run Plex, now with the limited storage ability I had to find another source, so I built another machine running unraid and I have set it up, it shows up on the network on windows, I have transferred films over to the UnRaid and that is working ok,
on the web based plex on the R610 accessed over the network, I don't see it the drive space..
the operating system I am using on my Dell machine is Centos 7
spare machine has UnRaid
any help would be great
-
4 hours ago, nuhll said:
Then this is perfect. Its all point and click, massive loads of step by step videos and or other tutorials for nearly all aspects you might need later. And in worst case you can ask here or on reddit for help.
Also the biggest + is that unraid is just a one time cost. (how much better can it get?)
sounds so true, I am a big fan of one time cost... yaaaay!! lol
-
great and thanks for all your help, I am picking my storage server tomorrow, this will be fun
thank you again, I will try the trial first, I will most likely purchase it eventually, I am a noob user when it comes with server stuff,
-
Hello folks, hi, I am new here, I heard about you guys from Linus Tech Tips, and interested in the software however before I purchase it, I have some question I am sure you will be able to help,
I am soon to get myself a storage unit server, with some space on it, its for films for plex and maybe other applications, I have it running on Centos and its working fine, my question are, does Unraid run like an independent operating system on a bootable flash drive, will it work on any flash drive, and will I be able to add more storage later down the road
- does Unraid run like an operating system?
- what flash drives does it support?
- can I add more to the system
thank you for your time..
Dell x520-Da2 showing only one port - SOLVED -
in General Support
Posted
the modules are now both the intel, and its working now, thanks you folks.
you were right, that one was not the intel, it was the mellanox module, my bad
thanks again for your help.