October 7, 201114 yr Does this parity drive look ok to you guys? Warning: ATA error count 192 inconsistent with error log pointer 5 dont understand that warning === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Green family Device Model: WDC WD20EADS-00R6B0 Serial Number: WD-WCAVY2269670 Firmware Version: 01.00A01 User Capacity: 2,000,398,934,016 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Fri Oct 7 11:34:25 2011 MDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (43200) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 198 154 021 Pre-fail Always - 7091 4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2197 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0 9 Power_On_Hours 0x0032 082 082 000 Old_age Always - 13417 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 51 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 42 193 Load_Cycle_Count 0x0032 191 191 000 Old_age Always - 27190 194 Temperature_Celsius 0x0022 121 114 000 Old_age Always - 31 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 14 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 2 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 SMART Error Log Version: 1 Warning: ATA error count 192 inconsistent with error log pointer 5 ATA Error Count: 192 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 192 occurred at disk power-on lifetime: 12852 hours (535 days + 12 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 fa 6c 55 ea Error: UNC at LBA = 0x0a556cfa = 173370618 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 07 6c 55 ea 08 10:05:09.385 READ DMA ef 10 02 00 00 00 a0 08 10:05:09.385 SET FEATURES [Reserved for Serial ATA] ec 00 00 00 00 00 a0 08 10:05:09.379 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 10:05:09.379 SET FEATURES [set transfer mode] Error 191 occurred at disk power-on lifetime: 12852 hours (535 days + 12 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 fa 6c 55 ea Error: UNC at LBA = 0x0a556cfa = 173370618 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 07 6c 55 ea 08 10:05:06.810 READ DMA ef 10 02 00 00 00 a0 08 10:05:06.810 SET FEATURES [Reserved for Serial ATA] ec 00 00 00 00 00 a0 08 10:05:06.804 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 10:05:06.804 SET FEATURES [set transfer mode] Error 190 occurred at disk power-on lifetime: 12852 hours (535 days + 12 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 fa 6c 55 ea Error: UNC at LBA = 0x0a556cfa = 173370618 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 07 6c 55 ea 08 10:05:04.079 READ DMA ef 10 02 00 00 00 a0 08 10:05:04.079 SET FEATURES [Reserved for Serial ATA] ec 00 00 00 00 00 a0 08 10:05:04.073 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 10:05:04.073 SET FEATURES [set transfer mode] Error 189 occurred at disk power-on lifetime: 12852 hours (535 days + 12 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 fa 6c 55 ea Error: UNC at LBA = 0x0a556cfa = 173370618 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 07 6c 55 ea 08 10:05:01.360 READ DMA ef 10 02 00 00 00 a0 08 10:05:01.360 SET FEATURES [Reserved for Serial ATA] ec 00 00 00 00 00 a0 08 10:05:01.354 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 10:05:01.354 SET FEATURES [set transfer mode] SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 12980 - # 2 Extended offline Completed: read failure 90% 11260 1634791 # 3 Short offline Interrupted (host reset) 90% 10393 - # 4 Short offline Aborted by host 90% 10391 - # 5 Short offline Aborted by host 70% 10391 - # 6 Extended offline Completed: read failure 90% 9983 45307611 # 7 Short offline Aborted by host 50% 9980 - # 8 Short offline Aborted by host 10% 9980 - # 9 Extended offline Completed: read failure 90% 9790 30300665 #10 Short offline Completed without error 00% 9789 - #11 Short offline Completed without error 00% 8827 - #12 Extended offline Completed: read failure 90% 8816 35253715 #13 Short offline Aborted by host 80% 8816 - #14 Short offline Aborted by host 80% 8816 - #15 Short offline Completed without error 00% 8816 - #16 Short offline Aborted by host 90% 8816 - #17 Short offline Aborted by host 90% 8816 - #18 Short offline Completed without error 00% 8816 - #19 Extended offline Completed: read failure 90% 8459 27516853 #20 Extended offline Completed: read failure 90% 7671 27516853 #21 Extended offline Completed: read failure 90% 7671 27516853 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. thanks
October 7, 201114 yr Author cache drive smartctl -a -d ata /dev/sdh (cache) smartctl 5.40 2010-10-16 r3189 [i486-slackware-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.12 family Device Model: ST3500418AS Serial Number: 9VM5HX2G Firmware Version: CC44 User Capacity: 500,107,862,016 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Fri Oct 7 11:49:58 2011 MDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 96) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 127135937 3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 917 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 070 060 030 Pre-fail Always - 12436186 9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 3085 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 917 183 Runtime_Bad_Block 0x0000 100 100 000 Old_age Offline - 0 184 End-to-End_Error 0x0032 096 096 099 Old_age Always FAILING_NOW 4 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 097 000 Old_age Always - 4295033105 189 High_Fly_Writes 0x003a 098 098 000 Old_age Always - 2 190 Airflow_Temperature_Cel 0x0022 073 054 045 Old_age Always - 27 (Min/Max 25/31) 194 Temperature_Celsius 0x0022 027 046 000 Old_age Always - 27 (0 18 0 0) 195 Hardware_ECC_Recovered 0x001a 047 028 000 Old_age Always - 127135937 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 32353988646138 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 4022005532 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 554943086 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. does this mean its going to fail any second now? my disk 4 has Hardware_ECC_Recovered 217883719 and some other things smartctl -a -d ata /dev/sdg (disk4) smartctl 5.40 2010-10-16 r3189 [i486-slackware-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F1 DT series Device Model: SAMSUNG HD103UJ Serial Number: S13PJ1EQ302581 Firmware Version: 1AA01109 User Capacity: 1,000,203,804,160 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 3b Local Time is: Fri Oct 7 11:51:12 2011 MDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (11847) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 198) minutes. Conveyance self-test routine recommended polling time: ( 21) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 098 051 Pre-fail Always - 5 3 Spin_Up_Time 0x0007 071 071 011 Pre-fail Always - 9400 4 Start_Stop_Count 0x0032 097 097 000 Old_age Always - 2594 5 Reallocated_Sector_Ct 0x0033 099 099 010 Pre-fail Always - 31 7 Seek_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0 8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail Offline - 10703 9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 14992 10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0 11 Calibration_Retry_Count 0x0012 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1430 13 Read_Soft_Error_Rate 0x000e 100 098 000 Old_age Always - 5 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0033 100 100 099 Pre-fail Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 48 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 079 059 000 Old_age Always - 21 (Min/Max 19/28) 194 Temperature_Celsius 0x0022 077 058 000 Old_age Always - 23 (Min/Max 14/30) 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 217883719 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 1 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 100 100 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 0 201 Soft_Read_Error_Rate 0x000a 100 100 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 0 Warning: ATA Specification requires self-test log structure revision number = 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 8695 - # 2 Extended offline Aborted by host 90% 8695 - Note: selective self-test log revision number (0) not 1 implies that no selective self-test has ever been run SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
October 7, 201114 yr Device Model: ST3500418AS Serial Number: 9VM5HX2G This drive has 14 sectors pending reallocation. The sectors will each be reallocated the next time a write to one of them fails again. Then the reallocated sector count will increase. If the next write succeeds the sector will not be reallocated. Device Model: SAMSUNG HD103UJ Serial Number: S13PJ1EQ302581 This drive has 31 sectors reallocated and 1 pending. Watch the reallocated and pending counts on these drives. If they continue to rise then RMA these drives. Device Model: ST3500418AS Serial Number: 9VM5HX2G This drive has already failed and should be RMAed.
October 8, 201114 yr Author what about that ata error count that keeps going up? its at 193 right now today it was 192
October 8, 201114 yr That means nothing: http://sourceforge.net/apps/trac/smartmontools/wiki/FAQ#Warning:ATAerrorcount9inconsistentwitherrorlogpointer5Whatsthemeaningofthissmartctlmessage
Archived
This topic is now archived and is closed to further replies.