Vetteman Posted July 2, 2022 Share Posted July 2, 2022 I have a array of two parity drives (2 x WD Red Plus 6 TB) and data five data drives (2 x WD Red Plus 4 TB, 1 x WD Green 4 TB, 1 x Toshiba NAS 4 TB, 1 x WD Blue 5 TB). For 2 months now the WD Blue 5 TB has started to generate UDMA CRC errors. It is now up to 40. When the thumb turns orange I do acknowledge it and the thumb turns green. My scheduled monthly parity checks report everything is fine. I did do as suggested on this forum in other threads. I switched the sata cable with a brand new one. Errors returned. I then moved the sata cable from the motherboard's sata port to a port on my PCIE sata controller. Errors returned. I then removed the drive from a power connector on one of my sata power cables. And plug it into an empty power connector on a different power sata cable. Errors returned. I do have a brand new WD Red Plus 6 TB drive which has not been used yet. Before I swap the failing WD Blue 5 TB with the new WD Red Plus 6 TB is there anything else I could try? Since the WD Diag Tools are for Windows I can not run these from the Slackware OS. I did install the DiskSpeed docker and the failing drive's performance appears to be fine via DiskSpeed. Sorry to bring up a topic that appears to be thrashed to death, but I'd rather ask here then blindly proceed. I recently upgraded to Unraid 6.10.3 but these errors were being reported with 6.10.2 as well. Thank you for your time. Quote Link to comment
Vetteman Posted July 2, 2022 Author Share Posted July 2, 2022 PS: All my drives are new and it is Unraid who broke their virginity. Only the WD 5 TB had a previous life as an WD external USB3 drive which was used to backup my digital photos and 3D renderings. Quote Link to comment
Frank1940 Posted July 2, 2022 Share Posted July 2, 2022 1 hour ago, Vetteman said: Errors returned. First thing, CRC errors are not fatal errors. They are always corrected or the system comes to a halt with a read error. If there are a lot of CRC errors, the time to correct them can become an issue. (The data is reread from the disk and resent until it gets there correctly.) They are almost never caused by a problem with the hard disk! One of the problems is that the number of detected CRC errors is stored on the hard disk and that counter can not be reset. (In Unraid, we can knowledge the current count and Unraid will not notify us until the count increases.) Second thing. You say the errors returned. Does this mean that the count is actually increasing or that you 'noticed' that the disk was showing the errors. BTW, forty errors is not an excessive number. What period of time are we talking about here-- hours, days, weeks, months? One thing to make sure of is that you have not bundled your SATA data cables together in an effort to make things look 'neat'. Crosstalk between cables can cause CRC errors. You also mentioned that it was a WD drive. You might want to read this Support Article from Western Digital: https://support-en.wd.com/app/answers/detailweb/a_id/15954 You can also run the long SMART test from the Self-Test tab for that disk after clicking on that disk from the Main tab of the Unraid GUI. That will perform basically the same test of the WD Tools. Quote Link to comment
Vetteman Posted July 2, 2022 Author Share Posted July 2, 2022 Thanks kindly for the reply. When I said the errors returned, I mean the number of errors increased. What started out as 1 error is now 40. I did check for crossed cables and made sure the cable for the drive is not touching another sata cable. Presently running a SMART extended test on the drive. Again many thanks... Quote Link to comment
Vetteman Posted July 3, 2022 Author Share Posted July 3, 2022 The SMART extended test reports "completed without error". Tried different sata cables, different power connections, different sata ports (mobo, pcie controller), traced cable to ensure it is not crossed with another and it is not. Not sure if my internal sata cables are shielded or not. Too bad esata have a different sata connector as I have a few esata shielded cables I could use. So I am perplexed and very concerned why I am getting the UDMA CRC errors. Quote Link to comment
itimpi Posted July 3, 2022 Share Posted July 3, 2022 Just now, Vetteman said: So I am perplexed and very concerned why I am getting the UDMA CRC errors. Are you using locking SATA cables? I believe that with WD drives you are normally better off using non-locking cables. Quote Link to comment
Vetteman Posted July 3, 2022 Author Share Posted July 3, 2022 Using locking cables. Quote Link to comment
Frank1940 Posted July 3, 2022 Share Posted July 3, 2022 1 hour ago, Vetteman said: Using locking cables. Read that article that I posted the link to carefully. If the drive does not have the shroud molded into it, a metal locking connector will allow a 'floating' connection as the metal locking connectors seldom have the internal locking nibs. This floating connection is unreliable in maintaining a good connection as the drive will vibrate due to the rotation of the platters. (The SATA connector system is a poster child on how not to design any connector system!!!) You can test for this condition by gently pulling on the cable. With the non-locking cable, You should be able to feel some slight resistance as the cable disconnects. No resistance means a poor connection. With a locking connector, you should not be able to pull the connector out with any reasonable force. Quote Link to comment
Squid Posted July 3, 2022 Share Posted July 3, 2022 (Side Note: Any locking cabling that does not have the internal "bumps" violates the spec of the cable and should be avoided in the first place - FWIW, every single locking cable I've ever had that comes included with a motherboard is missing those bumps) Quote Link to comment
Vetteman Posted July 3, 2022 Author Share Posted July 3, 2022 I find the WD article very confusing. In this photo it does not show a photo of the sata cable but says the latching cable does not include the internal bumps but points to the WD hard drive connector and not a cable. Quote Link to comment
Vetteman Posted July 3, 2022 Author Share Posted July 3, 2022 In this photo it shows the WD hard drive SATA connectors that do not have the shroud and should not use the locking connectors but says for this type of connector "use the SATA cable receptables with internal bumps like the images above". Yet there are NO images above of the SATA cables. Quote Link to comment
Vetteman Posted July 3, 2022 Author Share Posted July 3, 2022 I know what the locking connectors are but confused by the two statements I've referenced. What am I missing? Many thanks. Quote Link to comment
Squid Posted July 3, 2022 Share Posted July 3, 2022 PhotoBucket has kindly placed a watermark across the pictures, but you can make it out. (or if you look at a non-locking cable, it will be quite easy to see the internal "bump" Quote Link to comment
Vetteman Posted July 3, 2022 Author Share Posted July 3, 2022 (edited) I have in my hands two SATA cables. A blue one with the metal latches and a red cable with black connectors that does not have the metal connectors. And other than the latches, they look identical. I see the differences between the SATA connectors on the hard drives for latching and non latching. The shroud is in plain sight. But with the cables, the only differences I can see are the latches. I've checked Amazon.ca and Newegg.ca for latches and unlatched sata cables and the only differences are the latches. I will check the connector on the WD Blues 5TB. Edited July 3, 2022 by Vetteman Quote Link to comment
Frank1940 Posted July 3, 2022 Share Posted July 3, 2022 The nibs are down inside the female connectors on the cable. They are the same color as the plastic of the connector housing. They are very small and quite hard to see unless you shine a light down inside of the connector. If there are the proper nibs on the cable, when you pull the cable off of the drive, you can feel a slight resistance until the connector releases. (The nibs are designed so that the cable has a slight interference fit when it is inserted into the plug on the drive. Because these parts are made with thermoplastic, the design can only allow a very minimum of interference before the design would have problems with cold flow of the thermoplastic.) It is generally accepted that ALL cables without the metal latch have the plastic nibs. Furthermore, it also accepted that any cable with the metal latches does NOT have the plastic nibs. The problem comes with those certain models of WD drives that do not have the shroud. ( The shroud is not a part of the SATA connector spec.) However, it is present on all other hard drives. I have grabbed a screenshot of that shroud and circled it. The metal tab of the latch type cable pushes against the shroud to force the mating connectors together (the nibs perform the same service). (The barbs on the latch also provide additional locking function to prevent the connector from working loose.) As you can visualize, with the shroud missing, there is no connector force as well as well as no locking function. There is another picture in the link of a WD drive without the shroud. It may look like the shroud is there but a careful inspection will show that the opening is much larger and the latch will not function properly. If you can pull a latching connector off the drive with little to no force, the drive does not have the shroud! Quote Link to comment
Vetteman Posted July 4, 2022 Author Share Posted July 4, 2022 I replaced the SATA cable with a non latching one and I am still getting udma crc errors. The count is now 44. And the cable is not crossing with any other SATA cables. Quote Link to comment
trurl Posted July 4, 2022 Share Posted July 4, 2022 Do all cables, power and SATA, have plenty of slack so the connectors can sit squarely on the connection with no tension that might make them move? Quote Link to comment
Vetteman Posted July 4, 2022 Author Share Posted July 4, 2022 All the cables look fine to me. And I do not have an issue with any other drives. Quote Link to comment
Frank1940 Posted July 4, 2022 Share Posted July 4, 2022 Looking over the thread, I think there is one more thing to try. Swap the drive end of the SATA cable (connected to the drive with the CRC errors) to another drive. Take the SATA cable from that drive and connect it to the drive with the CRC errors. Now let's see where the CRC errors occur. Quote Link to comment
Vetteman Posted July 4, 2022 Author Share Posted July 4, 2022 Good idea. Will try that. I did replace the cable on the failing drive with a new, never used before cable and the errors continued. However I will do what you suggested. Thanks kindly... Quote Link to comment
Vetteman Posted July 4, 2022 Author Share Posted July 4, 2022 (edited) Switched cables with another good hard drive. I will report back and many thanks to everyone's tips and info. Appreciate it alot. Edited July 4, 2022 by Vetteman Quote Link to comment
Vetteman Posted July 5, 2022 Author Share Posted July 5, 2022 I did as suggested and switched the SATA cable with a known good drive. The WD Blue 5 TB has generated another UDMA CRC error. Any other suggestions? Quote Link to comment
trurl Posted July 5, 2022 Share Posted July 5, 2022 Looks like we never asked for diagnostics. Quote Link to comment
Frank1940 Posted July 5, 2022 Share Posted July 5, 2022 (edited) You might actually have a most highly unusual situation. You have a hard drive that does generate CRC errors when transferring data. (It occurs so rarely and the cost to repair/test is so much greater than most of the other much more likely causes-- SATA cables and SATA controllers-- that we avoid even considering it until it is the last possible thing left...) Edited July 5, 2022 by Frank1940 Quote Link to comment
trurl Posted July 5, 2022 Share Posted July 5, 2022 17 minutes ago, Frank1940 said: the last possible thing left We don't know anything about any of the other possible things since we don't have diagnostics. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.