Jump to content

disk error now cannot add


Recommended Posts

smartctl 5.40 2010-10-16 r3189 [i486-slackware-linux-gnu] (local build)

Copyright © 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

 

=== START OF INFORMATION SECTION ===

Model Family:    Western Digital Caviar Green (Adv. Format) family

Device Model:    WDC WD20EARS-00MVWB0

Serial Number:    WD-WMAZA0648260

Firmware Version: 51.0AB51

User Capacity:    2,000,398,934,016 bytes

Device is:        In smartctl database [for details use: -P show]

ATA Version is:  8

ATA Standard is:  Exact ATA specification draft version not indicated

Local Time is:    Wed Sep 28 04:22:49 2011 Local time zone must be set--see zic m

SMART support is: Available - device has SMART capability.

SMART support is: Enabled

 

=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED

 

General SMART Values:

Offline data collection status:  (0x84) Offline data collection activity

was suspended by an interrupting command from host.

Auto Offline Data Collection: Enabled.

Self-test execution status:      (  0) The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: (35880) seconds.

Offline data collection

capabilities: (0x7b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

Conveyance Self-test supported.

Selective Self-test supported.

SMART capabilities:            (0x0003) Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability:        (0x01) Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time: (  2) minutes.

Extended self-test routine

recommended polling time: ( 255) minutes.

Conveyance self-test routine

recommended polling time: (  5) minutes.

SCT capabilities:       (0x3035) SCT Status supported.

SCT Feature Control supported.

SCT Data Table supported.

 

SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG    VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

  1 Raw_Read_Error_Rate    0x002f  200  199  051    Pre-fail  Always      -      162

  3 Spin_Up_Time            0x0027  170  165  021    Pre-fail  Always      -      6491

  4 Start_Stop_Count        0x0032  099  099  000    Old_age  Always      -      1201

  5 Reallocated_Sector_Ct  0x0033  200  200  140    Pre-fail  Always      -      0

  7 Seek_Error_Rate        0x002e  200  200  000    Old_age  Always      -      0

  9 Power_On_Hours          0x0032  093  093  000    Old_age  Always      -      5136

10 Spin_Retry_Count        0x0032  100  100  000    Old_age  Always      -      0

11 Calibration_Retry_Count 0x0032  100  100  000    Old_age  Always      -      0

12 Power_Cycle_Count      0x0032  100  100  000    Old_age  Always      -      194

192 Power-Off_Retract_Count 0x0032  200  200  000    Old_age  Always      -      94

193 Load_Cycle_Count        0x0032  197  197  000    Old_age  Always      -      9744

194 Temperature_Celsius    0x0022  113  108  000    Old_age  Always      -      37

196 Reallocated_Event_Count 0x0032  200  200  000    Old_age  Always      -      0

197 Current_Pending_Sector  0x0032  200  200  000    Old_age  Always      -      0

198 Offline_Uncorrectable  0x0030  200  200  000    Old_age  Offline      -      0

199 UDMA_CRC_Error_Count    0x0032  200  200  000    Old_age  Always      -      0

200 Multi_Zone_Error_Rate  0x0008  200  200  000    Old_age  Offline      -      0

 

SMART Error Log Version: 1

No Errors Logged

 

SMART Self-test log structure revision number 1

No self-tests have been logged.  [To run self-tests, use: smartctl -t]

 

 

SMART Selective self-test log data structure revision number 1

SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

    1        0        0  Not_testing

    2        0        0  Not_testing

    3        0        0  Not_testing

    4        0        0  Not_testing

    5        0        0  Not_testing

Selective self-test flags (0x0):

  After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.

 

 

Link to comment

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...