Drive disable with Errors, new m.2 SATA Controller JMB585


sonic6

8 posts in this topic Last Reply

Recommended Posts

Hey,

 

does someone tested KALEA-INFORMATIQUE - M.2 (PCIe 3.0 M oder B+M Key) mit 5 Port SATA III 6G Controller Karte. 5X SATA 6G. CHIPSATZ JMB585 with Unraid?

 

I installed two of this on weekend and ended up getting Errors on one drive.

Parity Re-build runs fine, but if i delete or write files on my 10TB WD Red, unraid detects Errors and disable the drive.

 

After the first Errors, i saw, that the second m.2 SATA controller wasn't good connected to the m.2 Port, so i fixed this.

 

On the first m.2 SATA controller are two cache SSD connected. No problem.

On the second are the following drives conntected:

Parity 10TB WD RED

Drive1 4TB WD RED

Drive2 10TB WD RED

 

I switched the m.2 SATA controller, i switched the m.2 slots, i changed ALL SATA Cabels.

 

Now i am unsure if Drive2 or the m.2 SATA controller is bad.

 

Board: ASRock H470M-ITX/AC

 

 

Here two Diagnostics, maybe it will help.

unraid-1-diagnostics-20210502-1737.zip unraid-1-diagnostics-20210503-0651.zip

Edited by sonic6
Link to post

JMB585 usually works fine with Unraid.

 

1 hour ago, sonic6 said:

I switched the m.2 SATA controller, i switched the m.2 slots, i changed ALL SATA Cabels.

Not clear if you then rebuilt the disk and it happen again, because once a disk is disable it needs to be rebuilt.

 

Link to post
11 minutes ago, sonic6 said:

i did a rebuild.

OK, just wanted to make sure since some users expect replacing cables/controller fixes a disable disks.

 

First diags show a successful rebuild, second ones show a rebuild in progress, there are some ATA errors though, you say it's always the same disk that gets disable, even if you connect it to a different controller?

 

 

Link to post

Till now i just tried the two m.2 data controller. 

When the current rebuild is finish tomorrow I will try some writing on the 4TB WD Red. If this also failed. Then I think the m.2 controller ish the source of the problem. If there are no errors, I will try the M1015 HBA.

Link to post

So, today ich switched back to my old M1015 HBA. After rebuild my 10TB WD Red the Array works fine since 8 hours. I deleted some files and does some writings on the array to Disk1 and Disk2 and i got no Errors again.

 

Looks like the m.2 Sata Controller won't work with my System.

Link to post
19 minutes ago, sonic6 said:

Looks like the m.2 Sata Controller won't work with my System.

Or the JMB controller doesn't like that specific disk model, if it was only that disk you can try connecting it to another controller instead, like the onboard SATA ports.

Link to post
2 hours ago, JorgeB said:

Or the JMB controller doesn't like that specific disk model, if it was only that disk you can try connecting it to another controller instead, like the onboard SATA ports.

Disk2 and Parity are the same WD Red 10TB (WDC_WD100EFAX) and the Errors only appears on Disk2. I also got some "199UDMA CRC error count" on Disk1 (WDC_WD40EFRX) over the last week i was using the JMB585.

I am too afraid losing data from my disk, so i don't did more tests with the JMB controller. So i'm sorry :S

Edited by sonic6
Link to post

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.