July 21, 20241 yr Good afternoon, I recently picked up a referb HDD and for some reason, the system can not read it, Here are the logs of what i am able to get. I wanted some opinions on if this is fixable or just a DOA drive. I plan on shipping it off tomorrow if it can not be fixed. Let me know what you think. When i go into Attrubutes, i get this error /dev/ Unable to detect device type According to SMART i get this error. Use smartctl -h to get a usage summary below is what i get when i run the command. == START OF INFORMATION SECTION === Device Model: HUH721212ALE601 Serial Number: 8DJXEL7Y LU WWN Device Id: 5 000cca 253e91c68 Firmware Version: LEGL0002 User Capacity: 12,000,138,625,024 bytes [12.0 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database 7.3/5528 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Jul 19 19:10:00 2024 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: scsi error badly formed scsi parameters Wt Cache Reorder: Unknown (SCT Feature Control command failed) Read SMART Data failed: scsi error badly formed scsi parameters === START OF READ SMART DATA SECTION === SMART Status command failed: scsi error badly formed scsi parameters SMART overall-health self-assessment test result: UNKNOWN! SMART Status, Attributes and Thresholds cannot be read. Read SMART Log Directory failed: scsi error badly formed scsi parameters ATA_READ_LOG_EXT (addr=0x00:0x00, page=0, n=1) failed: scsi error badly formed scsi parameters Read GP Log Directory failed SMART Extended Comprehensive Error Log (GP Log 0x03) not supported Read SMART Error Log failed: scsi error badly formed scsi parameters SMART Extended Self-test Log (GP Log 0x07) not supported Read SMART Self-test Log failed: scsi error badly formed scsi parameters Selective Self-tests/Logging not supported SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 0 Celsius Power Cycle Min/Max Temperature: -3/ 3 Celsius Lifetime Min/Max Temperature: 0/ 0 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: scsi error badly formed scsi parameters Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: scsi error badly formed scsi parameters SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported ATA_READ_LOG_EXT (addr=0x11:0x00, page=0, n=1) failed: scsi error badly formed scsi parameters Read SATA Phy Event Counters failed Edited July 21, 20241 yr by razorline adding more info
July 21, 20241 yr Community Expert That looks like a bad disk, try swapping cables with another one to rule that out, if errors persist it's almost certainly the disk.
July 21, 20241 yr Author Thank you for the confirmation. Stinks the first disk i buy its DOA. Ill try a new cord but i don't think thats it, they was working with a lower TB HDD i was replacing. Edited July 21, 20241 yr by razorline
July 21, 20241 yr Community Expert You may want to try the 3.3V fix: https://www.instructables.com/How-to-Fix-the-33V-Pin-Issue-in-White-Label-Disks-/
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.