Hello and good morning!

 

So last night I decided to upgrade my components from an old PC I had. The hard drives/sas controllers(2) all stayed. New mobo/cpu/ram/gpu/psu.

 

When I booted up only the cache drive (which is an nvme) is recognized, all the hard drives that pass through the sas controller are not showing up. During boot the controllers that they see hard drives. I cannot get into the configuration though for some reason. After a google search it may be becuase i am using a usb keyborad and not a ps/2 keyboard...idk about that but I will try one tonight.

 

All of my hard drives show no device on unraid. Any ideas?

tower-diagnostics-20230302-2112.zip

Mar  2 18:11:02 Tower kernel: megasas: 07.714.04.00-rc1
Mar  2 18:11:02 Tower kernel: megaraid_sas 0000:25:00.0: BAR:0x1  BAR's base_addr(phys):0x00000000f7360000  mapped virt_addr:0x0000000044f6b965
Mar  2 18:11:02 Tower kernel: megaraid_sas 0000:25:00.0: FW now in Ready state
Mar  2 18:11:02 Tower kernel: megaraid_sas 0000:25:00.0: 63 bit DMA mask and 32 bit consistent mask
Mar  2 18:11:02 Tower kernel: megaraid_sas 0000:25:00.0: requested/available msix 1/1
Mar  2 18:11:02 Tower kernel: megaraid_sas 0000:25:00.0: current msix/online cpus    : (1/16)
Mar  2 18:11:02 Tower kernel: megaraid_sas 0000:25:00.0: RDPQ mode    : (disabled)
Mar  2 18:11:02 Tower kernel: megaraid_sas 0000:25:00.0: Failed to init firmware
Mar  2 18:11:02 Tower kernel: megaraid_sas 0000:25:00.0: Failed from megasas_init_fw 6406
Mar  2 18:11:02 Tower kernel: megaraid_sas 0000:28:00.0: BAR:0x1  BAR's base_addr(phys):0x00000000f7a60000  mapped virt_addr:0x0000000044f6b965
Mar  2 18:11:02 Tower kernel: megaraid_sas 0000:28:00.0: FW now in Ready state
Mar  2 18:11:02 Tower kernel: megaraid_sas 0000:28:00.0: 63 bit DMA mask and 32 bit consistent mask
Mar  2 18:11:02 Tower kernel: megaraid_sas 0000:28:00.0: requested/available msix 1/1
Mar  2 18:11:02 Tower kernel: megaraid_sas 0000:28:00.0: current msix/online cpus    : (1/16)
Mar  2 18:11:02 Tower kernel: megaraid_sas 0000:28:00.0: RDPQ mode    : (disabled)
Mar  2 18:11:02 Tower kernel: megaraid_sas 0000:28:00.0: Failed to init firmware
Mar  2 18:11:02 Tower kernel: megaraid_sas 0000:28:00.0: Failed from megasas_init_fw 6406

 

Both RAID controllers are failing to initialize and load the driver, also note that RAID controllers are not recommended, they should be flash to LSI IT mode, which uses the mpt3sas driver, also usually much more reliable than the megaraid driver.

Thanks for looking at that Jorge, I will see if i can resolve from the configuration if I can ever get into that and look into flashing the LSI IT if that is possible.