fir3drag0n Posted December 16, 2022 Share Posted December 16, 2022 (edited) Moin, bin neu hier und habe auch dieselbe Konfig, bis auf dass ich eine NVMe Drive habe und noch 2 HDDs (3,5") und 64 GB RAM. Leider auch alles versucht, mehr als C2 ist nicht möglich. Edited December 16, 2022 by fir3drag0n Quote Link to comment
mgutt Posted December 16, 2022 Share Posted December 16, 2022 1 hour ago, fir3drag0n said: dieselbe Konfig ? Hardware, was wie angeschlossen und bisherige Schritte genau benennen. Quote Link to comment
fir3drag0n Posted December 16, 2022 Share Posted December 16, 2022 (edited) Setup: - Gigabyte C246M-WU4 (Bios Version: F5) - Intel® Core™ i3-9100 CPU - 64 GB: 2x 32 GB (Micron MTA18ASF4G72AZ-3G2R) - 1x MEGA Electronics Fastro MS200 SSD, M.2 - 2x HDD 3,5" WD120EMFZ (über SATA 0 und SATA 1) - 2x NOCTUA NF-A12x25 PWM - PicoPSU (200W, über 160W Netzteil) Powertop gemäß Anleitung installiert, Autotune ausgeführt, Go File erstellt und Reboot gemacht. iGPU driver plugin installiert, CPU governor installiert, steht auf "powersave". Unraid USB link oben eingesteckt, Netzwerk über eth0. BIOS Einstellungen gemäß hier vorgenommen. Bin ratlos, was ich noch ändern könnte, die Packages gehen nicht über C2 hinaus. ASPM: lspci -vv | awk '/ASPM/{print $0}' RS= | grep --color -P '(^[a-z0-9:.]+|ASPM )' 00:1b.0 PCI bridge: Intel Corporation Cannon Lake PCH PCI Express Root Port #17 (rev f0) (prog-if 00 [Normal decode]) LnkCap: Port #17, Speed 8GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <4us LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes, Disabled- CommClk- 00:1b.4 PCI bridge: Intel Corporation Cannon Lake PCH PCI Express Root Port #21 (rev f0) (prog-if 00 [Normal decode]) LnkCap: Port #21, Speed 8GT/s, Width x4, ASPM L0s L1, Exit Latency L0s <1us, L1 <16us LnkCtl: ASPM L0s Enabled; RCB 64 bytes, Disabled- CommClk+ 00:1c.0 PCI bridge: Intel Corporation Cannon Lake PCH PCI Express Root Port #1 (rev f0) (prog-if 00 [Normal decode]) LnkCap: Port #1, Speed 8GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <4us LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes, Disabled- CommClk- 00:1c.5 PCI bridge: Intel Corporation Cannon Lake PCH PCI Express Root Port #6 (rev f0) (prog-if 00 [Normal decode]) LnkCap: Port #6, Speed 8GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <16us LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ 00:1d.0 PCI bridge: Intel Corporation Cannon Lake PCH PCI Express Root Port #9 (rev f0) (prog-if 00 [Normal decode]) LnkCap: Port #9, Speed 8GT/s, Width x4, ASPM L0s L1, Exit Latency L0s <1us, L1 <4us LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes, Disabled- CommClk- 02:00.0 Non-Volatile memory controller: Silicon Motion, Inc. SM2262/SM2262EN SSD Controller (rev 03) (prog-if 02 [NVM Express]) LnkCap: Port #0, Speed 8GT/s, Width x4, ASPM L0s, Exit Latency L0s <1us LnkCtl: ASPM L0s Enabled; RCB 64 bytes, Disabled- CommClk+ 04:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection (rev 03) LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <2us, L1 <16us LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ Powertop Tunables: >> Bad VM writeback timeout Good Enable SATA link power management for host1 Good Enable SATA link power management for host2 Good Enable SATA link power management for host3 Good Enable SATA link power management for host4 Good Enable SATA link power management for host5 Good Enable SATA link power management for host6 Good Enable SATA link power management for host7 Good Enable SATA link power management for host8 Good Runtime PM for I2C Adapter i2c-0 (SMBus I801 adapter at efa0) Good Runtime PM for I2C Adapter i2c-1 (i915 gmbus dpb) Good Autosuspend for USB device Mass Storage Device [JetFlash] Good Autosuspend for USB device xHCI Host Controller [usb2] Good Runtime PM for I2C Adapter i2c-2 (i915 gmbus dpc) Good Runtime PM for I2C Adapter i2c-3 (i915 gmbus misc) Good Runtime PM for I2C Adapter i2c-4 (i915 gmbus dpd) Good Autosuspend for USB device xHCI Host Controller [usb1] Good Runtime PM for PCI Device Intel Corporation Cannon Lake PCH PCI Express Root Port #6 Good Runtime PM for PCI Device Silicon Motion, Inc. SM2262/SM2262EN SSD Controller Good Runtime PM for PCI Device Intel Corporation Cannon Lake PCH PCI Express Root Port #21 Good Runtime PM for PCI Device Intel Corporation Cannon Lake PCH Thermal Controller Good Runtime PM for PCI Device Intel Corporation Cannon Point-LP LPC Controller Good Runtime PM for PCI Device Intel Corporation Cannon Lake PCH PCI Express Root Port #1 Good Runtime PM for disk sdc Good Runtime PM for port ata1 of PCI device: Intel Corporation Cannon Lake PCH SATA AHCI Controller Good Runtime PM for disk sda Good Runtime PM for port ata7 of PCI device: Intel Corporation Cannon Lake PCH SATA AHCI Controller Good Runtime PM for port ata8 of PCI device: Intel Corporation Cannon Lake PCH SATA AHCI Controller Good Runtime PM for port ata5 of PCI device: Intel Corporation Cannon Lake PCH SATA AHCI Controller Good Runtime PM for port ata6 of PCI device: Intel Corporation Cannon Lake PCH SATA AHCI Controller Good Runtime PM for port ata2 of PCI device: Intel Corporation Cannon Lake PCH SATA AHCI Controller Good Runtime PM for port ata3 of PCI device: Intel Corporation Cannon Lake PCH SATA AHCI Controller Good Runtime PM for port ata4 of PCI device: Intel Corporation Cannon Lake PCH SATA AHCI Controller Good Runtime PM for PCI Device Intel Corporation Cannon Lake PCH HECI Controller Good Runtime PM for PCI Device Intel Corporation Cannon Lake PCH SPI Controller Good Runtime PM for PCI Device Intel Corporation Cannon Lake PCH PCI Express Root Port #17 Good Runtime PM for PCI Device Intel Corporation 8th Gen Core 4-core Desktop Processor Host Bridge/DRAM Registers [Coffee Lake S] Good Runtime PM for PCI Device Intel Corporation Cannon Lake PCH Active Management Technology - SOL Good Runtime PM for PCI Device Intel Corporation Cannon Lake PCH PCI Express Root Port #9 Good Runtime PM for PCI Device Intel Corporation Cannon Lake PCH Shared SRAM Good Runtime PM for PCI Device Intel Corporation Ethernet Connection (7) I219-LM Good Runtime PM for PCI Device Intel Corporation I210 Gigabit Network Connection Good Runtime PM for PCI Device Intel Corporation CoffeeLake-S GT2 [UHD Graphics 630] Good Runtime PM for PCI Device Intel Corporation Cannon Lake PCH USB 3.1 xHCI Host Controller Good Runtime PM for PCI Device Intel Corporation Cannon Lake PCH SMBus Controller Good Runtime PM for PCI Device Intel Corporation Cannon Lake PCH SATA AHCI Controller >> Good Runtime PM for disk sdb Powertop Autotune Output: powertop powertop: /lib64/libncursesw.so.6: no version information available (required by powertop) powertop: /lib64/libtinfo.so.6: no version information available (required by powertop) modprobe cpufreq_stats failed Cannot load from file /var/cache/powertop/saved_results.powertop Cannot load from file /var/cache/powertop/saved_parameters.powertop File will be loaded after taking minimum number of measurement(s) with battery only RAPL device for cpu 0 RAPL device for cpu 0 Devfreq not enabled glob returned GLOB_ABORTED Cannot load from file /var/cache/powertop/saved_parameters.powertop File will be loaded after taking minimum number of measurement(s) with battery only Edited December 16, 2022 by fir3drag0n Quote Link to comment
fir3drag0n Posted December 16, 2022 Share Posted December 16, 2022 (edited) habe jetzt auch VM in Unraid deaktiviert, keine Änderung 😞 Habe noch einen PiKVM (https://wiki.geekworm.com/PiKVM-A3) mit so einer Karte (https://wiki.geekworm.com/PiKVM-A3#/media/File:X630-A5-IMG-4210-2.jpg) installiert. Anschluss nur an die ATX Pfostenleiste - kann es daran liegen? Edited December 16, 2022 by fir3drag0n Quote Link to comment
mgutt Posted December 17, 2022 Share Posted December 17, 2022 11 hours ago, fir3drag0n said: BIOS Einstellungen gemäß hier vorgenommen. BIOS resetten, bei den Powereinstellungen CEC2019 aktivieren und fertig. Das W480M hat diese Einstellung nicht. Quote Link to comment
mgutt Posted December 17, 2022 Share Posted December 17, 2022 10 hours ago, fir3drag0n said: habe jetzt auch VM in Unraid deaktiviert, Das kann das durchaus beeinflussen 10 hours ago, fir3drag0n said: installiert. Anschluss nur an die ATX Pfostenleiste - kann es daran liegen? Nein Quote Link to comment
fir3drag0n Posted December 17, 2022 Share Posted December 17, 2022 (edited) CEC2019 ist schon aktiviert. Gibt es hier Einstellungen, die das ändern? Kann es an der NVMe SSD liegen? Gibt es hier Empfehlungen? Edited December 17, 2022 by fir3drag0n Quote Link to comment
Bengon Posted December 17, 2022 Share Posted December 17, 2022 Versuch das mal " powertop --calibrate " (ohne "). Das hat meine C-States von 2 auf 7 gebracht. Soll angeblich nur die Anzeige kalibrieren-konfigurieren. Vielleicht ist es bei dir ja so. Bei mir geht aber auch der Stromverbrauch ein wenig runter. Versuchen kostet ja nichts. Quote Link to comment
mgutt Posted December 17, 2022 Share Posted December 17, 2022 1 hour ago, Bengon said: 1 hour ago, Bengon said: Soll angeblich nur die Anzeige kalibrieren So ist das auch. Du ziehst falsche Schlussfolgerungen. Dir ist auch hoffentlich klar, dass das bei jedem Reboot verfällt. Solltest du also jemals danach neu gestartet haben, ist es eh nicht mehr aktiv. Oder hast du calibrate in der Go File stehen? 5 hours ago, fir3drag0n said: CEC2019 ist schon aktiviert. Gibt es hier Einstellungen, die das ändern? Naja du kannst sie wieder überschreiben, wenn du sonst irgendwas änderst. Daher BIOS reset und wirklich nur das aktivieren. Quote Link to comment
Bengon Posted December 17, 2022 Share Posted December 17, 2022 Ich weiß das es nach jedem reboot wieder neu gestartet werden muss, und ich ziehe auch keine falschen Schlussfolgerungen. Denn wenn ich einen Screenshot nach dem Neustart von Powertop mache und dann das Calibrate Script starte dann sehe ich sehr wohl Änderungen bei Powertop wenn ich die Screenshots vergleiche.Habe es noch mal getestet. Sofort habe ich bessere C-States ohne eine Änderung im Bios etc. vorgenommen zu haben Quote Link to comment
Bengon Posted December 17, 2022 Share Posted December 17, 2022 (edited) 3 minutes ago, Bengon said: Ich weiß das es nach jedem reboot wieder neu gestartet werden muss, und ich ziehe auch keine falschen Schlussfolgerungen. Denn wenn ich einen Screenshot nach dem Neustart von Powertop mache und dann das Calibrate Script starte dann sehe ich sehr wohl Änderungen bei Powertop wenn ich die Screenshots vergleiche.Habe es noch mal getestet. Sofort habe ich bessere C-States ohne eine Änderung im Bios etc. vorgenommen zu haben Dieses mal sogar bis C9 Edited December 17, 2022 by Bengon Quote Link to comment
mgutt Posted December 17, 2022 Share Posted December 17, 2022 Ich nehme alles zurück. Tatsächlich macht calibrate Sachen, wie zb alle USB Devices auf Auto und alle SCSI Devices auf min_power zu stellen: https://github.com/fenrus75/powertop/blob/2b359152c5875b30f29d0ffdec723ce4624d1323/src/calibrate/calibrate.cpp#L374 Im Vergleich dazu macht das auto-tune selektiver, setzt das also nicht bei allen Devices. Aber den Sinn habe ich auch noch nicht verstanden. Mit den Kommandos aus dem Powertop Thread sollte man jedendfalls alles abdecken was auch auto-tune und calibrate macht. Powertop braucht man also nicht dafür. Quote Link to comment
fir3drag0n Posted December 18, 2022 Share Posted December 18, 2022 Also " powertop --calibrate " hat schonmal nichts geändert, verharrt bei C2. Ich werde jetzt nochmal verschiedene USB Ports probieren und BIOS resetten und nur CEC2019 aktivieren. Quote Link to comment
fir3drag0n Posted December 19, 2022 Share Posted December 19, 2022 So, ich habe Mal etwas Fehlerbehebung betrieben und es ist die NVMe SSD, die mehr als C2 verhindert. Ausgebaut und sofort ging C8. Meine Fragen: 1. Welche M2 SSDs empfehlt ihr, die keine Probleme mit powertop machen? 2. Spielt der M2 Slot eine Rolle (ist derzeit oben in M2A eingesteckt)? 3. Wie erreiche ich C9 und C10 Package? Quote Link to comment
jj1987 Posted December 19, 2022 Share Posted December 19, 2022 3 hours ago, fir3drag0n said: Welche M2 SSDs empfehlt ihr, die keine Probleme mit powertop machen? Samsung ist in der Hinsicht (positiv) unauffällig. Mit einer 970 EVO Plus macht man auch definitiv nichts verkehrt. Falls der Preisunterschied gering ist, kann man auch direkt auf eine 980 Pro gehen Quote Link to comment
mgutt Posted December 19, 2022 Share Posted December 19, 2022 On 12/16/2022 at 10:05 PM, fir3drag0n said: - 1x MEGA Electronics Fastro MS200 SSD, M.2 Also die? Dann vermute ich, dass die in einer Liste vom Linux Kernel steht, damit die niemals in den Standby wechselt. Es gibt da nämlich eine wo auch die Kingston A2000 gelandet ist: https://www.heise.de/hintergrund/c-t-wirkt-Problematische-SSD-im-Bauvorschlag-fuehrt-zu-Bugfix-im-Linux-Kernel-5074713.html Ich kann auch problemlos die Samsung Pro und Evo Plus empfehlen. Auch SanDisk / WD hatte ich schon einige ohne Probleme bei den C-States. Quote Link to comment
fir3drag0n Posted December 19, 2022 Share Posted December 19, 2022 31 minutes ago, mgutt said: Also die? Dann vermute ich, dass die in einer Liste vom Linux Kernel steht, damit die niemals in den Standby wechselt. Es gibt da nämlich eine wo auch die Kingston A2000 gelandet ist: https://www.heise.de/hintergrund/c-t-wirkt-Problematische-SSD-im-Bauvorschlag-fuehrt-zu-Bugfix-im-Linux-Kernel-5074713.html Ich kann auch problemlos die Samsung Pro und Evo Plus empfehlen. Auch SanDisk / WD hatte ich schon einige ohne Probleme bei den C-States. Korrekt, ansonsten ist die sonst auch sehr preiswert und immer mal im Angebot. Ansonsten wandert sie in den Desktop und ich gucke mal, ob ich noch eine Samsung organisieren kann. Quote Link to comment
fir3drag0n Posted December 19, 2022 Share Posted December 19, 2022 2 hours ago, mgutt said: Also die? Dann vermute ich, dass die in einer Liste vom Linux Kernel steht, damit die niemals in den Standby wechselt. Es gibt da nämlich eine wo auch die Kingston A2000 gelandet ist: https://www.heise.de/hintergrund/c-t-wirkt-Problematische-SSD-im-Bauvorschlag-fuehrt-zu-Bugfix-im-Linux-Kernel-5074713.html Ich kann auch problemlos die Samsung Pro und Evo Plus empfehlen. Auch SanDisk / WD hatte ich schon einige ohne Probleme bei den C-States. Korrekt, ansonsten ist die sonst auch sehr preiswert und immer mal im Angebot. Ansonsten wandert sie in den Desktop und ich gucke mal, ob ich noch eine Samsung organisieren kann. Wie kommt man denn in C9/C10, HDMI und USB abstecken? Quote Link to comment
Bengon Posted December 19, 2022 Share Posted December 19, 2022 Diese habe ich verbaut,sind auch öfters im Angebot : 2x Crucial P5 500GB Quote Link to comment
Bengon Posted December 19, 2022 Share Posted December 19, 2022 6 minutes ago, fir3drag0n said: Korrekt, ansonsten ist die sonst auch sehr preiswert und immer mal im Angebot. Ansonsten wandert sie in den Desktop und ich gucke mal, ob ich noch eine Samsung organisieren kann. Wie kommt man denn in C9/C10, HDMI und USB abstecken? Ich habe kein USB Gerät (ausser Unraid Stick) und auch kein HDMI angeschlossen Quote Link to comment
fir3drag0n Posted December 19, 2022 Share Posted December 19, 2022 55 minutes ago, Bengon said: Ich habe kein USB Gerät (ausser Unraid Stick) und auch kein HDMI angeschlossen Und du erreichst damit C9/C10? Quote Link to comment
Bengon Posted December 19, 2022 Share Posted December 19, 2022 2 hours ago, fir3drag0n said: Und du erreichst damit C9/C10? C9 ja ,aber nicht zu 100 % .Das schwankt auch immer Quote Link to comment
fir3drag0n Posted December 22, 2022 Share Posted December 22, 2022 (edited) So, habe nun eine Samsung 970 Evo Plus verbaut und komme nun bis C10. Angeschlossen sind derzeit 3x Noctua Lüfter, einer davon für die CPU. Angeschlossen aber nur LAN und unRAID USB-Stick. Mit den beiden HDDs im Spindown messe ich im idle um die 10W. VM aus, Docker an. Edited December 22, 2022 by fir3drag0n Quote Link to comment
mgutt Posted December 22, 2022 Share Posted December 22, 2022 7 hours ago, fir3drag0n said: Mit den beiden HDDs im Spindown messe ich im idle um die 10W. VM aus, Docker an Klingt gut. Was hattest du eigentlich vorher? Quote Link to comment
fir3drag0n Posted December 22, 2022 Share Posted December 22, 2022 (edited) Perspektivisch die alte Synology und einen RPi 4 auf einem Gerät* (unRAID, stromsparend) vereinen. Arbeite mich gerade in unRAID ein und werde sicherlich noch die eine oder andere Frage hier stellen Was ich benötige: Pihole Unbound Plex Nextcloud Bitwardenrs Wireguard Tvheadend mit telerising / easyepg Iobroker Raspberrymatic 😉 Edited December 22, 2022 by fir3drag0n Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.