April 11, 20242 yr As you can see in the picture, there is a disk that has come off. The disk that has died will be replaced with a 4TB Sata SSD, but to be able to do that, I have to make a "New Config"? Does this mean that the data on disk 1, which for some reason is not emulated, cannot be recreated? A little extra info: There are 18 usable TB. Approx. 2 TB on each disk was used, 6 TB in total. Hope some of you can help.
April 11, 20242 yr Community Expert You cannot replace a 6TB disk with a 4TB SSD, for now please post the diagnostics.
April 11, 20242 yr Community Expert 57 minutes ago, Volff said: Does this mean that the data on disk 1, which for some reason is not emulated Have you tried following the procedure documented here in the online documentation accessible via the Manual link at the bottom of the Unraid GUI. In addition every forum page has a DOCS link at the top and a Documentation link at the bottom.
April 11, 20242 yr Author 40 minutes ago, JorgeB said: You cannot replace a 6TB disk with a 4TB SSD Not with the New Config tool?
April 11, 20242 yr Community Expert 4 minutes ago, Volff said: Not with the New Config tool? Only if you want to lose all previous contents of the drive. You have not mentioned if you tried the procedure for handling unmountable disks and if soi what the results were.
April 11, 20242 yr Author 1 minute ago, itimpi said: Only if you want to lose all previous contents of the drive. You have not mentioned if you tried the procedure for handling unmountable disks and if soi what the results were. The 4 TB SSD's is my only option, the 8 TB SSD's are too exspensive. I am not buying more spinning metal they die after a couple of months og use, Both Seagate and WD. I have a hardtime understanding that document. I know i will lose all the data on Disk1 with New Config, but that is my only option at this point.
April 11, 20242 yr Community Expert Check filesystem on disk1, run it without -n, and if it asks for -L use it. It the repair is successful you can then move the data to another disk(s) and do a new config with the 4TB SSD.
April 11, 20242 yr Author 7 minutes ago, JorgeB said: Check filesystem on disk1, run it without -n, and if it asks for -L use it. It the repair is successful you can then move the data to another disk(s) and do a new config with the 4TB SSD. Okay. It is running now with -L.
April 11, 20242 yr Author 10 minutes ago, JorgeB said: Check filesystem on disk1, run it without -n, and if it asks for -L use it. It the repair is successful you can then move the data to another disk(s) and do a new config with the 4TB SSD. It is done now. Shall i close Maintenance Mode and run like normal?
April 11, 20242 yr Community Expert 10 minutes ago, Volff said: Shall i close Maintenance Mode and run like normal? Yep, it should mount now, check contents an look for a lost+found folder.
April 11, 20242 yr Author 31 minutes ago, JorgeB said: Yep, it should mount now, check contents an look for a lost+found folder. Can i move data with unbalanced?
April 12, 20242 yr Author 5 hours ago, JorgeB said: Yep. Made a new config with the SSD and parity is being build.
April 13, 20242 yr Author On 4/12/2024 at 11:13 AM, JorgeB said: Yep. I mountet the new SSD, but have problem already. Disk is disabled. tower-diagnostics-20240413-1853.zip
April 14, 20242 yr Community Expert Diags are after rebooting so we can't see what happened, but most likely a power/connection issue.
April 14, 20242 yr Author 9 minutes ago, JorgeB said: Diags are after rebooting so we can't see what happened, but most likely a power/connection issue. tower-diagnostics-20240414-1144.zip
April 14, 20242 yr Community Expert 12 hours ago, JorgeB said: Diags are after rebooting so we can't see what happened
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.