Is it for the bin?


Recommended Posts

Hi,

I recently moved 2.4TB of files off a 3TB drive, then ran pre clear ready to add it to my array.  Pre clear through up a few issues  that I have never had before and then I ran an extended test.  Here are the results, please advise is this savable or should it be binned?

 

================================================================== 1.20
=                unRAID server Pre-Clear disk /dev/sde
=               cycle 1 of 1, partition start on sector 64
=
= Step 1 of 10 - Copying zeros to first 2048k bytes             DONE
= Step 2 of 10 - Copying zeros to remainder of disk to clear it DONE
= Step 3 of 10 - Disk is now cleared from MBR onward.           DONE
= Step 4 of 10 - Clearing MBR bytes for partition 2,3 & 4       DONE
= Step 5 of 10 - Clearing MBR code area                         DONE
= Step 6 of 10 - Setting MBR signature bytes                    DONE
= Step 7 of 10 - Setting partition 1 to precleared state        DONE
= Step 8 of 10 - Notifying kernel we changed the partitioning   DONE
= Step 9 of 10 - Creating the /dev/disk/by* entries             DONE
= Step 10 of 10 - Verifying if the MBR is cleared.              DONE
= Disk Post-Clear-Read completed                                DONE
Disk Temperature: 36C, Elapsed Time:  16:06:59
========================================================================1.20
== WDCWD30EFRX-68EUZN0   WD-WCC4N2REK1X7
== Disk /dev/sde has been successfully precleared
== with a starting sector of 64
============================================================================
** Changed attributes in files: /tmp/smart_start_sde  /tmp/smart_finish_sde
                ATTRIBUTE   NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS      RAW_VALUE
      Temperature_Celsius =   114     116            0        ok          36
 No SMART attributes are FAILING_NOW

 0 sectors were pending re-allocation before the start of the preclear.
 0 sectors were pending re-allocation after zero of disk in cycle 1 of 1.
 60 sectors are pending re-allocation at the end of the preclear,
    a change of 60 in the number of sectors pending re-allocation.
 0 sectors had been re-allocated before the start of the preclear.
 0 sectors are re-allocated at the end of the preclear,
    the number of sectors re-allocated did not change.

 

 

smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.10.28-Unraid] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Red
Device Model:     WDC WD30EFRX-68EUZN0
Serial Number:    WD-WCC4N2REK1X7
LU WWN Device Id: 5 0014ee 26258e985
Firmware Version: 82.00A82
User Capacity:    3,000,592,982,016 bytes [3.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Mon Oct 18 08:41:45 2021 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Disabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      ( 113)	The previous self-test completed having
					the read element of the test failed.
Total time to complete Offline 
data collection: 		(38940) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 391) minutes.
Conveyance self-test routine
recommended polling time: 	 (   5) minutes.
SCT capabilities: 	       (0x703d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR-K   200   200   051    -    1179
  3 Spin_Up_Time            POS--K   188   178   021    -    5600
  4 Start_Stop_Count        -O--CK   099   099   000    -    1519
  5 Reallocated_Sector_Ct   PO--CK   200   200   140    -    0
  7 Seek_Error_Rate         -OSR-K   200   200   000    -    0
  9 Power_On_Hours          -O--CK   072   072   000    -    20841
 10 Spin_Retry_Count        -O--CK   100   100   000    -    0
 11 Calibration_Retry_Count -O--CK   100   253   000    -    0
 12 Power_Cycle_Count       -O--CK   100   100   000    -    30
192 Power-Off_Retract_Count -O--CK   200   200   000    -    6
193 Load_Cycle_Count        -O--CK   197   197   000    -    9323
194 Temperature_Celsius     -O---K   115   110   000    -    35
196 Reallocated_Event_Count -O--CK   200   200   000    -    0
197 Current_Pending_Sector  -O--CK   200   200   000    -    60
198 Offline_Uncorrectable   ----CK   100   253   000    -    0
199 UDMA_CRC_Error_Count    -O--CK   200   200   000    -    0
200 Multi_Zone_Error_Rate   ---R--   200   200   000    -    11
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      5  Comprehensive SMART error log
0x03       GPL     R/O      6  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x21       GPL     R/O      1  Write stream error log
0x22       GPL     R/O      1  Read stream error log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa0-0xa7  GPL,SL  VS      16  Device vendor specific log
0xa8-0xb7  GPL,SL  VS       1  Device vendor specific log
0xbd       GPL,SL  VS       1  Device vendor specific log
0xc0       GPL,SL  VS       1  Device vendor specific log
0xc1       GPL     VS      93  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 167 (device log contains only the most recent 24 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 167 [22] occurred at disk power-on lifetime: 20833 hours (868 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 53 de 2c a0 40 00  Error: UNC at LBA = 0x153de2ca0 = 5702036640

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 18 00 01 53 de 2c a0 40 08  5d+22:02:27.635  READ FPDMA QUEUED
  60 00 08 00 10 00 01 53 de 2c 98 40 08  5d+22:02:27.513  READ FPDMA QUEUED
  60 00 08 00 c8 00 01 53 de 2c 90 40 08  5d+22:02:27.480  READ FPDMA QUEUED
  60 00 08 00 c0 00 01 53 de 2c 88 40 08  5d+22:02:26.769  READ FPDMA QUEUED
  60 00 08 00 b8 00 01 53 de 2c 80 40 08  5d+22:02:26.758  READ FPDMA QUEUED

Error 166 [21] occurred at disk power-on lifetime: 20833 hours (868 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 53 de 2e 98 40 00  Error: UNC at LBA = 0x153de2e98 = 5702037144

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 02 68 00 38 00 01 53 de 2e 88 40 08  5d+22:02:10.062  READ FPDMA QUEUED
  60 05 40 00 30 00 01 56 db 7f 70 40 08  5d+22:02:10.062  READ FPDMA QUEUED
  60 04 c0 00 28 00 01 56 db 84 b0 40 08  5d+22:02:10.062  READ FPDMA QUEUED
  60 05 40 00 20 00 01 56 db 89 70 40 08  5d+22:02:10.062  READ FPDMA QUEUED
  60 04 c0 00 18 00 01 56 db 8e b0 40 08  5d+22:02:10.062  READ FPDMA QUEUED

Error 165 [20] occurred at disk power-on lifetime: 20833 hours (868 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 53 de 2c 58 40 00  Error: UNC at LBA = 0x153de2c58 = 5702036568

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 04 c0 00 88 00 01 56 db 84 b0 40 08  5d+22:02:03.050  READ FPDMA QUEUED
  60 05 40 00 80 00 01 56 db 7f 70 40 08  5d+22:02:03.050  READ FPDMA QUEUED
  60 04 c0 00 78 00 01 56 db 7a b0 40 08  5d+22:02:03.043  READ FPDMA QUEUED
  60 05 40 00 70 00 01 56 db 75 70 40 08  5d+22:02:03.043  READ FPDMA QUEUED
  60 04 c0 00 68 00 01 56 db 70 b0 40 08  5d+22:02:03.043  READ FPDMA QUEUED

Error 164 [19] occurred at disk power-on lifetime: 20833 hours (868 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 55 cc 42 78 40 00  Error: UNC at LBA = 0x155cc4278 = 5734417016

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 a8 00 01 55 cc 42 78 40 08  5d+21:59:45.937  READ FPDMA QUEUED
  ef 00 10 00 02 00 00 00 00 00 00 a0 08  5d+21:59:45.919  SET FEATURES [Enable SATA feature]
  27 00 00 00 00 00 00 00 00 00 00 e0 08  5d+21:59:45.919  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 00 00 00 00 00 a0 08  5d+21:59:45.918  IDENTIFY DEVICE
  ef 00 03 00 46 00 00 00 00 00 00 a0 08  5d+21:59:45.918  SET FEATURES [Set transfer mode]

Error 163 [18] occurred at disk power-on lifetime: 20833 hours (868 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 55 cc 42 78 40 00  Error: UNC at LBA = 0x155cc4278 = 5734417016

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 80 00 01 55 cc 42 78 40 08  5d+21:59:42.391  READ FPDMA QUEUED
  60 00 08 00 78 00 01 55 cc 42 70 40 08  5d+21:59:42.358  READ FPDMA QUEUED
  60 00 08 00 70 00 01 55 cc 42 68 40 08  5d+21:59:42.280  READ FPDMA QUEUED
  60 00 08 00 68 00 01 55 cc 42 60 40 08  5d+21:59:42.247  READ FPDMA QUEUED
  60 00 08 00 60 00 01 55 cc 42 58 40 08  5d+21:59:42.247  READ FPDMA QUEUED

Error 162 [17] occurred at disk power-on lifetime: 20833 hours (868 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 55 cc 42 78 40 00  Error: UNC at LBA = 0x155cc4278 = 5734417016

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 0a 00 00 d8 00 01 55 cc 40 f8 40 08  5d+21:59:35.231  READ FPDMA QUEUED
  60 0a 00 00 d0 00 01 55 cc 36 f8 40 08  5d+21:59:35.171  READ FPDMA QUEUED
  60 0a 00 00 c8 00 01 55 cc 2c f8 40 08  5d+21:59:33.578  READ FPDMA QUEUED
  60 0a 00 00 b8 00 01 55 cc 22 f8 40 08  5d+21:59:33.518  READ FPDMA QUEUED
  60 06 c0 00 b0 00 01 55 cc 1c 38 40 08  5d+21:59:27.591  READ FPDMA QUEUED

Error 161 [16] occurred at disk power-on lifetime: 20833 hours (868 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 55 b5 be 08 40 00  Error: UNC at LBA = 0x155b5be08 = 5732941320

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 08 00 01 55 b5 be 08 40 08  5d+21:58:47.025  READ FPDMA QUEUED
  60 00 08 00 00 00 01 55 b5 be 00 40 08  5d+21:58:46.914  READ FPDMA QUEUED
  60 00 08 00 f8 00 01 55 b5 bd f8 40 08  5d+21:58:46.814  READ FPDMA QUEUED
  60 00 08 00 b8 00 01 55 b5 bd f0 40 08  5d+21:58:46.770  READ FPDMA QUEUED
  60 00 08 00 b0 00 01 55 b5 bd e8 40 08  5d+21:58:46.725  READ FPDMA QUEUED

Error 160 [15] occurred at disk power-on lifetime: 20833 hours (868 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 55 b5 be 08 40 00  Error: UNC at LBA = 0x155b5be08 = 5732941320

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 06 20 00 00 00 01 55 b5 bf 50 40 08  5d+21:58:39.499  READ FPDMA QUEUED
  60 03 10 00 f0 00 01 55 b5 bc 40 40 08  5d+21:58:39.498  READ FPDMA QUEUED
  60 01 88 00 e8 00 01 55 b5 ba b8 40 08  5d+21:58:39.480  READ FPDMA QUEUED
  60 0a 00 00 e0 00 01 55 b5 b0 b8 40 08  5d+21:58:39.464  READ FPDMA QUEUED
  60 0a 00 00 d8 00 01 55 b5 a6 b8 40 08  5d+21:58:39.447  READ FPDMA QUEUED

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed: read failure       10%     20841         5701892488
# 2  Short offline       Completed without error       00%     20552         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       258 (0x0102)
Device State:                        Active (0)
Current Temperature:                    35 Celsius
Power Cycle Min/Max Temperature:     29/38 Celsius
Lifetime    Min/Max Temperature:     13/40 Celsius
Under/Over Temperature Limit Count:   0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/60 Celsius
Min/Max Temperature Limit:           -41/85 Celsius
Temperature History Size (Index):    478 (41)

Index    Estimated Time   Temperature Celsius
  42    2021-10-18 00:44    33  **************
 ...    ..(  8 skipped).    ..  **************
  51    2021-10-18 00:53    33  **************
  52    2021-10-18 00:54    34  ***************
 ...    ..(  2 skipped).    ..  ***************
  55    2021-10-18 00:57    34  ***************
  56    2021-10-18 00:58    35  ****************
 ...    ..(  6 skipped).    ..  ****************
  63    2021-10-18 01:05    35  ****************
  64    2021-10-18 01:06    36  *****************
 ...    ..(277 skipped).    ..  *****************
 342    2021-10-18 05:44    36  *****************
 343    2021-10-18 05:45    37  ******************
 ...    ..(106 skipped).    ..  ******************
 450    2021-10-18 07:32    37  ******************
 451    2021-10-18 07:33    36  *****************
 ...    ..(  4 skipped).    ..  *****************
 456    2021-10-18 07:38    36  *****************
 457    2021-10-18 07:39    35  ****************
 458    2021-10-18 07:40    36  *****************
 ...    ..( 10 skipped).    ..  *****************
 469    2021-10-18 07:51    36  *****************
 470    2021-10-18 07:52    35  ****************
 ...    ..(  6 skipped).    ..  ****************
 477    2021-10-18 07:59    35  ****************
   0    2021-10-18 08:00    36  *****************
 ...    ..( 15 skipped).    ..  *****************
  16    2021-10-18 08:16    36  *****************
  17    2021-10-18 08:17    35  ****************
 ...    ..(  4 skipped).    ..  ****************
  22    2021-10-18 08:22    35  ****************
  23    2021-10-18 08:23    34  ***************
 ...    ..(  8 skipped).    ..  ***************
  32    2021-10-18 08:32    34  ***************
  33    2021-10-18 08:33    33  **************
 ...    ..(  7 skipped).    ..  **************
  41    2021-10-18 08:41    33  **************

SCT Error Recovery Control:
           Read:     70 (7.0 seconds)
          Write:     70 (7.0 seconds)

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2           11  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2           11  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x8000  4       538929  Vendor specific

 

Link to comment

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.