Preclear und SMART Errors


Recommended Posts

Hallo,

 

bei einer Platte im Preclear bricht nachdem beim ersten Mal das Post Read failed war, failed es nun bereits beim Pre Read.

 

Interessanter Weiße war es die Platte die am Anfang gar keine SMART Error wie Current Pending Sectors oder RAW Read Errors hatte.

 

Screenshot_20220811-201648_Firefox.thumb.png.a640b2ae62c73de936b9ec57097651ef.png

 

Ich vermute damit ist die hin?

 

Vielen Dank!

 

Viele Grüße

 

Revan335

Link to comment
32 minutes ago, Revan335 said:

Ich vermute damit ist die hin?

 

Zieh erstmal ein Backup wichtiger Daten von der Disk. Dann boote mal neu und guck Dir die drei Werte (reallocated sector count, pending und event count) danach nochmals an. Nach dem Boot geht reallocated sector count wahrscheinlich hoch. Dann ist sie hin. Wenn sich an den Werten nichts ändert, dann gibt es evtl. keine Spares mehr. Das wäre auch schlecht.

 

Link to comment

Da nichts drauf ist, da ich noch in der Preclear Phase bin vor der Aufnahme ins Array, brauch ich kein Backup.

1 hour ago, hawihoney said:

 

Zieh erstmal ein Backup wichtiger Daten von der Disk. Dann boote mal neu und guck Dir die drei Werte (reallocated sector count, pending und event count) danach nochmals an. Nach dem Boot geht reallocated sector count wahrscheinlich hoch. Dann ist sie hin. Wenn sich an den Werten nichts ändert, dann gibt es evtl. keine Spares mehr. Das wäre auch schlecht.

 

Aber kann es mit nem Reboot mal probieren.

Link to comment

Ich denke die Platte ist hin, auch wenn sie noch nicht entschieden hat, was sie mit den Current Pending Sectors machen soll. Aber selbst wenn die diese aufgibt und stattdessen Ersatzsektoren verwendet. Wer weiß wie lange die dann noch lebt.

 

Vermutlich würde sie Platte die Entscheidung endgültig treffen, wenn du einen erweiterten SMART Test machst. Mach den mal bitte.

 

 

Link to comment
16 hours ago, mgutt said:

Ich denke die Platte ist hin, auch wenn sie noch nicht entschieden hat, was sie mit den Current Pending Sectors machen soll. Aber selbst wenn die diese aufgibt und stattdessen Ersatzsektoren verwendet. Wer weiß wie lange die dann noch lebt.

 

Vermutlich würde sie Platte die Entscheidung endgültig treffen, wenn du einen erweiterten SMART Test machst. Mach den mal bitte.

 

 

Schlägt kurz nachdem Start fehl.

Oder muss ich irgendwas dabei beachten?

Soll ich den Bericht mal Posten?

Link to comment
2 hours ago, mgutt said:

Da wird ja denke ich irgendein Fehler kommen oder nicht? Komische Platte ^^

Unbekannter Fehler.

Screenshot_20220812-193154_Firefox.thumb.png.4fea2f0b5adefe9e27cc65253d66a54b.png

smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.15.46-Unraid] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Red
Device Model:     WDC WD60EFRX-68MYMN1
Serial Number:    WDxxxxxx
LU WWN Device Id: 5 0014ee 260e9d9a7
Firmware Version: 82.00A82
User Capacity:    6,001,175,126,016 bytes [6.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5700 rpm
Device is:        In smartctl database 7.3/5387
ATA Version is:   ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Fri Aug 12 19:32:00 2022 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (  73)	The previous self-test completed having
					a test element that failed and the test
					element that failed is not known.
Total time to complete Offline 
data collection: 		( 8144) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 735) minutes.
Conveyance self-test routine
recommended polling time: 	 (   5) minutes.
SCT capabilities: 	       (0x303d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR-K   001   001   051    NOW  20658
  3 Spin_Up_Time            POS--K   200   190   021    -    9000
  4 Start_Stop_Count        -O--CK   096   096   000    -    4377
  5 Reallocated_Sector_Ct   PO--CK   200   200   140    -    0
  7 Seek_Error_Rate         -OSR-K   200   200   000    -    0
  9 Power_On_Hours          -O--CK   028   028   000    -    52780
 10 Spin_Retry_Count        -O--CK   100   100   000    -    0
 11 Calibration_Retry_Count -O--CK   100   253   000    -    0
 12 Power_Cycle_Count       -O--CK   100   100   000    -    89
192 Power-Off_Retract_Count -O--CK   200   200   000    -    57
193 Load_Cycle_Count        -O--CK   194   194   000    -    19342
194 Temperature_Celsius     -O---K   125   100   000    -    27
196 Reallocated_Event_Count -O--CK   200   200   000    -    0
197 Current_Pending_Sector  -O--CK   198   198   000    -    2132
198 Offline_Uncorrectable   ----CK   100   253   000    -    0
199 UDMA_CRC_Error_Count    -O--CK   200   200   000    -    0
200 Multi_Zone_Error_Rate   ---R--   200   200   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      5  Comprehensive SMART error log
0x03       GPL     R/O      6  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x21       GPL     R/O      1  Write stream error log
0x22       GPL     R/O      1  Read stream error log
0x30       GPL,SL  R/O      9  IDENTIFY DEVICE data log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa0-0xa7  GPL,SL  VS      16  Device vendor specific log
0xa8-0xb6  GPL,SL  VS       1  Device vendor specific log
0xb7       GPL,SL  VS      40  Device vendor specific log
0xbd       GPL,SL  VS       1  Device vendor specific log
0xc0       GPL,SL  VS       1  Device vendor specific log
0xc1       GPL     VS      93  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 10951 (device log contains only the most recent 24 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 10951 [6] occurred at disk power-on lifetime: 52774 hours (2198 days + 22 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 bc 35 c8 18 40 00  Error: UNC at LBA = 0x1bc35c818 = 7452608536

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 70 00 01 bc 35 c8 18 40 08  3d+21:45:23.776  READ FPDMA QUEUED
  47 00 00 00 01 00 00 00 00 00 30 e0 08  3d+21:45:23.776  READ LOG DMA EXT
  47 00 00 00 01 00 00 00 00 00 00 e0 08  3d+21:45:23.776  READ LOG DMA EXT
  ef 00 10 00 02 00 00 00 00 00 00 a0 08  3d+21:45:23.776  SET FEATURES [Enable SATA feature]
  27 00 00 00 00 00 00 00 00 00 00 e0 08  3d+21:45:23.775  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 10950 [5] occurred at disk power-on lifetime: 52774 hours (2198 days + 22 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 bc 35 c8 18 40 00  Error: UNC at LBA = 0x1bc35c818 = 7452608536

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 18 00 01 bc 35 c8 18 40 08  3d+21:45:19.690  READ FPDMA QUEUED
  60 00 08 00 10 00 01 bc 35 c8 10 40 08  3d+21:45:18.774  READ FPDMA QUEUED
  60 00 08 00 98 00 01 bc 35 c8 08 40 08  3d+21:45:17.817  READ FPDMA QUEUED
  60 00 08 00 90 00 01 bc 35 c8 00 40 08  3d+21:45:16.859  READ FPDMA QUEUED
  60 00 08 00 88 00 01 bc 35 c7 f8 40 08  3d+21:45:15.902  READ FPDMA QUEUED

Error 10949 [4] occurred at disk power-on lifetime: 52774 hours (2198 days + 22 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 bc 35 c7 b8 40 00  Error: UNC at LBA = 0x1bc35c7b8 = 7452608440

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 08 00 01 bc 35 c7 b8 40 08  3d+21:45:04.330  READ FPDMA QUEUED
  b0 00 d1 00 01 00 00 00 c2 4f 01 00 08  3d+21:45:04.326  SMART READ ATTRIBUTE THRESHOLDS [OBS-4]
  47 00 00 00 01 00 00 00 00 00 30 e0 08  3d+21:45:04.326  READ LOG DMA EXT
  47 00 00 00 01 00 00 00 00 00 00 e0 08  3d+21:45:04.326  READ LOG DMA EXT
  ef 00 10 00 02 00 00 00 00 00 00 a0 08  3d+21:45:04.326  SET FEATURES [Enable SATA feature]

Error 10948 [3] occurred at disk power-on lifetime: 52774 hours (2198 days + 22 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 bc 35 c7 b8 40 00  Error: UNC at LBA = 0x1bc35c7b8 = 7452608440

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 f8 00 01 bc 35 c7 b8 40 08  3d+21:45:00.255  READ FPDMA QUEUED
  b0 00 d0 00 01 00 00 00 c2 4f 00 00 08  3d+21:45:00.219  SMART READ DATA
  60 00 08 00 b0 00 01 bc 35 c7 b0 40 08  3d+21:44:59.274  READ FPDMA QUEUED
  ec 00 00 00 01 00 00 00 00 00 00 00 08  3d+21:44:59.273  IDENTIFY DEVICE
  47 00 00 00 01 00 00 00 00 00 30 e0 08  3d+21:44:59.273  READ LOG DMA EXT

Error 10947 [2] occurred at disk power-on lifetime: 52774 hours (2198 days + 22 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 bc 35 c7 b0 40 00  Error: UNC at LBA = 0x1bc35c7b0 = 7452608432

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 90 00 01 bc 35 c7 b0 40 08  3d+21:44:55.190  READ FPDMA QUEUED
  ec 00 00 00 01 00 00 00 00 00 00 00 08  3d+21:44:55.189  IDENTIFY DEVICE
  47 00 00 00 01 00 00 00 00 00 30 e0 08  3d+21:44:55.189  READ LOG DMA EXT
  47 00 00 00 01 00 00 00 00 00 00 e0 08  3d+21:44:55.189  READ LOG DMA EXT
  ef 00 10 00 02 00 00 00 00 00 00 a0 08  3d+21:44:55.189  SET FEATURES [Enable SATA feature]

Error 10946 [1] occurred at disk power-on lifetime: 52774 hours (2198 days + 22 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 bc 35 c7 b0 40 00  Error: UNC at LBA = 0x1bc35c7b0 = 7452608432

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 20 00 01 bc 35 c7 b0 40 08  3d+21:44:51.113  READ FPDMA QUEUED
  60 00 08 00 18 00 01 bc 35 c7 a8 40 08  3d+21:44:50.156  READ FPDMA QUEUED
  60 00 08 00 10 00 01 bc 35 c7 a0 40 08  3d+21:44:49.011  READ FPDMA QUEUED
  60 00 08 00 08 00 01 bc 35 c7 98 40 08  3d+21:44:48.054  READ FPDMA QUEUED
  60 00 08 00 00 00 01 bc 35 c7 90 40 08  3d+21:44:47.096  READ FPDMA QUEUED

Error 10945 [0] occurred at disk power-on lifetime: 52774 hours (2198 days + 22 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 bc 35 c7 38 40 00  Error: UNC at LBA = 0x1bc35c738 = 7452608312

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 28 00 01 bc 35 c7 38 40 08  3d+21:44:31.567  READ FPDMA QUEUED
  47 00 00 00 01 00 00 00 00 00 30 e0 08  3d+21:44:31.566  READ LOG DMA EXT
  47 00 00 00 01 00 00 00 00 00 00 e0 08  3d+21:44:31.566  READ LOG DMA EXT
  ef 00 10 00 02 00 00 00 00 00 00 a0 08  3d+21:44:31.566  SET FEATURES [Enable SATA feature]
  27 00 00 00 00 00 00 00 00 00 00 e0 08  3d+21:44:31.566  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 10944 [23] occurred at disk power-on lifetime: 52774 hours (2198 days + 22 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 bc 35 c7 38 40 00  Error: UNC at LBA = 0x1bc35c738 = 7452608312

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 68 00 01 bc 35 c7 38 40 08  3d+21:44:27.491  READ FPDMA QUEUED
  60 00 08 00 60 00 01 bc 35 c7 30 40 08  3d+21:44:26.544  READ FPDMA QUEUED
  60 00 08 00 58 00 01 bc 35 c7 28 40 08  3d+21:44:25.597  READ FPDMA QUEUED
  60 00 08 00 50 00 01 bc 35 c7 20 40 08  3d+21:44:24.639  READ FPDMA QUEUED
  60 00 08 00 80 00 01 bc 35 c7 18 40 08  3d+21:44:24.196  READ FPDMA QUEUED

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed: unknown failure    90%     52780         -
# 2  Short offline       Completed: unknown failure    90%     52776         -
# 3  Short offline       Completed: unknown failure    90%     52776         -
# 4  Extended offline    Completed: unknown failure    90%     52776         -
# 5  Short offline       Completed: unknown failure    90%     52776         -
# 6  Short offline       Completed: unknown failure    90%     52776         -
# 7  Short offline       Completed: unknown failure    90%     52776         -
# 8  Extended offline    Completed: unknown failure    90%     52776         -
# 9  Short offline       Completed without error       00%     52672         -
#10  Extended offline    Completed without error       00%     35027         -
#11  Short offline       Completed without error       00%     34934         -
#12  Short offline       Completed without error       00%     34768         -
#13  Short offline       Completed without error       00%     34601         -
#14  Short offline       Completed without error       00%     34433         -
#15  Extended offline    Completed without error       00%     34279         -
#16  Short offline       Completed without error       00%     34097         -
#17  Short offline       Completed without error       00%     33929         -
#18  Short offline       Completed without error       00%     33761         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       258 (0x0102)
Device State:                        Active (0)
Current Temperature:                    27 Celsius
Power Cycle Min/Max Temperature:     23/37 Celsius
Lifetime    Min/Max Temperature:      2/52 Celsius
Under/Over Temperature Limit Count:   0/0
Vendor specific:
00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/60 Celsius
Min/Max Temperature Limit:           -41/85 Celsius
Temperature History Size (Index):    478 (26)

Index    Estimated Time   Temperature Celsius
  27    2022-08-12 11:35    26  *******
 ...    ..( 55 skipped).    ..  *******
  83    2022-08-12 12:31    26  *******
  84    2022-08-12 12:32     ?  -
  85    2022-08-12 12:33    26  *******
  86    2022-08-12 12:34    27  ********
  87    2022-08-12 12:35    35  ****************
 ...    ..(  3 skipped).    ..  ****************
  91    2022-08-12 12:39    35  ****************
  92    2022-08-12 12:40     ?  -
  93    2022-08-12 12:41    35  ****************
 ...    ..(  6 skipped).    ..  ****************
 100    2022-08-12 12:48    35  ****************
 101    2022-08-12 12:49     ?  -
 102    2022-08-12 12:50    34  ***************
 103    2022-08-12 12:51    34  ***************
 104    2022-08-12 12:52     ?  -
 105    2022-08-12 12:53    34  ***************
 106    2022-08-12 12:54     ?  -
 107    2022-08-12 12:55    34  ***************
 108    2022-08-12 12:56     ?  -
 109    2022-08-12 12:57    34  ***************
 110    2022-08-12 12:58     ?  -
 111    2022-08-12 12:59    34  ***************
 112    2022-08-12 13:00     ?  -
 113    2022-08-12 13:01    34  ***************
 114    2022-08-12 13:02     ?  -
 115    2022-08-12 13:03    34  ***************
 116    2022-08-12 13:04     ?  -
 117    2022-08-12 13:05    34  ***************
 118    2022-08-12 13:06     ?  -
 119    2022-08-12 13:07    34  ***************
 120    2022-08-12 13:08     ?  -
 121    2022-08-12 13:09    34  ***************
 122    2022-08-12 13:10     ?  -
 123    2022-08-12 13:11    34  ***************
 124    2022-08-12 13:12    35  ****************
 125    2022-08-12 13:13     ?  -
 126    2022-08-12 13:14    35  ****************
 ...    ..(  3 skipped).    ..  ****************
 130    2022-08-12 13:18    35  ****************
 131    2022-08-12 13:19     ?  -
 132    2022-08-12 13:20    35  ****************
 ...    ..(  3 skipped).    ..  ****************
 136    2022-08-12 13:24    35  ****************
 137    2022-08-12 13:25     ?  -
 138    2022-08-12 13:26    35  ****************
 ...    ..(  6 skipped).    ..  ****************
 145    2022-08-12 13:33    35  ****************
 146    2022-08-12 13:34     ?  -
 147    2022-08-12 13:35    35  ****************
 ...    ..(  5 skipped).    ..  ****************
 153    2022-08-12 13:41    35  ****************
 154    2022-08-12 13:42     ?  -
 155    2022-08-12 13:43    35  ****************
 156    2022-08-12 13:44    35  ****************
 157    2022-08-12 13:45     ?  -
 158    2022-08-12 13:46    35  ****************
 ...    ..( 19 skipped).    ..  ****************
 178    2022-08-12 14:06    35  ****************
 179    2022-08-12 14:07    34  ***************
 180    2022-08-12 14:08    34  ***************
 181    2022-08-12 14:09    34  ***************
 182    2022-08-12 14:10    33  **************
 183    2022-08-12 14:11    33  **************
 184    2022-08-12 14:12    33  **************
 185    2022-08-12 14:13    32  *************
 186    2022-08-12 14:14    32  *************
 187    2022-08-12 14:15    32  *************
 188    2022-08-12 14:16    31  ************
 ...    ..(  3 skipped).    ..  ************
 192    2022-08-12 14:20    31  ************
 193    2022-08-12 14:21    30  ***********
 ...    ..(  3 skipped).    ..  ***********
 197    2022-08-12 14:25    30  ***********
 198    2022-08-12 14:26    29  **********
 ...    ..(  5 skipped).    ..  **********
 204    2022-08-12 14:32    29  **********
 205    2022-08-12 14:33    28  *********
 ...    ..( 12 skipped).    ..  *********
 218    2022-08-12 14:46    28  *********
 219    2022-08-12 14:47    27  ********
 ...    ..( 45 skipped).    ..  ********
 265    2022-08-12 15:33    27  ********
 266    2022-08-12 15:34    26  *******
 ...    ..( 41 skipped).    ..  *******
 308    2022-08-12 16:16    26  *******
 309    2022-08-12 16:17     ?  -
 310    2022-08-12 16:18    26  *******
 311    2022-08-12 16:19    27  ********
 ...    ..(  2 skipped).    ..  ********
 314    2022-08-12 16:22    27  ********
 315    2022-08-12 16:23    28  *********
 316    2022-08-12 16:24    28  *********
 317    2022-08-12 16:25    28  *********
 318    2022-08-12 16:26    29  **********
 ...    ..(  2 skipped).    ..  **********
 321    2022-08-12 16:29    29  **********
 322    2022-08-12 16:30    30  ***********
 ...    ..(  2 skipped).    ..  ***********
 325    2022-08-12 16:33    30  ***********
 326    2022-08-12 16:34    31  ************
 ...    ..(  3 skipped).    ..  ************
 330    2022-08-12 16:38    31  ************
 331    2022-08-12 16:39    32  *************
 ...    ..(  5 skipped).    ..  *************
 337    2022-08-12 16:45    32  *************
 338    2022-08-12 16:46    33  **************
 ...    ..(  4 skipped).    ..  **************
 343    2022-08-12 16:51    33  **************
 344    2022-08-12 16:52    32  *************
 345    2022-08-12 16:53    32  *************
 346    2022-08-12 16:54    32  *************
 347    2022-08-12 16:55    31  ************
 ...    ..(  3 skipped).    ..  ************
 351    2022-08-12 16:59    31  ************
 352    2022-08-12 17:00    30  ***********
 ...    ..(  3 skipped).    ..  ***********
 356    2022-08-12 17:04    30  ***********
 357    2022-08-12 17:05    29  **********
 ...    ..(  6 skipped).    ..  **********
 364    2022-08-12 17:12    29  **********
 365    2022-08-12 17:13    28  *********
 ...    ..( 12 skipped).    ..  *********
 378    2022-08-12 17:26    28  *********
 379    2022-08-12 17:27    27  ********
 ...    ..( 58 skipped).    ..  ********
 438    2022-08-12 18:26    27  ********
 439    2022-08-12 18:27    26  *******
 ...    ..( 64 skipped).    ..  *******
  26    2022-08-12 19:32    26  *******

SCT Error Recovery Control:
           Read:     70 (7.0 seconds)
          Write:     70 (7.0 seconds)

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2            5  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2            6  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x8000  4       361628  Vendor specific

2 hours ago, hawihoney said:

 

Hat sich etwas an den Werten verändert?

 

Ja.

Screenshot_20220812-193655_Firefox.thumb.png.e241f606c1ac04cc29ac6c708a38a142.png

Link to comment
Posted (edited)
2 hours ago, mgutt said:

Geh mal bitte hin und schließ die Platte in ihrem Original Gehäuse bzw über diese USB Platine an und mach dann mal einen SMART Test.

Da es ne WD Red NAS HDD 6 TB ist, existiert sowas nicht.

Edited by Revan335
Link to comment
1 hour ago, Revan335 said:

Da es ne WD Red NAS HDD 6 TB ist, existiert sowas nicht.

Da hab ich gerade zwei Threads vermischt. Dachte es wäre eine ausgebaute USB Platte gewesen.

 

Also jetzt bleibt denke ich nur noch mit Windows und dem Original Diagnostic Tool von WD zu testen. Wenn es da die selben Probleme gibt, dann ab in den Müll damit.

Link to comment

Der Quick Test von denen sagt to many Bad Sectors und bricht währenddes Runs ab.

16 hours ago, mgutt said:

Also jetzt bleibt denke ich nur noch mit Windows und dem Original Diagnostic Tool von WD zu testen.

Damit scheint sie es wohl hinter sich zu haben.

Aber schon interessant das eine vorher mit keiner Warnung/SMART Error sich so schnell mit diesem Fehlerbild dazu entscheidet zu sterben.

 

Aber dann muss ich wohl ne andere Platte als Parity wählen und damit das Array einrichten.

 

Vielen Dank an euch für die Hilfe!

Link to comment
  • 1 month later...

Hallo zusammen,

ich habe ein ähnliches Problem mit meiner Parity-HDD.

Gestern habe ich den Mover von Hand angestoßen, ein paar Sekunden später erhielt ich eine Smart Warnmeldung nach der anderen.

Der Current pending sector ist auf 418 hochgeschossen. Die HDD ist gerade einmal 8 Monate alt.

Ist die Platte hinüber?

Spoiler

smartctl;

root@unraid:~# smartctl -a /dev/sdd
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.10.28-Unraid] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Toshiba MG08ACA... Enterprise Capacity HDD
Device Model:     TOSHIBA MG08ACA16TE
Serial Number:    X1N0A0KSFVGG
LU WWN Device Id: 5 000039 b38da0a4f
Firmware Version: 0102
User Capacity:    16,000,900,661,248 bytes [16.0 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-3 T13/2161-D revision 5
SATA Version is:  SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Thu Sep 15 10:42:06 2022 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x84) Offline data collection activity
                                        was suspended by an interrupting command from host.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (  120) seconds.
Offline data collection
capabilities:                    (0x5b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        (1428) minutes.
SCT capabilities:              (0x003d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   095   050    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0005   100   100   050    Pre-fail  Offline      -       0
  3 Spin_Up_Time            0x0027   100   100   001    Pre-fail  Always       -       8109
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       1567
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000b   100   100   050    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0005   100   100   050    Pre-fail  Offline      -       0
  9 Power_On_Hours          0x0032   088   088   000    Old_age   Always       -       5191
 10 Spin_Retry_Count        0x0033   100   100   030    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       91
 23 Helium_Condition_Lower  0x0023   100   100   075    Pre-fail  Always       -       0
 24 Helium_Condition_Upper  0x0023   100   100   075    Pre-fail  Always       -       0
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       28
193 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       1855
194 Temperature_Celsius     0x0022   100   100   000    Old_age   Always       -       41 (Min/Max 20/46)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   100   100   000    Old_age   Always       -       418
198 Offline_Uncorrectable   0x0030   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
220 Disk_Shift              0x0002   100   100   000    Old_age   Always       -       270139429
222 Loaded_Hours            0x0032   097   097   000    Old_age   Always       -       1299
223 Load_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
224 Load_Friction           0x0022   100   100   000    Old_age   Always       -       0
226 Load-in_Time            0x0026   100   100   000    Old_age   Always       -       534
240 Head_Flying_Hours       0x0001   100   100   001    Pre-fail  Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%      5191         -
# 2  Extended offline    Aborted by host               90%      5180         -
# 3  Short offline       Completed without error       00%      5179         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

 

Gruß Frank

Link to comment
16 minutes ago, frank80 said:

Ist die Platte hinüber?

 

Alle diese "*reallocated" Werte sind Ausdruck, dass etwas nicht in Ordnung ist. Gerade bei einer so kurzen Lebenszeit würde ich persönlich diese Platte zurückgeben.

 

Dieser Wert kann sich bei späteren erfolgreichen Zugriffen wieder reduzieren. Die Erfahrung zeigt aber, dass diese Werte später zu "Reallocated_Sector_Ct" werden. Und sobald bei mir dort eine 1 steht, fange ich schon an diese Platte genau zu beäugen.

 

Was Du tun kannst:

 

1.) Hast Du eine gleichgroße Platte vorliegen, dann tausche

2.) Wenn Du keine gleichgroße Platte hast, und Du Deine wichtigen Daten gesichert hast, dann kannst Du nach einem Reboot nochmal einen Parity-Check durchführen. Im glücklichen Fall reduziert sich der Wert, im schlechten Fall wird er umgewandelt zu "Reallocated_Sector_Ct"

 

Link to comment

Hallo,

2 hours ago, hawihoney said:

1.) Hast Du eine gleichgroße Platte vorliegen, dann tausche

2.) Wenn Du keine gleichgroße Platte hast, und Du Deine wichtigen Daten gesichert hast, dann kannst Du nach einem Reboot nochmal einen Parity-Check durchführen. Im glücklichen Fall reduziert sich der Wert, im schlechten Fall wird er umgewandelt zu "Reallocated_Sector_Ct"

Ich habe noch eine identische HDD, die ist allerdings meine Backup-HDD. Die würde ich ungern opfern.

Der Parity-Check läuft seit ca. 14 Std. und ich habe schon die ersten Meldungen mit Errors und dass der Current pending sector wieder auf 0 steht erhalten, siehe Bild.

 

43 minutes ago, DataCollector said:

Nutzt Du Powertop?

Ja

 

15-09-2022 13_42_03-unraid_Main – Mozilla Firefox.png

 

smartctl;

Spoiler

root@unraid:~# smartctl -a /dev/sdd
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.10.28-Unraid] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Toshiba MG08ACA... Enterprise Capacity HDD
Device Model:     TOSHIBA MG08ACA16TE
Serial Number:    X1N0A0KSFVGG
LU WWN Device Id: 5 000039 b38da0a4f
Firmware Version: 0102
User Capacity:    16,000,900,661,248 bytes [16.0 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-3 T13/2161-D revision 5
SATA Version is:  SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Thu Sep 15 13:59:05 2022 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x84) Offline data collection activity
                                        was suspended by an interrupting command from host.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (  120) seconds.
Offline data collection
capabilities:                    (0x5b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        (1428) minutes.
SCT capabilities:              (0x003d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   095   050    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0005   100   100   050    Pre-fail  Offline      -       0
  3 Spin_Up_Time            0x0027   100   100   001    Pre-fail  Always       -       8109
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       1567
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000b   100   100   050    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0005   100   100   050    Pre-fail  Offline      -       0
  9 Power_On_Hours          0x0032   088   088   000    Old_age   Always       -       5194
 10 Spin_Retry_Count        0x0033   100   100   030    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       91
 23 Helium_Condition_Lower  0x0023   100   100   075    Pre-fail  Always       -       0
 24 Helium_Condition_Upper  0x0023   100   100   075    Pre-fail  Always       -       0
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       28
193 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       1855
194 Temperature_Celsius     0x0022   100   100   000    Old_age   Always       -       40 (Min/Max 20/46)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
220 Disk_Shift              0x0002   100   100   000    Old_age   Always       -       270139429
222 Loaded_Hours            0x0032   097   097   000    Old_age   Always       -       1303
223 Load_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
224 Load_Friction           0x0022   100   100   000    Old_age   Always       -       0
226 Load-in_Time            0x0026   100   100   000    Old_age   Always       -       534
240 Head_Flying_Hours       0x0001   100   100   001    Pre-fail  Offline      -       0

SMART Error Log Version: 1
ATA Error Count: 1
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 1 occurred at disk power-on lifetime: 5193 hours (216 days + 9 hours)
  When the command that caused the error occurred, the device was in standby mode.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 43 18 c8 e2 01 40  Error: UNC at LBA = 0x0001e2c8 = 123592

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 40 a0 90 f8 01 40 00   7d+00:14:44.584  READ FPDMA QUEUED
  60 40 98 50 f3 01 40 00   7d+00:14:42.334  READ FPDMA QUEUED
  60 40 90 10 ee 01 40 00   7d+00:14:42.331  READ FPDMA QUEUED
  60 40 88 d0 e8 01 40 00   7d+00:14:42.326  READ FPDMA QUEUED
  60 40 80 90 e3 01 40 00   7d+00:14:42.323  READ FPDMA QUEUED

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%      5191         -
# 2  Extended offline    Aborted by host               90%      5180         -
# 3  Short offline       Completed without error       00%      5179         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

 

 

Edited by frank80
Link to comment

Ich habe auf der Start-Seite jetzt 1024 Fehler im Array

 

 

20 minutes ago, hawihoney said:

Beim erneuten Lesen wurde an den betreffenden Stellen kein Fehler mehr festgestellt. Alles gut - für mich nicht nachvollziehbar - aber gut.

 

In smartctl habe ich diese Meldung

SMART Error Log Version: 1
ATA Error Count: 1

 

15-09-2022 15_20_24-unraid_Main – Mozilla Firefox.png

Link to comment
11 minutes ago, frank80 said:

Ich habe auf der Start-Seite jetzt 1024 Fehler im Array

 

Hä, smartctl hat doch eine makellose Festplatte gezeigt. Wie passt das zeitlich? Von wann sind die Errors und von wann smartctl.

 

Ich würde das ganze mal im Maintenance Mode durchführen - ohne zusätzliche Plugins oder Befehle im go Skript.

 

Link to comment

Hallo,

 

1 hour ago, hawihoney said:

Wie passt das zeitlich? Von wann sind die Errors und von wann smartctl.

Eigentlich in der Zeitfolge, wie ich geschrieben bzw. geantwortet habe.

  1. Current pending sector = 418
  2. Array Error´s (1024)
  3. Current pending sector = 0

Die beiden Ergebnisse von smartctl habe ich direkt vor dem Schreiben im Forum ausgelesen.

 

ca. 11 Uhr

Spoiler

smartctl;

root@unraid:~# smartctl -a /dev/sdd
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.10.28-Unraid] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Toshiba MG08ACA... Enterprise Capacity HDD
Device Model:     TOSHIBA MG08ACA16TE
Serial Number:    X1N0A0KSFVGG
LU WWN Device Id: 5 000039 b38da0a4f
Firmware Version: 0102
User Capacity:    16,000,900,661,248 bytes [16.0 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-3 T13/2161-D revision 5
SATA Version is:  SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Thu Sep 15 10:42:06 2022 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x84) Offline data collection activity
                                        was suspended by an interrupting command from host.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (  120) seconds.
Offline data collection
capabilities:                    (0x5b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        (1428) minutes.
SCT capabilities:              (0x003d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   095   050    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0005   100   100   050    Pre-fail  Offline      -       0
  3 Spin_Up_Time            0x0027   100   100   001    Pre-fail  Always       -       8109
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       1567
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000b   100   100   050    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0005   100   100   050    Pre-fail  Offline      -       0
  9 Power_On_Hours          0x0032   088   088   000    Old_age   Always       -       5191
 10 Spin_Retry_Count        0x0033   100   100   030    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       91
 23 Helium_Condition_Lower  0x0023   100   100   075    Pre-fail  Always       -       0
 24 Helium_Condition_Upper  0x0023   100   100   075    Pre-fail  Always       -       0
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       28
193 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       1855
194 Temperature_Celsius     0x0022   100   100   000    Old_age   Always       -       41 (Min/Max 20/46)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   100   100   000    Old_age   Always       -       418
198 Offline_Uncorrectable   0x0030   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
220 Disk_Shift              0x0002   100   100   000    Old_age   Always       -       270139429
222 Loaded_Hours            0x0032   097   097   000    Old_age   Always       -       1299
223 Load_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
224 Load_Friction           0x0022   100   100   000    Old_age   Always       -       0
226 Load-in_Time            0x0026   100   100   000    Old_age   Always       -       534
240 Head_Flying_Hours       0x0001   100   100   001    Pre-fail  Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%      5191         -
# 2  Extended offline    Aborted by host               90%      5180         -
# 3  Short offline       Completed without error       00%      5179         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

 

 17:21 Uhr

Spoiler

root@unraid:~# smartctl -a /dev/sdd
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.10.28-Unraid] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Toshiba MG08ACA... Enterprise Capacity HDD
Device Model:     TOSHIBA MG08ACA16TE
Serial Number:    X1N0A0KSFVGG
LU WWN Device Id: 5 000039 b38da0a4f
Firmware Version: 0102
User Capacity:    16,000,900,661,248 bytes [16.0 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-3 T13/2161-D revision 5
SATA Version is:  SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Thu Sep 15 17:22:04 2022 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x84) Offline data collection activity
                                        was suspended by an interrupting command from host.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (  120) seconds.
Offline data collection
capabilities:                    (0x5b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        (1428) minutes.
SCT capabilities:              (0x003d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   095   050    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0005   100   100   050    Pre-fail  Offline      -       0
  3 Spin_Up_Time            0x0027   100   100   001    Pre-fail  Always       -       8109
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       1567
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000b   100   100   050    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0005   100   100   050    Pre-fail  Offline      -       0
  9 Power_On_Hours          0x0032   088   088   000    Old_age   Always       -       5198
 10 Spin_Retry_Count        0x0033   100   100   030    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       91
 23 Helium_Condition_Lower  0x0023   100   100   075    Pre-fail  Always       -       0
 24 Helium_Condition_Upper  0x0023   100   100   075    Pre-fail  Always       -       0
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       28
193 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       1855
194 Temperature_Celsius     0x0022   100   100   000    Old_age   Always       -       40 (Min/Max 20/46)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
220 Disk_Shift              0x0002   100   100   000    Old_age   Always       -       270139429
222 Loaded_Hours            0x0032   097   097   000    Old_age   Always       -       1306
223 Load_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
224 Load_Friction           0x0022   100   100   000    Old_age   Always       -       0
226 Load-in_Time            0x0026   100   100   000    Old_age   Always       -       534
240 Head_Flying_Hours       0x0001   100   100   001    Pre-fail  Offline      -       0

SMART Error Log Version: 1
ATA Error Count: 1
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 1 occurred at disk power-on lifetime: 5193 hours (216 days + 9 hours)
  When the command that caused the error occurred, the device was in standby mode.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 43 18 c8 e2 01 40  Error: UNC at LBA = 0x0001e2c8 = 123592

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 40 a0 90 f8 01 40 00   7d+00:14:44.584  READ FPDMA QUEUED
  60 40 98 50 f3 01 40 00   7d+00:14:42.334  READ FPDMA QUEUED
  60 40 90 10 ee 01 40 00   7d+00:14:42.331  READ FPDMA QUEUED
  60 40 88 d0 e8 01 40 00   7d+00:14:42.326  READ FPDMA QUEUED
  60 40 80 90 e3 01 40 00   7d+00:14:42.323  READ FPDMA QUEUED

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%      5191         -
# 2  Extended offline    Aborted by host               90%      5180         -
# 3  Short offline       Completed without error       00%      5179         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

 

 

Das interessante ist der SMART Error Log

ca. 11 Uhr

SMART Error Log Version: 1
No Errors Logged

und 17:21

SMART Error Log Version: 1
ATA Error Count: 1

 

 

 

Link to comment
1 hour ago, frank80 said:

Eigentlich in der Zeitfolge, wie ich geschrieben bzw. geantwortet habe.

 

Als Test würde ich mal einen "Non-correcting" parity check machen (also Checkbox bei "Write corrections to parity" leer lassen). Damit wird garantiert alles gelesen aber nichts geschrieben. Den kann man jederzeit abbrechen. Danach weißt Du ob Fehler existieren und wenn ja wie viele. Anschließend kannst Du entscheiden wie Du weiter vorgehst.

 

Link to comment

Guten Abend zusammen und danke für eure Hilfe. 👍

 

Als Nächstes werde ich Folgendes versuchen;

  1. Powertop in der /boot/config/go auskommentieren
  2. reboot
  3. Write corrections to parity deaktivieren
  4. Parity-Check läuft bereits (der letzte Check wurde vor 30 Min. beendet und ergab keine Fehler etc.)

 

Gruß Frank

 

Nachtrag;

die Fehler auf der Startseite sind jetzt auch wieder weg, siehe Bild...

 

16-09-2022 00_55_51-unraid_Main – Mozilla Firefox.png

Edited by frank80
Link to comment

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.