alturismo Posted December 14, 2022 Share Posted December 14, 2022 22 minutes ago, jj1987 said: Bei mir stehen alle USB controller auf ASPM enabled. Auch der an dem der UNRAID Stick hängt. Kann damit also erstmal nichts zu tun haben glaub ich Dir, ich kann nur sagen, ohne verbaute GPU's = hohe C States, mit verbauten GPU's = C3 Ende ... egal in welchem Zustand sich die GPU's befinden. Ist jedoch nur meine ganz persönliche Erfahrung, sowie PCIe Karten verbaut sind war hier immer "Essig" mit C10 ... Quote Link to comment
Jogi65 Posted December 14, 2022 Share Posted December 14, 2022 16 hours ago, jj1987 said: Punkt 4 sagt mir gerade ehrlich gesagt nichts. Punkt 7 ist ein extra SATA Controller (die sind unter Stromsparaspekten immer... suboptimal), brauchst du alle Ports? Sonst den Mal im uefi deaktivieren Habe jetzt nochmal geschaut. Dadurch das ich 5 Platten im Gehäuse habe, brauche ich diesen SATA-Controller. Sobald ich ihn im BIOS deaktiviere, fehlen mir zwei Platten. Ohne diesen Controller stehen mir nur 4 SATA-Ports zur Verfügung. Selbst wenn ich die Platten umsteckte, fehlt mir also immer noch ein weiterer Port. 🤔 Quote Link to comment
sonic6 Posted December 14, 2022 Share Posted December 14, 2022 2 hours ago, alturismo said: ich kann nur sagen, ohne verbaute GPU's = hohe C States, mit verbauten GPU's = C3 Ende so sieht es bei mir auch aus... über weihnachten werde ich mal meine m.2 zu pcie adapter und pcie riser ausbauen, dann könnte ich mal gegen testen. glaube aber da funkt mir dann noch mein HBA dazwischen. Quote Link to comment
jj1987 Posted December 14, 2022 Share Posted December 14, 2022 3 hours ago, alturismo said: glaub ich Dir, ich kann nur sagen, ohne verbaute GPU's = hohe C States, mit verbauten GPU's = C3 Ende OK, da ist natürlich was dran. Wobei ich meine dass es uU noch davon abhängt wie der pcie Slot angebunden ist, also via Chipsatz oder direkt von der CPU Quote Link to comment
mgutt Posted December 14, 2022 Share Posted December 14, 2022 On 12/13/2022 at 3:20 PM, Jogi65 said: MSI MAG Mortar WiFI Intel B660 Boards mit extra Controllern sind nie eine gute Basis für ein effizientes Setup. Ich würde es eher mit einem ASUS Pro Q670M oder ASRock B660M Steel Legend probieren. Quote Link to comment
Jogi65 Posted December 14, 2022 Share Posted December 14, 2022 Ich sehe schon, man lernt nie aus 😉 Habe ich noch eine Chance aus dem Board/ der Konfiguration etwas mehr Spar-Potenzial zu holen? Quote Link to comment
Jogi65 Posted December 15, 2022 Share Posted December 15, 2022 14 hours ago, mgutt said: Ich würde es eher mit einem ASUS Pro Q670M oder ASRock B660M Steel Legend probieren. Habe mal geschaut, das ASRock fällt auch raus, da es die gleiche Konstellation wie mein MSI hat. Bleibt nur das ASUS. Da scheinen die 6 SATA-Port tatsächlich über den Q670-Chip zu laufen. Meinst Du, ich habe noch andere Möglichkeiten oder liegt es tatsächlich primär an dem 2. SATA-Controller? Quote Link to comment
mgutt Posted December 15, 2022 Share Posted December 15, 2022 Sagen wir so. Garantiert ist nie was. Es kann von Board zu Board anders laufen. Was du evtl vorher noch mal testen solltest, ist Ubuntu zu booten / installieren. Und dann dann auch noch mal mit powertop probieren. Wenn auch da C3 das Limit ist, kann man das Board denke ich abhaken. Quote Link to comment
Jogi65 Posted December 15, 2022 Share Posted December 15, 2022 Alles klar, probiere ich mal am Wochenende und gebe Rückmeldung. Erstmal Danke! Quote Link to comment
Jogi65 Posted December 21, 2022 Share Posted December 21, 2022 (edited) Wollte mich wenigstens kurz melden. Der Jahresendstress hat mich leider voll im Griff. Werde den Test mit Ubuntu wohl erst zwischen den Jahren mache können. Melde mich, wenn ich neue Werte habe. Euch schöne Weihnachtsfeiertage und erst einmal Danke für die Unhterstützung! 🎅🎄 Edited December 21, 2022 by Jogi65 Quote Link to comment
alturismo Posted December 25, 2022 Share Posted December 25, 2022 On 12/14/2022 at 2:04 PM, jj1987 said: Bei mir stehen alle USB controller auf ASPM enabled. Auch der an dem der UNRAID Stick hängt. Kann damit also erstmal nichts zu tun haben ich hab mir mal den Spaß gegeben und meine Conf umgestellt usw ... unraid hängt hier jetzt am Intel Controller und jetzt hab ich 2 disabled USB Controller also hier bringt es leider nichts ... Versuch war es wert root@AlsServer:~# lspci -vv | awk '/ASPM/{print $0}' RS= | grep --color -P '(^[a-z0-9:.]+|ASPM )' 00:01.0 PCI bridge: Intel Corporation 6th-10th Gen Core Processor PCIe Controller (x16) (rev 05) (prog-if 00 [Normal decode]) LnkCap: Port #2, Speed 8GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <256ns, L1 <8us LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes, Disabled- CommClk+ 00:1b.0 PCI bridge: Intel Corporation Device 43c2 (rev 11) (prog-if 00 [Normal decode]) LnkCap: Port #19, Speed 8GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <16us LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ 00:1b.4 PCI bridge: Intel Corporation Device 43c4 (rev 11) (prog-if 00 [Normal decode]) LnkCap: Port #21, Speed 8GT/s, Width x4, ASPM L1, Exit Latency L1 <16us LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ 00:1c.0 PCI bridge: Intel Corporation Device 43ba (rev 11) (prog-if 00 [Normal decode]) LnkCap: Port #3, Speed 8GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <16us LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+ 00:1c.4 PCI bridge: Intel Corporation Tiger Lake-H PCI Express Root Port #5 (rev 11) (prog-if 00 [Normal decode]) LnkCap: Port #5, Speed 8GT/s, Width x4, ASPM L1, Exit Latency L1 <16us LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ 00:1d.0 PCI bridge: Intel Corporation Tiger Lake-H PCI Express Root Port #9 (rev 11) (prog-if 00 [Normal decode]) LnkCap: Port #9, Speed 8GT/s, Width x4, ASPM L1, Exit Latency L1 <16us LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ 01:00.0 VGA compatible controller: NVIDIA Corporation GA102 [GeForce RTX 3080 Ti] (rev a1) (prog-if 00 [VGA controller]) LnkCap: Port #0, Speed 8GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <512ns, L1 <16us LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes, Disabled- CommClk+ pcilib: sysfs_read_vpd: read failed: No such device 01:00.1 Audio device: NVIDIA Corporation GA102 High Definition Audio Controller (rev a1) LnkCap: Port #0, Speed 8GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <512ns, L1 <4us LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes, Disabled- CommClk+ 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. Killer E3000 2.5GbE Controller (rev 06) LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ 03:00.0 Non-Volatile memory controller: Sandisk Corp WD Black SN750 / PC SN730 NVMe SSD (prog-if 02 [NVM Express]) LnkCap: Port #0, Speed 8GT/s, Width x4, ASPM L1, Exit Latency L1 <8us LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ 04:00.0 USB controller: ASMedia Technology Inc. ASM1042A USB 3.0 Host Controller (prog-if 30 [XHCI]) LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 unlimited LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+ 05:00.0 VGA compatible controller: NVIDIA Corporation GP106 [GeForce GTX 1060 6GB] (rev a1) (prog-if 00 [VGA controller]) LnkCap: Port #0, Speed 8GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <512ns, L1 <16us LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ 05:00.1 Audio device: NVIDIA Corporation GP106 High Definition Audio Controller (rev a1) LnkCap: Port #0, Speed 8GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <512ns, L1 <4us LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ 06:00.0 Non-Volatile memory controller: Samsung Electronics Co Ltd NVMe SSD Controller SM981/PM981/PM983 (prog-if 02 [NVM Express]) LnkCap: Port #0, Speed 8GT/s, Width x4, ASPM L1, Exit Latency L1 <64us LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ Quote Link to comment
jj1987 Posted December 25, 2022 Share Posted December 25, 2022 9 minutes ago, alturismo said: also hier bringt es leider nichts ... Versuch war es wert Ja liegt dann vermutlich tatsächlich an der Graka. Aber richtig: Versuch macht kluch😉 Quote Link to comment
SidM Posted December 29, 2022 Share Posted December 29, 2022 Nabend! Ich wollte seit dem Update von Unraid 6.9.2 auf jetzt 6.11.5 mal wieder in Powertop reinschauen und hab festgestellt dass das nicht mehr geht "command not found". Also hab ich hier nochmal nachgeschaut und auch gesehen das powertop jetzt in der Version 2.15 vorliegt und mit den dortigen Befehl installiert. Nur wird mir in der Konsole noch immer "command not found" angezeigt wenn ich powertop eingebe. Was mache ich falsch? Quote Link to comment
alturismo Posted December 29, 2022 Share Posted December 29, 2022 22 minutes ago, SidM said: Was mache ich falsch? du wirst es schon installieren müssen ... ich schätze du hattest vorher das Nerd Pack installiert was ex ist. entweder manuell, Nerd Tools glaube ich heißt der Nacholger oder un-get für Fortgeschrittene 1 Quote Link to comment
mgutt Posted December 30, 2022 Share Posted December 30, 2022 3 hours ago, SidM said: und mit den dortigen Befehl installiert. Pakete in extra werden erst bei einem Neustart installiert 😉 1 Quote Link to comment
SidM Posted December 30, 2022 Share Posted December 30, 2022 9 hours ago, mgutt said: Pakete in extra werden erst bei einem Neustart installiert 😉 Ja das war es! Dachte ich mir schon bald, wollte aber die Kiste gestern nicht Neu starten bzw. lief noch etwas. Danke! Quote Link to comment
fir3drag0n Posted January 4, 2023 Share Posted January 4, 2023 Mal eine kurze Frage: Sind C9/C10 auch erreichbar, wenn ein Monitor dranhängt? Quote Link to comment
Mibelosa Posted January 5, 2023 Share Posted January 5, 2023 Guten Abend, ich habe ein komplett neues System mit dem RM550x (2021) Netzteil, einem i5-13600K, DDR4 Speicher und nachdem mehrere Gigabyte Boards kaputt ankamen, schlussendlich leider ein MSI Z790-Pro Wifi DDR4 Board geholt. Als Platten sind bisher nur eine 980 Pro SSD und eine Sandisk SSD verbaut. Der Verbrauch liegt momentan bei 10,9-17W. Bei den C-States komme ich bis C6. Wenn ich powertop --auto-tune ausführe, kommt folgende Fehlermeldung: powertop: /lib64/libncursesw.so.6: no version information available (required by powertop) powertop: /lib64/libtinfo.so.6: no version information available (required by powertop) modprobe cpufreq_stats failed Loaded 0 prior measurements Cannot load from file /var/cache/powertop/saved_parameters.powertop File will be loaded after taking minimum number of measurement(s) with battery only RAPL device for cpu 0 RAPL device for cpu 0 Devfreq not enabled glob returned GLOB_ABORTED Cannot load from file /var/cache/powertop/saved_parameters.powertop File will be loaded after taking minimum number of measurement(s) with battery only Leaving PowerTOP Die App "Intel-GPU-TOP" habe ich schon geladen, allerdings konnte die die Fehlermeldung auch nicht beheben. Hat noch jemand eine Idee was ich machen kann, damit Autotune ohne Fehlermeldung durchläuft und ich C8-10 erreiche? Quote Link to comment
alturismo Posted January 5, 2023 Share Posted January 5, 2023 21 minutes ago, Mibelosa said: damit Autotune ohne Fehlermeldung durchläuft Nein, die sind auch einfach zu ignorieren und haben nichts mit den aktuellen c states zu tun, steht auch so mehrfach in diesem thread ... Quote Link to comment
mgutt Posted January 6, 2023 Share Posted January 6, 2023 On 1/5/2023 at 5:44 PM, Mibelosa said: Der Verbrauch liegt momentan bei 10,9-17W. Was sollen die Schwankungen?! Quote Link to comment
fir3drag0n Posted January 7, 2023 Share Posted January 7, 2023 22 hours ago, mgutt said: Was sollen die Schwankungen?! Liegt vermutlich an dem Bug in unRAID, wenn man das Webinterface auf hat? Quote Link to comment
jj1987 Posted January 7, 2023 Share Posted January 7, 2023 32 minutes ago, fir3drag0n said: Liegt vermutlich an dem Bug in unRAID, wenn man das Webinterface auf hat? Auf welcher Version bist du denn? Das ist seit Version 6.11. (oder sogar irgendeine 6.10.x?) behoben Quote Link to comment
cz13 Posted January 7, 2023 Share Posted January 7, 2023 4 minutes ago, jj1987 said: Auf welcher Version bist du denn? Das ist seit Version 6.11. (oder sogar irgendeine 6.10.x?) behoben Das Problem wurde mir 6.11.4 gefixt. Quote Link to comment
jj1987 Posted January 7, 2023 Share Posted January 7, 2023 1 hour ago, cz13 said: Das Problem wurde mir 6.11.4 gefixt. Oh, dachte das wäre schon länger her... Quote Link to comment
Bengon Posted January 7, 2023 Share Posted January 7, 2023 Ich habe das gleiche Problem,zwischen ca. 11-16 Watt schwankt es,manchmal auch mehr.Auch mit Browserfenster schließen und Terminalbefehlen wie hier vorgeschlagen wird es nur minimal besser.Habe auch einen Teststick versucht mit nur einer SSD als Laufwerk ohne Docker,Plugins oder VM auf anderer Hardware ,aber da habe ich das gleiche Phänomen Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.