So my hardware failed after 4 years. Now i have change it from x299 to z690 setup 12600kf cpu  z690 gigabyte motherboard ultra. Intel nic also installed killer 2100 nic. So i have the ip address set static in unraid and can not ping that address. timed out. If i go on the usb stick and change the ip address of unraid by one digit i can ping the unraid server but can not loggin to the web browser address.  ip address refuses. Does anyone know what might be causing this?  Do i need to change the old motherboards mac address some how on the stick or in the text os loggin in?  Also if i try to load the unraid gui os on the unraid server it loads to a blank screen. 

3 hours ago, ssmokeyy said:

So my hardware failed after 4 years. Now i have change it from x299 to z690 setup 12600kf cpu  z690 gigabyte motherboard ultra. Intel nic also installed killer 2100 nic. So i have the ip address set static in unraid and can not ping that address. timed out. If i go on the usb stick and change the ip address of unraid by one digit i can ping the unraid server but can not loggin to the web browser address.  ip address refuses. Does anyone know what might be causing this?  Do i need to change the old motherboards mac address some how on the stick or in the text os loggin in?  Also if i try to load the unraid gui os on the unraid server it loads to a blank screen. 

Which NIC is eth0 as this will be the one unraid uses for the GUI.

 

My Z690 mother board has a 2.5Gb Intel nic which needed a later kernel than is in 6.9.2

 

run ifconfig, ethtool eth0 and ethtool eth1 to find NIC details

 

you may need to swap the NICs around.

 

The intel 2.5 gbe is set to eth0. Its built on board the motherboard. I can turn off the on board nic and just run the killer nic if that would get me in to update.  Do I need to worry about the Mac info at all at this point? 

Turned off internal nic and tried just the killer 2100 nic card and no luck.  Could this be a to old of a unraid version to work with the 12th gen?

two things that I would suggest here... update the OS(folks here dont like troubleshooting outdated software) and post Diags...

 

it's possible that the IP address has changed due to a new nic and DHCP providing a different IP... have you validated that you have the correct IP via the console(using an external monitor connected to the server)?

5 hours ago, ssmokeyy said:

Turned off internal nic and tried just the killer 2100 nic card and no luck.  Could this be a to old of a unraid version to work with the 12th gen?

Are you able to get diagnostics?

Yes to checking the ip on the console. It is the same as i had it set before. But I have also tried changing it and still no difference.  I'm ok with updating the os just not sure how to do it with out loosing my data on the stick.     SimonF not sure what your asking. If your asking if i can loggin to the os text command line that is a yes.  Os gui is a no it will not load to a screen just loads to a blank screen.  

You might try accessing the webconsole via IP and using private/incognito mode... and also running the following command in CMD is a good idea 'ipconfig /flushdns'

I have tried ping sites from the unraid box and It doesn't see anything.  

 

check network settings... perhaps you gateway IP has changed... you might try setting the server up via DHCP and making it's new IP static via your router

4 hours ago, ssmokeyy said:

Yes to checking the ip on the console. It is the same as i had it set before. But I have also tried changing it and still no difference.  I'm ok with updating the os just not sure how to do it with out loosing my data on the stick.     SimonF not sure what your asking. If your asking if i can loggin to the os text command line that is a yes.  Os gui is a no it will not load to a screen just loads to a blank screen.  

if you run diagnostics on the comand line will creat a zip file on the flash. not sure if you have a way to copy off and post on here?

Turned off internal nic and tried just the killer 2100 nic card and no luck.  Could this be a to old of a unraid version to work with the 12th gen?

 

Not sure what command does diagnostics. I can get files off the Usb stick from my windows system.   Is there a good site or page that talks about updating the os to a newer version with out looking the key or info. 

Moved the usb stick to an old workstation pc and got into unraid. I have updated to 6.11.3 going to check it one more time and than try it again on the new server. 

So i got unraid working. Update on another workstation worked. But now my nextcloud is not working. Says i need to update php 7.4 to php 8.0 or newer. Not finding a lot of info about this on the unraid platform.  Any tips on doing this?

 

7 minutes ago, ssmokeyy said:

So i got unraid working. Update on another workstation worked. But now my nextcloud is not working. Says i need to update php 7.4 to php 8.0 or newer. Not finding a lot of info about this on the unraid platform.  Any tips on doing this?

 

Not sure how you run nextcloud but this will be the php package within the docker/vm not unraid.

I setup nextcloud the same way spaceinvaderone did. So now im trying to loggin to nextcloud but can't find my user name its been forever since i had to make any changes

1 hour ago, ssmokeyy said:

I setup nextcloud the same way spaceinvaderone did. So now im trying to loggin to nextcloud but can't find my user name its been forever since i had to make any changes

So this one statement is conflicting... you say that you havent "make any changes" yet you just setup nextcloud... and now nextcloud isnt working... 

Please consider marking this thread as solved and make a new post on the relevant forum/thread to your new issue... 

Edited December 30, 20223 yr by mathomas3