April 21, 20224 yr 6 minutes ago, always67 said: forgive my ignorance.Too many people pay attention to the 12th generation,I can't find information about the 11th generation. And Jasperlake's GPU is actually same as Comet Lake No, that‘s not entirely true, you have a low power chip where it is something entirely different where GUC and HUC needs to be enabled for the iGPU to fully work.
April 21, 20224 yr 9 minutes ago, ich777 said: No, that‘s not entirely true, you have a low power chip where it is something entirely different where GUC and HUC needs to be enabled for the iGPU to fully work. This is the most important place, on 6.9.2 I can enable GUC and HUC by adding ‘i915.force_probe=4e71 i915.enable_guc=2’ in /boot/config/modprobe.d/i915.cfg however all methods fail on 6.10
April 21, 20224 yr 1 hour ago, always67 said: This is the most important place, on 6.9.2 I can enable GUC and HUC by adding ‘i915.force_probe=4e71 i915.enable_guc=2’ in /boot/config/modprobe.d/i915.cfg however all methods fail on 6.10 I have to look into it if I can get a board like yours and test it myself why it fails. Have to look into it what they cost over here.
April 21, 20224 yr 46 minutes ago, ich777 said: I have to look into it if I can get a board like yours and test it myself why it fails. Have to look into it what they cost over here. Thank you so much, waiting for your good news
April 24, 20224 yr On 4/21/2022 at 11:56 PM, ich777 said: I have to look into it if I can get a board like yours and test it myself why it fails. Have to look into it what they cost over here. 'The kernel parameter i915.enable_guc=2 must be added to the Linux hw decode of all Jasper Lake processors, because the VME of this processor has been castrated and can only do EncSliceLP encoding in VAAPI. If you don't add it, you can't do rate control. In addition, linux-firmware must not be missing.Several of QNAP's new cameras are crippled because of lack of firmware.' I found this passage on the forum, is the linux firmware for unraid 6.10 rc missing?
April 24, 20224 yr 1 hour ago, always67 said: I found this passage on the forum, is the linux firmware for unraid 6.10 rc missing? No, it exists.
April 27, 20224 yr On 4/24/2022 at 4:34 PM, ich777 said: No, it exists. I found the reason，but no solution https://gitlab.freedesktop.org/drm/intel/-/issues/4067
April 27, 20224 yr 2 minutes ago, always67 said: I found the reason，but no solution https://gitlab.freedesktop.org/drm/intel/-/issues/4067 Are you already on RC5 and have tried if it is fixed? I think you have to wait a little longer until 6.11 RC series is released which will include a newer Kernel.
April 27, 20224 yr 10 hours ago, ich777 said: Are you already on RC5 and have tried if it is fixed? I think you have to wait a little longer until 6.11 RC series is released which will include a newer Kernel. Nothing changes. It seems 6.11 RC is the only way
April 28, 20224 yr I've got an N6005 coming for use as a pfsense box, but was planning on testing some other use cases also... happy to help with testing to get hw acceleration working when/if it arrives
May 2, 20224 yr On 4/28/2022 at 5:09 AM, tjb_altf4 said: I've got an N6005 coming for use as a pfsense box, but was planning on testing some other use cases also... happy to help with testing to get hw acceleration working when/if it arrives When it arrives and you are testing it please let me know if it's the same as for @always67, we already have a workaround for this on 6.10.0-rc5
May 3, 20224 yr 14 hours ago, ich777 said: When it arrives and you are testing it please let me know if it's the same as for @always67, we already have a workaround for this on 6.10.0-rc5 It'll be a few weeks off yet, shipping has been delayed again due to lockdowns over in China, so won't arrive before stable releases (or will it? 🤣)
May 3, 20224 yr On 4/7/2022 at 1:57 PM, ontheroad said: Hello, Evey one, What is the Linux kernel version of UNRAID? Can GUC/NUC be enabled?Thank you for your help https://jellyfin.org/docs/general/administration/hardware-acceleration.html#intel-gen9-and-gen11-igpus https://github.com/intel/media-driver#known-issues-and-limitations yes，it work！
May 23, 20224 yr On 5/2/2022 at 7:34 PM, ich777 said: When it arrives and you are testing it please let me know if it's the same as for @always67, we already have a workaround for this on 6.10.0-rc5 Arrived today, testing tonight
May 23, 20224 yr 2 minutes ago, tjb_altf4 said: Arrived today, testing tonight With the patch applied since 6.10.0rc8 everything should work fine.
May 23, 20224 yr 2 hours ago, ich777 said: With the patch applied since 6.10.0rc8 everything should work fine. Having a bit of trouble, might have missed something, have gone through the following steps: install intel_gpu_top plugin echo "blacklist i915" > /boot/config/modprobe.d/i915.conf reboot connected hdmi reboot i915.enable_guc=3 reboot I can see transcoding kick in for a second in intel_gpu_top (identifies cpu/gpu correctly), but them it falls back to cpu transcoding. Running on Unraid 6.10.1 Edited May 23, 20224 yr by tjb_altf4
May 23, 20224 yr 5 minutes ago, tjb_altf4 said: Having a bit of trouble, might have missed something, have gone through the following steps: install intel_gpu_top plugin echo "blacklist i915" > /boot/config/modprobe.d/i915.conf reboot connected hdmi reboot i915.enable_guc=3 reboot I can see transcoding kick in for a second in intel_gpu_top (identifies cpu/gpu correctly), but them it falls back to cpu transcoding. Running on Unraid 6.10.1 https://forums.unraid.net/topic/121267-11代cpu-n6005-610-rc3-docker硬解的正确打开方式？（解决了！！！）/
May 23, 20224 yr 8 minutes ago, tjb_altf4 said: I can see transcoding kick in for a second in intel_gpu_top (identifies cpu/gpu correctly), but them it falls back to cpu transcoding. Running on Unraid 6.10.1 Did you try it with Plex? Maybe also try it with Jellyfin. What is the output from: ls -la /dev/dri Can you upload your Diagnostics please? @always67 does it work on your machine?
May 23, 20224 yr Just now, ich777 said: Did you try it with Plex? Maybe also try it with Jellyfin. What is the output from: ls -la /dev/dri Can you upload your Diagnostics please? @always67 does it work on your machine? I tried it with your Jellyfin container, and Emby official (I have premiere) Both recognized and provided quicksync and vaapi options under transcoding options root@UNRAIDVM:~# ls -la /dev/dri total 0 drwxrwxrwx 3 root root 100 May 23 01:32 ./ drwxr-xr-x 15 root root 3280 May 23 01:33 ../ drwxrwxrwx 2 root root 80 May 23 01:32 by-path/ crwxrwxrwx 1 root video 226, 0 May 23 01:32 card0 crwxrwxrwx 1 root video 226, 128 May 23 01:32 renderD128 note: while the name is UNRAIDVM, it is running on baremetal video blips ~2% at start, then it reverts to cpu transcode unraidvm-diagnostics-20220523-1650.zip
May 23, 20224 yr 11 minutes ago, tjb_altf4 said: Both recognized and provided quicksync and vaapi options under transcoding options This is really strange, it looks like everything is working and initialized properly. Can you maybe also send over the transcoding log after starting a transcode?
May 23, 20224 yr 19 minutes ago, ich777 said: This is really strange, it looks like everything is working and initialized properly. Can you maybe also send over the transcoding log after starting a transcode? transcode logs added ffmpeg-transcode-18222f33-a0d3-4d3b-bc6e-1d810ebb868d_1.txt
May 23, 20224 yr 57 minutes ago, tjb_altf4 said: transcode logs added This is really strange since it probes against QuickSync and VAAPI and returns that it's successful, after it tries to transcode with VAAPI it fails and ultimately falls back to software encoding. @always67 what have you set in your transcoding settings in Emby?
May 23, 20224 yr might try and nuke my unraid install and have a clean start in 6.10, its only a test server/licence anyway so not too fussed
May 23, 20224 yr Up and running now Other than doing a nuke and pave, I was running GUI mode this time around too
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.