PeteB Posted April 22, 2021 Share Posted April 22, 2021 (edited) Hi All, After updating to 6.9.1 my unraid server won't boot into GUI mode. I've attached my diagnostics file. All help greatly appreciated. It boots to a blank after all the boot messages come up it ends up with a blank screen with a flashing cursor in the top left hand corner. The web gui is available by browsing to the server and it is functioning correctly, it's just the console with problems. Pete moose-diagnostics-20210422-1449.zip Edited April 22, 2021 by PeteB Quote Link to comment
PeteB Posted April 22, 2021 Author Share Posted April 22, 2021 (edited) I've seen these two posts, but I haven't changed anything apart from upgrading to 6.9.1. Thought I should check before tinkering. ps: I don't have any nvidia plugin installed Edited April 22, 2021 by PeteB Quote Link to comment
PeteB Posted April 24, 2021 Author Share Posted April 24, 2021 Hi. Is there anyone who could give me some pearls of wisdom on this please? Quote Link to comment
JorgeB Posted April 24, 2021 Share Posted April 24, 2021 See this thread, several solutions there: Quote Link to comment
45leopard Posted April 24, 2021 Share Posted April 24, 2021 (edited) I'm having same issue.... cannot boot GUI mode. I have tried various settings on BIOS to no avail. So far I have not tried legacy boot, since my boot flash drive is UEFI only. Not sure why that would work, but its the only thing I haven't checked. I have Asus X570 Tuf MB with AMD 3400G processor. CSM enabled. Running 6.9.2 version Unraid. Any help would be appreciated ... or is this an Unraid bug. I'd like to get it fixed so I can use Krusader file manager to make degoogling easier. SOLVED.... Installed "radeon top" plugin which enables 'amdgpu' kernel module. So anyone else having this issue and using AMD cpu/graphics... try installing "Radeon Top" plugin. Edited April 24, 2021 by 45leopard SOLVED ISSUE 1 Quote Link to comment
PeteB Posted April 27, 2021 Author Share Posted April 27, 2021 This isn't solved. I have built in graphics (not a radeon). The server still does not boot into the GUI. The following commands work, but need to be issued on every reboot: Ctrl - Alt - F1 modprobe i915 /etc/rc.d/rc.4 Quote Link to comment
sunbear Posted May 27, 2021 Share Posted May 27, 2021 I'm pulling my hair out over here. My GUI also stopped working. I don't use any NVIDIA or INTEL special drivers and have an integrated Radeon R7 APU. Can someone please help me figure out how to get my GUI back. Quote Link to comment
sunbear Posted June 5, 2021 Share Posted June 5, 2021 Can anyone help me out? I feel like I was the only person with this issue that WASN'T trying to use any of the drivers. I just need to be able to access my GUI so I can setup an rclone config. (would be nice to have it for emergencies too) Quote Link to comment
PeteB Posted June 13, 2021 Author Share Posted June 13, 2021 Still broken for me too! I was hoping there might be some words of wisdom on the forum, but I suspect I'm just going to have to live with thus bug. Sent from my SM-G970F using Tapatalk Quote Link to comment
SimonF Posted June 13, 2021 Share Posted June 13, 2021 4 hours ago, PeteB said: Still broken for me too! I was hoping there might be some words of wisdom on the forum, but I suspect I'm just going to have to live with thus bug. Sent from my SM-G970F using Tapatalk Have you tried installing the Intel GPU top plugin? Quote Link to comment
SimonF Posted June 13, 2021 Share Posted June 13, 2021 On 5/27/2021 at 2:46 AM, sunbear said: I'm pulling my hair out over here. My GUI also stopped working. I don't use any NVIDIA or INTEL special drivers and have an integrated Radeon R7 APU. Can someone please help me figure out how to get my GUI back. Have you tried installing the Radeon top plugin? Quote Link to comment
6of6 Posted June 13, 2021 Share Posted June 13, 2021 I read this because its marked [SOLVED]. Clearly, the OP didn't mark it solved. Who moderates this forum? On topic... I've never been able to make GUI boot work. Has anyone? 6. Quote Link to comment
JorgeB Posted June 13, 2021 Share Posted June 13, 2021 1 hour ago, 6of6 said: the OP didn't mark it solved. Who moderates this forum? I did because of this: On 4/24/2021 at 2:22 PM, 45leopard said: SOLVED.... Installed "radeon top" plugin which enables 'amdgpu' kernel module. So anyone else having this issue and using AMD cpu/graphics... try installing "Radeon Top" plugin. My mistake since it wasn't posted by the OP, removed SOLVED. 1 Quote Link to comment
PeteB Posted July 23, 2021 Author Share Posted July 23, 2021 Ok...This problem is still there. To recap, no changes to my system apart from an upgrade to 6.9.1 and now the local console won't boot into GUI mode. Any help or pointers please. Quote Link to comment
JorgeB Posted July 23, 2021 Share Posted July 23, 2021 Did you try installing the intel-gpu-top plugin like mentioned in the other thread above? Quote Link to comment
DerekV Posted August 3, 2021 Share Posted August 3, 2021 I have my unraid running on ESXi and wanted to passthru a physical NIC instead of using the trunked VLAN. Not so easy to do via the web GUI and the issue with two NIC on the same subnet. In troubleshooting I could need boot into the GUI in either the ESXi console or on a standalone PC. For me removing "modprobe i915" from the go file got me into the GUI on the stand alone PC and update the network.cfg, but I still cant boot from the ESXi console, could be plop or something else. So maybe this helps others as a workaround on standalone or the developers to look into why the modprode kills the video drivers. I will look around and see if I can get the plopexec working with the GUI boot option. Quote Link to comment
trurl Posted August 3, 2021 Share Posted August 3, 2021 3 hours ago, DerekV said: unraid running on ESXi Not supported but there is a "Virtualizing Unraid" subforum where others that are running Unraid as a VM help each other. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.