trurl Posted August 6, 2022 Share Posted August 6, 2022 Stop the read check then post another screenshot of Array Operation. Quote Link to comment
trurl Posted August 6, 2022 Share Posted August 6, 2022 4 minutes ago, trurl said: did you let parity2 rebuild finish? It would have taken many hours. Quote Link to comment
StewLoft Posted August 6, 2022 Author Share Posted August 6, 2022 4 minutes ago, trurl said: Stop the read check then post another screenshot of Array Operation. OK Quote Link to comment
trurl Posted August 6, 2022 Share Posted August 6, 2022 Your diagnostics and screenshots seem out-of-sync. Post a new screenshot of Main - Array Devices and new diagnostics. Quote Link to comment
trurl Posted August 6, 2022 Share Posted August 6, 2022 Also post a screenshot of Unassigned Devices Quote Link to comment
StewLoft Posted August 6, 2022 Author Share Posted August 6, 2022 tower-diagnostics-20220806-1318.zip Quote Link to comment
StewLoft Posted August 6, 2022 Author Share Posted August 6, 2022 Dev1 is a SSD used for the main OS of the computer. Dev2 was the original parity disc Quote Link to comment
trurl Posted August 6, 2022 Share Posted August 6, 2022 Your diagnostics shows original disk1 still attached, and its SMART report looks OK. Probably you disturbed connections when you were mucking about inside. I still would like you to confirm that you let parity2 rebuild finish and it took many hours. Quote Link to comment
StewLoft Posted August 6, 2022 Author Share Posted August 6, 2022 When I first removed disc1 (4TB HDD) it was showing in unassigned. Now it is not listed there...It is still connected via sata and power though. Quote Link to comment
StewLoft Posted August 6, 2022 Author Share Posted August 6, 2022 Yes, Parity2 was in for approximately 1 week and showed valid before I removed parity (6TB) from the assignment. Quote Link to comment
trurl Posted August 6, 2022 Share Posted August 6, 2022 I'll take a while to go through the syslog, it was already having connection problems with disk1 and disk9 when you booted 2 days ago. I'm going to eat some lunch first. Quote Link to comment
StewLoft Posted August 6, 2022 Author Share Posted August 6, 2022 OK, thank you very much for looking at this. I will do the same and check back in an hour. Quote Link to comment
trurl Posted August 6, 2022 Share Posted August 6, 2022 Disable Docker in Settings and leave it disabled until we get things fixed. Quote Link to comment
trurl Posted August 6, 2022 Share Posted August 6, 2022 Do you have backups of anything important and irreplaceable? Quote Link to comment
StewLoft Posted August 6, 2022 Author Share Posted August 6, 2022 Not for any of the media. Quote Link to comment
StewLoft Posted August 6, 2022 Author Share Posted August 6, 2022 docker disabled Quote Link to comment
StewLoft Posted August 6, 2022 Author Share Posted August 6, 2022 So, this is what is says now on Dashboard. Quote Link to comment
StewLoft Posted August 6, 2022 Author Share Posted August 6, 2022 But on Main it shows. Quote Link to comment
trurl Posted August 6, 2022 Share Posted August 6, 2022 I looked at SMART for disk9, those are just CRC errors. These are recorded by the disk when it receives inconsistent data (checksum), almost always connection problems. You can click on that 👎to acknowledge those and it will warn again if they increase. You have a couple of Marvell controllers. These are not recommended anymore but I don't think they are causing the problems. Disk1 wasn't connected to them anyway. Some corruption on emulated disk1 and on disk5, but both are mounted and show plenty of data. Not sure why it says parity isn't valid. Maybe it thinks you should replace/rebuild the 1st parity disk. We can worry about that later. The fact that missing disk1 is being emulated well enough to mount makes me think parity2 should be OK. If you click on the View icon at far right for disk1 (and for disk5) you should be able to drill down into its folders. Take a look and see if they look OK. Quote Link to comment
StewLoft Posted August 6, 2022 Author Share Posted August 6, 2022 Yes, both show the files listed. How do I know if the controllers are Marvell? I will look for alternatives. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.