flambot Posted December 26, 2020 Share Posted December 26, 2020 (edited) Greetings, How is everyone? Hope you're having good times. My server is currently running 6.7.2. I went to update the few plugins that I have (CA, cache_directories) and it would appear I can no longer do this from the GUI. It would seem that I need to be running 6.8.3. Is this the latest stable release? (This is what I've got ( "unRAIDServer-6.8.3-x86_64.zip") I have a very old server. I am wary of changing anything because I'm not in the position to build a new one. I worry about upgrading because of this and the fact my resources on the server aren't high. Do I need to keep upgrading?? It would seem I do because all the plugins change. I guess I should upgrade to 6.8.3. How is this done through the GUI (I've never done it through the GUI before). There doesn't appear to be anyway in the "Update OS" tab - or will it only show when the array is offline?? I saw this in a post "https://s3.amazonaws.com/dnld.lime-technology.com/stable/unRAIDServer.plg" to use the install plugin area. Will that work? I saw this "If you are running any 6.4 or later release, click 'Check for Updates' on the Tools/Update OS page." - but there is no button for this (perhaps need to stop the array?) Many thanks Edited December 26, 2020 by flambot Quote Link to comment
Squid Posted December 26, 2020 Share Posted December 26, 2020 7 hours ago, flambot said: I guess I should upgrade to 6.8.3. How is this done through the GUI (I've never done it through the GUI before). There doesn't appear to be anyway in the "Update OS" tab - or will it only show when the array is offline?? Tools Tab 7 hours ago, flambot said: I saw this in a post "https://s3.amazonaws.com/dnld.lime-technology.com/stable/unRAIDServer.plg" to use the install plugin area. Will that work? Yes if the above doesn't work. Quote Link to comment
flambot Posted December 26, 2020 Author Share Posted December 26, 2020 Thanks Squid. Really appreciate the insight. Quote Link to comment
trurl Posted December 26, 2020 Share Posted December 26, 2020 Besides plugins not being compatible with old versions. support for old versions can be difficult since it isn't what people on the forum are using. Quote Link to comment
flambot Posted December 26, 2020 Author Share Posted December 26, 2020 Tried for an upgrade this morning and it failed. There is NO button in the Tools>OS page (that shows as a button) I have to assume the Update OS Text at top left is it. I got a message as below. I am now suspicious that the server does not have connection to the internet. We have just changed our ISP - which meant a new router/modem. The new modem/router is registering the server (and I can login into it through the GUI), but there is NO IP address in the modem interface after the name of the server - but there is after the name of every other computer on the network. My server has a static IP, which I left unchanged, but I had to change the gateway. I am suspicious that the static IP is NOT in the correct IP range for the new modem/router (which uses a slightly different range ".178" VS ".1"). I have just found a panel in the new modem/router interface where you can add a new device with a static IP. One thing I find a little confusing is the new modem/router has both an IPv4 and a IPv6 setting for each device. Chewing my nails 🤔 Any comments before I do this. Quote Link to comment
trurl Posted December 27, 2020 Share Posted December 27, 2020 Just let your server use DHCP and it will get an IP from the router that will be compatible with the rest of your network. Quote Link to comment
flambot Posted December 28, 2020 Author Share Posted December 28, 2020 Finally got it sorted out. @Constructor - you are correct. That would be the easy way, but I putty into the server and knowing the IP is a critical part. I found out the same thing had happened to our HTPC (also a static IP and running linux - so putty again) and couldn't connect at all. I tried everything. In the end I connected back to the old router and bingo - away we went. The new router has a different IP range, than the old one as I suspected. I even tried to re-route the old one to the new one but it wouldn't work. Tech is sometimes way too complicated - unless your a genius! Doesn't help that I'm an old-fogy with a brain and memory that isn't as sharp has it once was. While I write everything down, it's still a major effort to sort it all out again. Once I had the IP's all sorted out, the server was connected again to the internet - so I could upgrade via the gui. First time for me. Only thing that could be an issue - I have only a 512mb USB, so the old version takes up quite a lot of space. I'll see how the new version goes, then I'll backup and then delete the previous version off the USB drive. Hopefully this won't be an issue. Appreciate the comments. Thanks Quote Link to comment
trurl Posted December 28, 2020 Share Posted December 28, 2020 15 hours ago, flambot said: @Constructor @Advanced Member I always reserve IPs by MAC address in the router. That way everything is managed in one place and I always know what the IPs are. Quote Link to comment
flambot Posted December 28, 2020 Author Share Posted December 28, 2020 @trurl - sorry about that. I just realised I grabbed the wrong name from your post. Apologies. 3 hours ago, trurl said: @Advanced Member I always reserve IPs by MAC address in the router. That way everything is managed in one place and I always know what the IPs are. I think I've done that myself (in fact, the router does it's setup using MAC address. My old router wasn't this flash in the interface. Both have been supplied by the ISP - meaning cheap😉 Quote Link to comment
trurl Posted December 28, 2020 Share Posted December 28, 2020 37 minutes ago, flambot said: @trurl - sorry about that. I just realised I grabbed the wrong name from your post. Apologies. You're certainly not the first. But a little more advice on using the forum. In order to actually notify someone when you type @ followed by their username, you have to actually select from the matching choices. Just typing @flambot doesn't get it done. You have to do @flambot Quote Link to comment
flambot Posted December 29, 2020 Author Share Posted December 29, 2020 @trurl - you are right. I didn't wait long enough to see the menu pop up. Doh! Thanks Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.