Dudedawg Posted July 27, 2021 Share Posted July 27, 2021 (edited) Hello folks, I changed my Mellanox sfp+ for a dual sfp+ (Dell x520-da2), however unraid shows up as one port 😞 is there something I need to do? Edited July 30, 2021 by Dudedawg Quote Link to comment
JorgeB Posted July 28, 2021 Share Posted July 28, 2021 Please post the diagnostics: Tools -> Diagnostics Quote Link to comment
Dudedawg Posted July 28, 2021 Author Share Posted July 28, 2021 do you want the zipped file?? Quote Link to comment
Dudedawg Posted July 28, 2021 Author Share Posted July 28, 2021 Settings for bond0: Supported ports: [ ] Supported link modes: Not reported Supported pause frame use: No Supports auto-negotiation: No Supported FEC modes: Not reported Advertised link modes: Not reported Advertised pause frame use: No Advertised auto-negotiation: No Advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Auto-negotiation: off Port: Other PHYAD: 0 Transceiver: internal Link detected: yes driver: bonding version: 5.10.28-Unraid firmware-version: 2 expansion-rom-version: bus-info: supports-statistics: no supports-test: no supports-eeprom-access: no supports-register-dump: no supports-priv-flags: no -------------------------------- Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Auto-negotiation: on Port: Twisted Pair PHYAD: 2 Transceiver: internal MDI-X: off (auto) Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000007 (7) drv probe link Link detected: yes driver: e1000e version: 5.10.28-Unraid firmware-version: 1.8-5 expansion-rom-version: bus-info: 0000:00:19.0 supports-statistics: yes supports-test: yes supports-eeprom-access: yes supports-register-dump: yes supports-priv-flags: yes -------------------------------- Settings for eth3: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supported pause frame use: Symmetric Supports auto-negotiation: No Supported FEC modes: Not reported Advertised link modes: 10000baseT/Full Advertised pause frame use: Symmetric Advertised auto-negotiation: No Advertised FEC modes: Not reported Speed: 10000Mb/s Duplex: Full Auto-negotiation: off Port: Direct Attach Copper PHYAD: 0 Transceiver: internal Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes driver: ixgbe version: 5.10.28-Unraid firmware-version: 0x8000095d, 19.5.12 expansion-rom-version: bus-info: 0000:04:00.0 supports-statistics: yes supports-test: yes supports-eeprom-access: yes supports-register-dump: yes supports-priv-flags: yes -------------------------------- Quote Link to comment
itimpi Posted July 28, 2021 Share Posted July 28, 2021 10 minutes ago, Dudedawg said: do you want the zipped file?? Yes 1 Quote Link to comment
Dudedawg Posted July 28, 2021 Author Share Posted July 28, 2021 area51-diagnostics-20210728-1006.zip Quote Link to comment
JorgeB Posted July 28, 2021 Share Posted July 28, 2021 Jul 27 14:25:42 Area51 kernel: ixgbe 0000:04:00.1: failed to load because an unsupported SFP+ or QSFP module type was detected. Jul 27 14:25:42 Area51 kernel: ixgbe 0000:04:00.1: Reload the driver after installing a supported module. Quote Link to comment
Dudedawg Posted July 29, 2021 Author Share Posted July 29, 2021 does this mean the Dell x520-da2 is not supported, hmmm it is an intel chipset Quote Link to comment
JorgeB Posted July 30, 2021 Share Posted July 30, 2021 11 hours ago, Dudedawg said: does this mean the Dell x520-da2 is not supported, The quoted syslog mentions that the problem is the fiber module you're using in that port, it's not supported by the NIC. 1 Quote Link to comment
Dudedawg Posted July 30, 2021 Author Share Posted July 30, 2021 the modules are now both the intel, and its working now, thanks you folks. you were right, that one was not the intel, it was the mellanox module, my bad thanks again for your help. 1 Quote Link to comment
technoprenerd Posted June 7, 2022 Share Posted June 7, 2022 On 7/30/2021 at 8:49 AM, JorgeB said: The quoted syslog mentions that the problem is the fiber module you're using in that port, it's not supported by the NIC. After some research got into this and it's possible to enable unsupported transceivers in Intel X520 - https://rymnd.org/blog/2020/unsupported-sfp-intel-x520/ Quote Link to comment
Beardmann Posted September 28, 2022 Share Posted September 28, 2022 Hi there I also have an X520 dual NIC in my server. I have only one port connected and I am able to see just one of the two 10G ports... I was wondering if this is by design? So if nothing is connected to the NIC port, the driver is just not loaded? Because... then why is this not the case with the internal 1G NICs in my server? Here I have one connected and another one which is not, yet both are identified as "eth0+1"... A bit strange to me lspci shows: 04:00.0 Ethernet controller: Intel Corporation Ethernet 10G 2P X520 Adapter (rev 01) 04:00.1 Ethernet controller: Intel Corporation Ethernet 10G 2P X520 Adapter (rev 01) and 07:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection (rev 03) 08:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection (rev 03) But I only have three devices eth0, eth1 (1G) and eth2 (10G)... but no eth3 /B Quote Link to comment
SimonF Posted September 28, 2022 Share Posted September 28, 2022 If you dont have an SFP installed it wont show as ethX Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.